• Communications for Statistical Applications and Methods
• /
• v.3 no.3
• /
• pp.161-168
• /
• 1996

This paper describes a sampling method, which can be used instead of the simple random sampling without replacement(SRSWOR). This method, circular sampling, assumes that the sampling units of the population are arranged in circular format, and randomly selects as many as samples of contiguous units. Therefore this method gathers information quicker and easier than STSWOR. In certain circumstances, the reliability of this method is better than that of STSWOR. And of circular sampling would be applied to nonprobability could be determined. methods, the reliability of the sample results in terms of probability could be determined.

• Journal of Korean Society of Forest Science
• /
• v.4 no.1
• /
• pp.26-29
• /
• 1965

1. The purpose of this study was to find out the best sampling form and sampling unit in forest survey. 2. The value of small sampling unit was over estimated in comparison with that of large sampling unit. 3. The value of circular form was over estimated in comparison with that of the others. 4. The smallest unit for estimation in area sampling were as follows. a) 0.06 ha. in the rectangular plot. b) 0.08 ha. in the square plot. c) 0.10 ha. in the circular plot. 5. Conclusion was as follows. The best sampling unit was 0.06 hectoare in the rectangular plot, which was most economic above all and gave preferable result for in the forest survey.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.16 no.6
• /
• pp.22-30
• /
• 1979

A new circular ring position camera tomographic system termed "Oscillatory Dichotomic Ring" system is proposed and its performance is simulated. It is basically a circular ring system, composed of two half rings, which has the capability of scanning so that any sampling intervals can be obtained. Since finer sampling means poorer photon statistcs, simulations with varous signal dependent statistical noise effects, ray sampling and arrangement as well as related artifacts peculiar to the proposed Dichotomic Ring system are made.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03a
• /
• pp.229-232
• /
• 2008

This study presents a numerical procedure to optimize the shape of stepped circular pin-fins to enhance turbulent heat transfer. The KRG method is used as an optimization technique with Reynolds-averaged Navier-Stokes analysis of fluid flow and heat transfer with shear stress transport turbulent model. The objective function is defined as a linear combination of heat transfer and friction loss related terms with a weighting factor. Ten training points are obtained by Latin Hypercube Sampling for two design variables. Optimum shape has been successfully obtained with the increased objective function.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.10a
• /
• pp.229-232
• /
• 2008

This study presents a numerical procedure to optimize the shape of stepped circular pin-fins to enhance turbulent heat transfer. The KRG method is used as an optimization technique with Reynolds-averaged Navier-Stokes analysis of fluid flow and heat transfer with shear stress transport turbulent model. The objective function is defined as a linear combination of heat transfer and friction loss related terms with a weighting factor. Ten training points are obtained by Latin Hypercube Sampling for two design variables. Optimum shape has been successfully obtained with the increased objective function.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.2
• /
• pp.347-356
• /
• 1996

In this paper, we present the circular array structure for estimating the temporal and spatial specturm of multiple narrowband incoherent signals which have different frequencies. The conventional linear array is computationally demanding for simultaneously estimating the spatial and temporal spectrum since it requires the tapped delay line filer. The statistical performance of the circular array is never deteriorated eve though it requires much less computational load than the uniform linear array. Especially, it is shown that the circular array resolves the direction-of-arrivals of the multiple signals without the spatial and temporal aliasing the fundamental nonuniform-sampling property prossessed by it. Computer simulation results are shown to demonstrate the better performance achieved with the circular array geometry relative to that obtained with a uniform linear array with taps.

• Journal of Advanced Marine Engineering and Technology
• /
• v.18 no.1
• /
• pp.60-72
• /
• 1994

The effect of free stream tubulence on the coherent structure in the near wake of a circular cylinder was investigated by a conditional sampling technique. The measurements were made from C.T.A. with hot wire I-probe and a Split-film sensor. Contours of phase-averaged velocity and vorticities were presented and discussed. It was found that the value of the vortex strength increased with increasing free stream turbulence which can enhance the roll-up of the shear layer.

• Tunnel and Underground Space
• /
• v.13 no.5
• /
• pp.344-352
• /
• 2003

The procedures to correct sampling biases for discontinuity data obtained from 1D survey line(borehole or scanline) is addressed. The Probability of intersection between the survey line and a circular discontinuity is considered, and a correction far orientation bias is developed assuming discontinuities as equivalent circular disks. The correction incorporates the effect of the angle between the direction of survey line and each discontinuity plane belonging to the discontinuity cluster, size of each discontinuity and length of the survey line. A procedure is provided to estimate unbiased discontinuity spacing parameters using the discontinuity spacing data based on the measurements carried out on a finite length of the survey line.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.11 no.2
• /
• pp.24-29
• /
• 2002

A study for the circularity of machine tool is classified into two ways. One is to measure the circularity of machine tool by a existing measuring device. The other is to measure the circularity by remodeling the existing measuring device. We will improve on measurement of circularity using circular test method by a two-dimensional probe and a master ring for machining tools and investigate influence of trigger method, acceleration data sampling.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.12
• /
• pp.909-909
• /
• 2022