• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.10
• /
• pp.27-33
• /
• 2016

This paper proposes a Low Noise Amplifier (LNA) with chopper stabilization technique with a sample-hold circuit. Chopper stabilization technique is effective in terms of reducing low frequency offset and flicker noise. Conventional chopper amplifier has a disadvantage in area because of using Low Pass Filter (LPF) for remove chopping spike. The proposed chopper amplifier employed sample and hold technique to decrease chopping spike instead of LPF that improves 36% in voltage damping and 11% in area.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.10 no.4
• /
• pp.276-281
• /
• 2010

A 2.5 V feed-forward second-order deltasigma modulator for audio application is presented. A 9-level quantizer with a tree-structured dynamic element matching (DEM) was employed to improve the linearity by shaping the distortion resulted from the capacitor mismatch of the feedback digital-toanalog converter (DAC). A chopper stabilization technique (CHS) is used to reduce the flicker noise in the first integrator. The prototype delta-sigma analogto-digital converter (ADC) implemented in a 65 nm 1P8M CMOS process occupies 0.747 $mm^2$ and achieves 109.1 dB dynamic range (DR), 85.4 dB signal-to-noise ratio (SNR) in a 24 kHz audio signal bandwidth, while consuming 14.75 mW from a 2.5 V supply.

• ETRI Journal
• /
• v.33 no.6
• /
• pp.897-903
• /
• 2011

A hybrid ${\Delta}{\Sigma}$ modulator for audio applications is presented in this paper. The pulse generator for digital-to-analog converter alleviates the requirement of the external clock jitter and calibrates the coefficient variation due to a process shift and temperature changes. The input resistor network in the first integrator offers a gain control function in a dB-linear fashion. Also, careful chopper stabilization implementation using return-to-zero scheme in the first continuous-time integrator minimizes both the influence of flicker noise and inflow noise due to chopping. The chip is implemented in a 0.13 ${\mu}m$ CMOS technology (I/O devices) and occupies an active area of 0.37 $mm^2$. The ${\Delta}{\Sigma}$ modulator achieves a dynamic range (A-weighted) of 97.8 dB and a peak signal-to-noise-plus-distortion ratio of 90.0 dB over an audio bandwidth of 20 kHz with a 4.4 mW power consumption from 3.3 V. Also, the gain of the modulator is controlled from -9.5 dB to 8.5 dB, and the performance of the modulator is maintained up to 5 nsRMS external clock jitter.

• Journal of Semiconductor Engineering
• /
• v.2 no.1
• /
• pp.109-118
• /
• 2021

This review paper describes the overall operating principle of a discrete-time delta-sigma modulator (DTDSM) and a continuous-time delta-sigma modulator (CTDSM) using a switched-capacitor (SC). In addition, research that has solved the problems related to each delta-sigma modulator (DSM) is introduced, and the latest developments are explained. This paper describes the chopper-stabilization technique that mitigates flicker noise, which is crucial for the DSM. In the case of DTDSM, this paper addresses the problems that arise when using SC circuits and explains the importance of the operational transconductance amplifier performance of the first integrator of the DSM. In the case of CTDSM, research that has reduced power consumption, and addresses the problems of clock jitter and excess loop delay is described. The recent developments of the analog front end, which have become important due to the increasing use of wireless sensors, is also described. In addition, this paper presents the advantages and disadvantages of the three-opamp instrumentation amplifier (IA), current feedback IA (CFIA), resistive feedback IA, and capacitively coupled IA (CCIA) methods for implementing instrumentation amplifiers in AFEs.

• Journal of IKEEE
• /
• v.18 no.1
• /
• pp.119-127
• /
• 2014

This paper presents a CMOS readout circuit for MEMS(Micro Electro Mechanical System) acceleration sensors. It consists of a MEMS accelerometer, a capacitance to voltage converter(CVC) and a second-order switched-capacitor ${\Sigma}{\Delta}$ modulator. Correlated-double-sampling(CDS) and chopper-stabilization(CHS) techniques are used in the CVC and ${\Sigma}{\Delta}$ modulator to reduce the low-frequency noise and DC offset. The sensitivity of the designed CVC is 150mV/g and its non-linearity is 0.15%. The duty cycle of the designed ${\Sigma}{\Delta}$ modulator output increases about 10% when the input voltage amplitude increases by 100mV, and the modulator's non-linearity is 0.45%. The total sensitivity is 150mV/g and the power consumption is 5.6mW. The proposed circuit is designed in a 0.35um CMOS process with a supply voltage of 3.3V and a operating frequency of 2MHz. The size of the designed chip including PADs is $0.96mm{\times}0.85mm$.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.10a
• /
• pp.221-224
• /
• 2012

This paper presents a CMOS interface circuit for MEMS acceleration sensor. It consists of a capacitance to voltage converter(CVC), a second-order switched-capacitor (SC) integrator and comparator. A bandgap reference(BGR) has been designed to supply a stable bias to the circuit and a ${\Sigma}{\Delta}$ Modulator with chopper - stabilization(CHS) has also been designed for more suppression of the low frequency noise and offset. As a result, the output of this ${\Sigma}{\Delta}$ Modulator increases about 10% duty cycle when the input voltage amplitude increases 100mV and the sensitivity is x, y-axis 0.45v/g, z-axis 0.28V/g. This work is designed and implemented in a 0.35um CMOS technology with a supply voltage of 3.3V and a sampling frequency of 3MHz sampling frequency. The size of the designed chip including PADs is $0.96mm{\times}0.85mm$.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.569-572
• /
• 2014

This paper presents a CMOS switched-capacitor interface circuit for MEMS capacitive sensors. It consist of a capacitance to voltage converter(CVC), a second-order ${\Sigma}{\Delta}$ modulator, and a comparator. A bias circuit is also designed to supply constant bias voltages and currents. This circuit employes the correlated-double-sampling(CDS) and chopper-stabilization(CHS) techniques to reduce low-frequency noise and offset. The designed CVC has a sensitivity of 20.53mV/fF and linearity errors less than 0.036%. The duty cycle of the designed ${\Sigma}{\Delta}$ modulator output increases about 5% as the input voltage amplitude increases by 100mV. The designed interface circuit shows linearity errors less than 0.13%, and the current consumption is 0.73mA. The proposed circuit is designed in a 0.35um CMOS process with a supply voltage of 3.3V. The size of the designed chip including PADs is $1117um{\times}983um$.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.8 no.6
• /
• pp.8-16
• /
• 1971

This paper describes the transistorized linear counting ratemeter which can be uses to indicate on the meter or record the counting rates of the nuclear radiations produced from the atomic reactor or from the radio isotopes. Tte feature of this ratemeter is the use of the transistor chopper for good stabilization. At the input stage of the a. c. amplifier a composite emitter follower buffer stage has been used to give the high input impedance. A hybrid parameter equivalent circuit was modeled for the analysis of this buffer stage. The counting rates can be linearly measured from few CPS up to 100KCPS in 4 ranges. The resolution is less than 0.5$\mu$sec and the output drift at the room temperature with 7-hour continuous operation is in the order of $\pm$0.5$\mu$A.

• Journal of the Korean Society of Safety
• /
• v.9 no.4
• /
• pp.49-57
• /
• 1994

In this paper, a speed controller using a controller is implemented and applied to a DC motor for FA ( Factory Automation ). The objective of this paper treats the analytical and experimental studies on the improvement of control circuit and control method using a SCR-LEONARD circuit for the speed control of DC motor. This system is concerned with stabilization of single input or single output systems, so the plant (SCR-LEONARD+DC motor) is simplified to the first order system. The parameters for the PID controller are obtained by the transient-response tunning method, and this control scheme has a backward-shift operator. The control algorithms (Chopper＋transient response tunning) is used to check the performance of PID Controller through Computer simulations and experiments. The good experiment results show that the direct control of the DC motor applied to industrial field such oi factory automation.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.4
• /
• pp.481-487
• /
• 2016

A new two-line based inversion driving method is introduced for low power display-driver ICs. By inserting a timing offset between the chopper stabilization and the alternation of LCD polarity, we can reduce power consumption without noticeable degradation in the display quality. By applying the proposed scheme to 12" LCD applications, we achieved 7.5% and 27% power saving in the display-driver IC with white and black patterns, respectively.