• Bulletin of the Korean Chemical Society
• /
• v.30 no.8
• /
• pp.1749-1754
• /
• 2009

Solubilities of carbon dioxide (C$O_2$) in a series of fluorine-free room temperature ionic liquids (RTILs), dialkylimidazolium dialkylphosphates and dialkylimidazolium alkylphosphites, were measured at 313∼333 K and pressures up to 5 MPa. Henry’s law coefficients as the solubility parameter of C$O_2$ in RTILs were derived from the isotherm of fugacity versus C$O_2$ mole fraction. The C$O_2$ solubility in a phosphorus-containing RTIL was found to increase with the increasing molar volume of the RTIL. In general, dialkylimidazolium dialkylphosphate exhibited higher absorption capacity than dialkylimidazolium alkylphosphite as long as the RTILs possess an identical cation. Among RTILs tested, 1-butyl-3-methylimidazolium dibutylphosphate [BMIM][B$u_2PO_4$] and 1-butyl-3-methylimidazolium butylphosphite [BMIM][BuHP$O_3$] exhibited similar Henry’s law coefficients to 1-butyl-3-methylimidazolium bis (trifluoromethylsulfonyl)imide ([BMIM][T$f_2$N]) and 1-butyl-3-methylimidazolium tetrafluoroborate ([BMIM][B$F_4$]), respectively. The Krichevsky-Kasarnovsky equation was employed to derive the C$O_2$ solubility parameter (Henry’s law coefficient) from the solubility data measured at elevated pressures.

• Journal of the Korea Society for Simulation
• /
• v.27 no.3
• /
• pp.23-36
• /
• 2018

Discrete Event System Specification (DEVS) has been used for decades as it provides sound semantics for hierarchical modular specification of discrete event systems. Instead of the mathematical specification, the DEVS diagram, based on the structured DEVS formalism, has provided more intuitive and convenient representation of complex DEVS models. This paper proposes a clean room process for implementation and verification of a DEVS diagram model specification into a simulation software source code. Specifically, it underlies a sequence of transformation steps from conformance and integrity checking of a given diagram model, translation into a corresponding tabular model, and finally conversion to a simulation source code, with each step being inversely verifiable for traceability. A simple example helps developers to understand the proposed process with associated transformation methods; a case study shows that the proposed process is effective for and adaptable to practical simulation software development.

• Journal of Pharmaceutical Investigation
• /
• v.33 no.2
• /
• pp.145-149
• /
• 2003

Manufacturing facilities of the pharmaceuticals must meet certain level of the cleanness required so that foreign substances such as dust, moisture, heat, microorganism, or virus do not contaminate the product. In case of radiopharmaceuticals for medical treatment and diagnosis, not only should the operators and environment be protected from radiation but also need to be isolated from the foreign contaminant. Therefore, manufacturing facilities for radiopharmaceuticals must satisfy the design standards of both hot cell and clean room which are specified by GMP. However, standards of maintaining negative pressure for preventing spread of radioactive contaminant in isolated facilities conflict with the standards of maintaining positive pressure for keeping cleanness. To solve this problem, air pressure of hot cell was designed lower than in the adjacent area to meet standards of the radiation safety. To keep higher cleanness in certain part of the hot cell for filling, minimal relative positive pressure allows. In order to effectively maintain the cleanness that is required for production of Tc-99m generator, which takes 70% of whole demand of radiopharmaceuticals, the rooms placed in each side of production room are used as a buffer area and three lead hot cells are installed in production room. In this research, we established the appropriate engineered design concept for Tc-99m generator manufacturing facility, which satisfies both GMP cleanness standard for preventing particles, bacteria, other contaminants and the regulations of radiation safety for supervising and controlling the amount of radiation exposure and exhausted radioactivity. And the concept of multi-barrier buffer zones is introduced to apply negative air pressure for hot cell with first priority and to continue relative positive air pressure for clean room.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.301.1-301.1
• /
• 2016

We report an ultraclean, cost-effective, and easily scalable method of transferring and patterning large-area graphene using pressure sensitive adhesive films (PSAFs) at room temperature. This simple transfer is enabled by the difference in wettability and adhesion energy of graphene with respect to PSAF and a target substrate. The PSAF transferred graphene is found to be free from residues, and shows excellent charge carrier mobility as high as ${\sim}17,700cm^2/V{\cdot}s$ with less doping compared to the graphene transferred by thermal release tape (TRT) or poly(methyl methacrylate) (PMMA) as well as good uniformity over large areas. In addition, the sheet resistance of graphene transferred by recycled PSAF does not change considerably up to 4 times, which would be advantageous for more cost-effective and environmentally friendly production of large-area graphene films for practical applications.

• Macromolecular Research
• /
• v.14 no.5
• /
• pp.545-551
• /
• 2006

Aqueous dispersions of pristine and functionalized (COOH- and $NH_2$-) multi-walled, carbon nanotubes (MWNTs) were prepared by using three types of surf act ants: sodium dodecyl sulfate (SDS, anionic), PEO-PPO-PEO (Pluronic P84, non-ionic), and poly(styrene/$\alpha-methyl$ styrene/acrylic acid) random terpolymer, i.e., alkali-soluble resin (ASR). The aggregate size, $\zeta-potential$, and storage stability of the MWNT aqueous dispersions were investigated by using dynamic light scattering and the turbidity method at room temperature. The exfoliation of the MWNT aggregates was determined by a UV-visible spectrophotometer and the morphology of the surfactant-coated MWNTs was observed by transmission electron microscopy (TEM). In all cases, ASR showed better dispersion stability with the smallest aggregate size, compared with the other surfactants, because of its unique molecular structure, i.e., randomly incorporated carboxylic acid groups and planar phenyl groups that can be irreversibly and effectively adsorbed on the MWNT surface. A predominantly-exfoliated morphology of MWNTs was observed in the presence of ASR from the strong intensity of the UV-vis spectrum at 263 nm.

• Journal of the Korean Society of Safety
• /
• v.24 no.6
• /
• pp.50-54
• /
• 2009

Ionizer is used for improving manufacturing process and reducing inferior goods in the clean room. As a general rule, neutralization of the electrostatic charge is most important to make TFT-LCD, PDP and OLED. Pulse AC-static eliminator with output voltage of about 10.5kV has been used these days as neutralization device. But this device has a problem with lower performance which was caused by particles-adhesion on the electrode when it has been used for a long time. So we studied to solve the problem with lower performance using high Frequency(72kHz) static eliminator which was produced by Piezo transformer device, and compared Pulse-AC type with Piezo-electronic device such as decay time and ion balance for 10 weeks periods. As a result of this study, we found that Piezo transformer device has been maintained normal condition for 10 weeks. Also, we made the rule by this study, normally Piezo transformer device has to clean the electrode during every 11th weeks.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.21 no.1
• /
• pp.63-70
• /
• 2009

The air sterilization systems are investigated experimentally in this paper. The goal is to reduce bacteria, mold and viruses in office air by using a UV sterilizer installed inside a partition panel and wall-mounted unit. These systems allow occupants to turn the system on/off and to control the incoming air speed and direction. The partition air sterilization system conditions and sterilizes the air, and then delivers the clean air into the personal task area through the partition panels, which are connected to the pressurized under-floor plenum. Room air exits through the return grills mounted on the ceiling. The wall-mounted air sterilization system sterilizes the air, and then delivers the clean air to the personal task area from the wall. In this study a full-size experimental environment is established to investigate the immunization performance of these air sterilization systems. A typical office space scale is used in this study in order to find an optimal system to achieve a sterilized healthy micro-environment. Multiple system parameters, including volume flow rate and velocity of supplied air, were regulated during the experiments. The more air contact these air sterilization systems had, the better disinfection performance. Over 90% of eradication ratios were obtained by these two air sterilization systems. The results indicate that these systems can efficiently disinfect office air contamination.

• Korean Institute of Interior Design Journal
• /
• v.24 no.1
• /
• pp.189-196
• /
• 2015

As the number of children's libraries has increased in Korea, it has been discussed to improve the quality of design in the libraries. In a reading room of children's library, spatial consideration should be focused on the children under 10 years old since they are in important points to learn Hangul and to develop reading habits. This study is aimed to examine the characteristics of a floor-sitting reading room, where children can feel like a home, stay in clean and safe and play while reading. The seven case studies of floor-sitting reading rooms are analyzed from the viewpoint of each factor of physical environment, including structure, furniture, and decoration. The following is the summary of findings of this study. First, floor-sitting reading rooms tend to compose main reading areas around bookshelves. Reading areas create the characters by changing floor levels and arranging furniture associated with windows, columns, and wall-type bookshelves. In the reading areas, movable low-level tables are frequently placed for flexible space uses, and seats for reading tend to put together with fixed bookshelves. Second, the central areas of the reading rooms are often shaped in the forms of pods, storytelling areas, sculptures, and unique furniture. Especially storytelling areas and pods play the cores of the reading rooms with the varying steps of floors and pictorial graphics on walls. Third, decoration elements in the reading rooms are designed with graphics, visual displays, and sculptural decorations. In my case studies, spatial elements such as reading nooks, attics, tunnels, and shelters are not often found in the floor-sitting reading rooms even though children like to have them. Since it is the advantage of floor-sitting reading rooms where children can take off shoes and act freely, we should look for the design of such spatial elements in the floor-sitting reading rooms.

• Journal of The Korea Institute of Healthcare Architecture
• /
• v.28 no.2
• /
• pp.31-38
• /
• 2022

Purpose: This study presents the results of the analysis on space utilization of kidney dialysis units in regional public hospitals, which plays a key role in local public medical services. The result aims to achieve safety from infection, allow comfort for the dialysis environment, and stability for medical support. The purpose of this study is to present fundamental data for architectural plans for the kidney dialysis unit, as well as to alleviate potential infectious diseases such as COVID-19. Methods: For research purposes, the investigation and analysis of space utilization were based on architectural floor plans, research papers and literature, related legal systems, and public statistics. Of the main 35 regional public hospitals, in regards to data accessibility, 15 facilities were selected to conduct the survey and analysis for the objective. Results: The space composition by area research results of kidney dialysis units in public hospitals are as follows: Firstly, most targets do not have required rooms in the access and support area, except for the hemodialysis beds in the treatment section. Secondly, the access area requires necessary room and space design that took into consideration of convenience and accessibility for patients. Thirdly, in regards to infection prevention and control, proper circulation and room plan is essential for storage and disposal of contaminated products and linen after use. For the treatment area, the arrangement plan needs to establish a visual connection between the isolation room, the nursing station, and the bed area. Additionally, consideration of circulation in the preparation, treatment, observation, examination, and all other rooms in the facility is required. Lastly, for the support area, the room is designed to consider adequate working and meeting spaces for the medical staff, consultation space for patients or guardians, separate storage and disposal of clean and contaminated items, and the storage of various equipment for dialysis. Implications: In preparation for the increase in chronic kidney failure patients and the spread of infectious diseases, such as COVID-19, the researched data demonstrates the basic guidelines for space composition of kidney dialysis units and the significant role of regional public hospitals.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.1
• /
• pp.603-608
• /
• 2018

Although the voltage-applied discharge method is most widely used in the semiconductor and display industries, periodic management costs are incurred because the method causes defects due to the absorption of ambient fine dust and causes emitter tip contamination due to the discharge. The emitter tip contamination problem is caused by the accumulation of fine particles in ambient air due to the corona discharge of the ionizer. Fuzzy ball generation accelerates the wear of the emitter tip and deteriorates the performance of the ionizer. Although a mechanical cleaning method using a manual brush or an automatic brush is effective for contaminant removal, it requires management of additional mechanical parts by the user. In some cases, contaminants accumulated in the emitter may be transferred to the wafer or product. In order to solve this problem, we developed an ionizer for a clean environment that can remove the pencil-type emitter tip and directly ionize the surrounding gas molecules using the tungsten wire located inside the ion tank. As a result of testing and certification by the Korea Institute of Machinery and Materials, the average concentration was $0.7572particles/ft^3$, the decay time was less than two seconds, and the ion valance was 7.6 V, which is satisfactory.