• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.2
• /
• pp.141-146
• /
• 2020

Thermoelectric Bi₂Te₃ thin films were synthesized by a co-sputtering method at 300℃. A Fe dopant was considered to enhance the thermoelectric properties of the system. The Seebeck coefficient of the Fe-doped films increased whereas the electrical conductivity decreased. As a result, the power factor of the system increased owing to the enhanced Seebeck coefficient. Grain growth inhibition was detected in the Fe-doped system, which produced more grain boundaries in the Fe-doped films than in the undoped system. The increased grain boundary scattering was deemed to be effective for a reduced thermal conductivity. This is advantageous for the preparation of high-performance thermoelectric films.

• Transactions on Electrical and Electronic Materials
• /
• v.5 no.5
• /
• pp.189-193
• /
• 2004

Pure and Sn or Pt doped $\alpha-Fe_2O_3$ thin films were prepared on $Al_2O_3$ substrates by RF-magnetron sputtering method and the sensitivities were compared. It was found that pure $\alpha-Fe_2O_3$ thin films did not exhibit much selectivity in CO and $i-C_4H_{10}$ gases while it showed the high sensitivity in proportion to the gas concentration of $C_2H_{5}OH$ gas. Pt-doped $\alpha-Fe_2O_3$ showed to be alike sensing properties as pure $\alpha-Fe_2O_3$ thin film in $C_2H_{5}OH$ gas. However, Sn-doped $\alpha-Fe_2O_3$ thin films exhibited the excellent sensitivity and selectivity in Hz gas. After microstructure modification by plasma etching on pure $\alpha-Fe_2O_3$ thin films, the gas sensing characteristics were dramatically changed.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.5
• /
• pp.1445-1453
• /
• 2013

$Zn_{(1-x)}Ni_xAl_2O_4$ (x = 0.0-1.0) spinels were prepared at $800^{\circ}C$ by co-precipitation method and characterized by infrared spectroscopy, X-ray diffraction, scanning electron microscopy and X-ray photoelectron spectroscopy. The specific surface area was determined by BET. SEM image showed nano sized spherical particles. XPS confirmed the valence states of the metals, showing moderate Lewis character for the surface of materials. The powders were successfully used as new heterogeneous catalysts of Biginelli's reaction, a one-pot three-component reaction, leading to some dihydropyrimidinones (DHPMs). These new catalysts that produced good yields of DHPMs, were easily recovered by simple filtration and subsequently reused with persistent activity, and they are non-toxic and environmentally friendly. The optimum amount of catalyst is 20% by weight of benzaldehyde derivatives, while the doping amount has been found optimal for x = 0.1.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.3
• /
• pp.843-847
• /
• 2014

In Super Junction (SJ) MOSFETs, charge balance is the most important issue of the SJ fabrication process. In order to achieve the best electrical characteristics, such as breakdown voltage and on-resistance, the N-type and P-type drift regions must be fully depleted when the drain bias approaches the breakdown voltage, which is known as the charge balance condition. In conventional charge balance analysis, based on multi-epi process SJ MOSFETs, analytical model has only N, P pillar width and doping concentration parameter. But applying a conventional charge balance principle to trench filling process, easier than Multi-epi process, is impossible due to the missing of the trench angle parameter. To achieve much more superior characteristics of on-resistance in trench filling SJ MOFET, the appropriate trench angle is necessary. So in this paper, modulated charge balance analysis is proposed, in which a trench angle parameter is added. The proposed method is validated using the TCAD simulation tool.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.294-294
• /
• 2007

Spinel cathode material $LiMn_2O_4$ is currently studied as a promising cathode material for lithium ion secondary batteries for future applications because of it is low cost, easy to be prepared and capable to be operated in high voltage range. However as a cathode material, $LiMn_2O_4$ performs a poor capacity retention which leads to short cycle life. In this study, stoichiometric $LiMn_2O_4$ was synthesized with granulation method with ion substitution to stabilize its structure and niobium doping to improve its conductivity. These well-mixed powders were calcined at $850^{\circ}C$ for 6 hours and its properties were investigated. Correlations of dopant and electrochemical properties were examined as well.

• Korean Journal of Materials Research
• /
• v.28 no.11
• /
• pp.620-626
• /
• 2018

Highly self-cleaning thin films of $TiO_2-SiO_2$ co-doped with Ag and F are prepared by the sol-gel method. The asprepared thin films consist of bottom $SiO_2$ and top $TiO_2$ layers which are modified by doping with F, Ag and F-Ag elements. XRD analysis confirms that the prepared thin film is a crystalline anatase phase. UV-vis spectra show that the light absorption of $Ag-F-TiO_2/SiO_2$ thin films is tuned in the visible region. The self-cleaning properties of the prepared films are evaluated by a water contact angle measurement under UV light irradiation. The photocatalytic performances of the thin films are studied using methylene blue dye under both UV and visible light irradiation. The $Ag-F-TiO_2/SiO_2$ thin films exhibit higher photocatalytic activity under both UV and visible light compared with other samples of pure $TiO_2$, Ag-doped $TiO_2$, and F-doped $TiO_2$ films.

• Journal of the Korean Physical Society
• /
• v.73 no.10
• /
• pp.1535-1540
• /
• 2018

In this study, we prepared and characterized Nb-doped $Li_7La_3Zr_{2-x}O_{12}$ (LLZNO) powder and pellets with a cubic garnet structure by using a modified sol-gel synthesis and hot pressing. LLZNO powder with a very small grain size and cubic structure without secondary phases could be obtained by using a synthesis method in which Li and La sources in a propanol solvent were mixed together with Zr and Nb sources in 2-methoxy ethanol. A pure cubic phase LLZNO pellet could be fabricated from the prepared LLZNO and an additional 6-wt% of $Li_2CO_3$ powder by hot pressing at $1050^{\circ}C$ and 15.8 MPa. The hot-pressed LLZNO pellet with a relative density of 99% exhibited a very dense surface morphology. The total Li ionic conductivity of the hot-pressed LLZNO was $7.4{\times}10^{-4}S/cm$ at room temperature, which is very high level compared to other reported values. The activation energy for ionic conduction was estimated to be 0.40 eV.

• Journal of the Korean Ceramic Society
• /
• v.54 no.2
• /
• pp.150-157
• /
• 2017

Three types of piezoelectric single crystals [PMN-PT (Generation I $[Pb(Mg_{1/3}Nb_{2/3})O_3-PbTiO_3]$), PMN-PZT (Generation II $[Pb(Mg_{1/3}Nb_{2/3})O_3-Pb(Zr,Ti)O_3]$), PMN-PZT-Mn (Generation III)] were grown by the solid-state single crystal growth (SSCG) method, and their dielectric and piezoelectric properties were measured and compared. Compared to (001) PMN-PT and PMN-PZT single crystals, the (001) PMN-PZT-Mn single crystals exhibited a higher transition temperature between the rhombohedral and tetragonal phases ($T_{RT}=144^{\circ}C$), as well as a higher coercive electric field ($E_C=6.3kV/cm$) and internal bias field ($E_I=1.6kV/cm$). The (011) PMN-PZT-Mn single crystals showed the highest coercive electric field ($E_C=7.0kV/cm$), and the highest stability of $E_C$ and $E_I$ during 60 cycles of polarization measurement. These results demonstrate that both Mn doping (for higher electromechanical quality factor ($Q_m$)) and a (011) crystallographic orientation (for higher coercive electric field and stability) are necessary for high power transducer applications of these piezoelectric single crystals. Specifically, the (011) PMN-PZT-Mn single crystal (Gen. III) had the highest potential for application in the fields of SONAR transducers, high intensity focused ultrasound (HIFU), ultrasonic motors, and others.

• Transactions on Electrical and Electronic Materials
• /
• v.13 no.6
• /
• pp.283-286
• /
• 2012

(1-X)$(Na_{0.5}K_{0.5})NbO_3-XK_{5.4}Cu_{1.3}Ta_{10}O_{29}$ (NKN-KCT) lead-free piezoelectric ceramics have been synthesized by the conventional solid state sintering method, and their sinterability and piezoelectric properties were investigated. Typically, this material is sintered between 1,025 and $1,100^{\circ}C$ for 2 hours to achieve the required densification. Crystalline structures and Microstructures were analyzed by X-ray diffraction and scanning electron microscope. The density, dielectric constant (${\varepsilon}_r$), piezoelectric constant $d_{33}$, electromechanical coupling factor $k_p$ and mechanical quality factor $Q_m$ value of the NKN ceramics depended upon the KCT content and the sintering temperature. In particular, the KCT addition to NKN greatly improved the mechanical quality factor $Q_m$ value. The ceramic with X = 1.0 mol% sintered at $1,050^{\circ}C$ exhibited optimum properties (${\varepsilon}_r$=246, $d_{33}$=95, $k_p$=0.38 and $Q_m$=1,826). These results indicate that the ceramic is a promising candidate material for applications in lead free piezoelectric transformer and filter materials.

• Journal of Electrochemical Science and Technology
• /
• v.14 no.3
• /
• pp.293-300
• /
• 2023

The global energy storage markets have gravitated to high-energy-density and low cost of lithium-ion batteries (LIBs) as the predominant system for energy storage such as electric vehicles (EVs). High-Ni layered oxides are considered promising next-generation cathode materials for LIBs owing to their significant advantages in terms of high energy density. However, the practical application of high-Ni cathodes remains challenging, because of their structural and surface instability. Although extensive studies have been conducted to mitigate these inherent instabilities, a two-step process involving the synthesis of the cathode and a dry/wet coating is essential. This study evaluates a one-step β-Li₂SnO₃ layer coating on the surface of LiNi_0.8Co_0.2O₂ (NC82) via the thermal segregation of Sn owing to the solubility limit with respect to the synthesis temperature. The doping, segregation, and phase transition of Sn were systematically revealed by structural analyses. Moreover, surface-engineered 5 mol% Sn-coated LiNi_0.8Co_0.2O₂ (NC82_Sn5%) exhibited superior capacity retention compared to bare NC82 owing to the stable surface coating layer. Thus, the developed one-step coating method is suitable for improving the properties of high-Ni layered oxide cathode materials for application in LIBs.