• Journal of the Korean Institute of Telematics and Electronics
• /
• v.24 no.1
• /
• pp.10-14
• /
• 1987

Considering transition gating of the input unipolar NRZ signal, the equivalent linear time-invariant model has been derived for the PLL in the timing clock recovery circuits. The magnitude of the alignment and accumulated jitter has been found along a chain of repeaters. For the timing recovery circuit of 90 Mbps optical communication system, the computer simulation shows that, for the first stage of the chain, the alignment jiter and the accumulated jitter are of -5.1766 dB and for the 7-th stage, the alignment jitter and accumulated jitter have the value of -1.0193dB, 4.9053 dB respectively.

• ETRI Journal
• /
• v.30 no.2
• /
• pp.275-281
• /
• 2008

A 40 Gb/s clock and data recovery (CDR) module for a fiber-optic receiver with improved phase-locked loop (PLL) circuits has been successfully implemented. The PLL of the CDR module employs an improved D-type flip-flop frequency acquisition circuit, which helps to stabilize the CDR performance, to obtain faster frequency acquisition, and to reduce the time of recovering the lock state in the event of losing the lock state. The measured RMS jitter of the clock signal recovered from 40 Gb/s pseudo-random binary sequence ($2^{31}-1$) data by the improved PLL clock recovery module is 210 fs. The CDR module also integrates a 40 Gb/s D-FF decision circuit, demonstrating that it can produce clean retimed data using the recovered clock.

• Journal of Korea Multimedia Society
• /
• v.8 no.10
• /
• pp.1403-1410
• /
• 2005

The synchronization problem is directly related to the quality of service in multimedia communication and especially in real-time communication. In this study, we found the cause of clock fluctuation between encoder and decoder in MPEG-2 system layer was that the standard decoder design only considered a fixed time delay component. To solve it, we proposed Extended-SRTS algorithm, which uses STC as service clock by synchronizing transport stream. As the result, we can improve the effect of frequency-drift, time-varying-network-jitter and packing-jitter and so on And by virtue of this algorithm, we can make low the dependency of network clock, which makes easy to synchronize and connect transparently at the ends point, we expect the proposed algorithm can be widely applied to the field of real -time multimedia communications.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.3
• /
• pp.287-292
• /
• 2016

A multiphase clock and data recovery (CDR) circuit having a novel rotational bang-bang phase detector (RBBPD) is demonstrated. The proposed 1/4-rate RBBPD decides the locking point using a single clock phase among sequentially rotating 4 clock phases. With this, our RBBPD has significantly reduced power consumption and chip area. A prototype 10-Gb/s 1/4-rate CDR with RBBPD is successfully realized in 65-nm CMOS technology. The CDR consumes 5.5 mW from 1-V supply and the clock signal recovered from $2^{31}-1$ PRBS input data has 0.011-UI rms jitter.

• Journal of Broadcast Engineering
• /
• v.16 no.5
• /
• pp.722-737
• /
• 2011

In this paper, we propose an estimation of network jitter that occurs when transmitting TCP packets containing MPEG-2 TS in progressive streaming service over wired or wireless Internet networks. Based on the estimated network jitter size, we can calculate required de-jitter buffering time to absorb the network jitter at the receiver side. For this purpose, by exploiting the PCR timestamp existing in the TS packet header, we create a new timestamp information that is marked in the optional field of TCP packet header to estimate the network jitter. By using the proposed de-jitter buffering scheme, it is possible to employ the conventional T-STD buffer model without any modification in the progressive streaming service over IP networks. The proposed method can be applicable to the recently developed international standard, MPEG DASH (dynamic adaptive streaming over HTTP) technology.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.136-139
• /
• 2003

A clock recovery circuit for a 40 Gb/s optical receiver has been designed and implemented. The clock recovery circuit consists of signal amplifiers, a nonlinear circuit with diodes, and a bandpass filter Before implementing the 40 Gb/s clock recovery circuit, a 10 Gb/s clock recovery circuit has been successfully implemented and tested. With the 40 Gb/s clock recovery circuit, when a 40 Gb/s NRZ signal of -10 dBm was applied to the input of the circuit, the 40 GHz clock was recovered with the -20 dBm output power after passing through the nonlinear circuit. The output signal from the nonlinear circuit passes through a narrow-band filter, and then amplified. The implemented clock recovery circuit is planned to be used for the input of a phase locked loop to further stabilize the recovered clock signal and to reduce the clock jitter.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.11
• /
• pp.1144-1149
• /
• 2009

This paper deals with the time synchronization problem over SpaceWire links. SpaceWire is a standard for high-speed links and networks between spacecraft components, which was invented for better, cheaper, faster on-board data handling in spacecraft. The standard defines Time-Code for time distribution over SpaceWire network. When a Time-Code is transmitted, transmission delay and jitter is unavoidable. In this paper, a mechanism to remove Time-Code transmission delay and jitter over SpaceWire links is proposed and implemented with FPGA for validation. The proposed mechanism achieves high resolution clock synchronization over SpaceWire links, complies with the standard and can be easily adopted over SpaceWire network.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.17 no.1
• /
• pp.48-55
• /
• 2017

This paper proposes a new link structure that transmits power, clock, and data through a single optical fiber for a future automotive network. A pulse-position modulation (PPM) technique is adopted to guarantee a DC-balanced signal for robust power transmission regardless of transmitted data pattern. Further, circuit implementations and theoretical analyses for the proposed PPM transceiver are described in this paper. A prototype transceiver fabricated in 65-nm CMOS technology, is used to verify the PPM signaling part of the proposed system. The prototype achieves a $10^{-13}$ bit-error rate and 0.188-UI high frequency jitter tolerance while consuming 14 mW at 800 Mb/s.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.3
• /
• pp.319-329
• /
• 2016

High-level design aids are mandatory for design of a continuous-time delta-sigma modulator (CTDSM). This paper proposes a top-down methodology design to generate a noise transfer function (NTF) which is compensated for excess loop delay (ELD). This method is applicable to low pass loop-filter topologies. Non-ideal effects including ELD, integrator scaling issue, finite op-amp performance, clock jitter and DAC inaccuracies are explicitly represented in a behavioral simulation of a CTDSM. Mathematical modeling using MATLAB is supplemented with circuit-level simulation using Verilog-A blocks. Behavioral simulation and circuit-level simulation using Verilog-A blocks are used to validate our approach.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.6
• /
• pp.594-600
• /
• 2015

A 1.25 GHz multi-phase phase-rotating PLL is proposed for oversampling CDR applications and implemented with a low power and small area. Eight equidistant clock phases are simultaneously adjusted by the phase interpolator inside the PLL. The phase interpolator uses only two complementary clocks from a VCO, but it can cover the whole range of phase from $0^{\circ}$ to $360^{\circ}$ with the help of a PFD timing controller. The output clock phases are digitally adjusted with the resolution of 25 ps and both INL and DNL are less than 0.44 LSB. The proposed PLL was implemented using a 110 nm CMOS technology. It consumes 3.36 mW from 1.2 V supply and occupies $0.047mm^2$. The $jitter_{rms}$ and $jitter_{pk-pk}$ of the output clock are 1.91 ps and 18 ps, respectively.