• Journal of the Korean Vacuum Society
• /
• v.21 no.6
• /
• pp.348-353
• /
• 2012

We investigated chemical states of a $Sb_2Te_3$ thin film with the polycrystalline phase by using high-resolution x-ray photoelectron spectroscopy with synchrotron radiation. The $Sb_2Te_3$ thin film was formed by sputtering. The rhombohedral phase was confirmed by x-ray diffraction. To remove the surface oxide, we performed $Ne^+$ ion sputtering for 1 hour with the beam energy of 1 kV and post-annealing at $100^{\circ}C$ for 5 min in ultra-high vacuum. We obtained the Te and Sb 4d core-levels spectra with the peaks at the binding energies of 40.4 and 33.0 eV, respectively. The full-width of half maximum of both the Te and Sb $4d_{5/2}$ core-levels is 0.9 eV. The Te and Sb core-levels only show a single chemical state, and we also confirmed the stoichiometry of approximately 2 : 3.

• Korean Chemical Engineering Research
• /
• v.43 no.2
• /
• pp.249-258
• /
• 2005

A two-column six-step pressure swing adsorption(PSA) process was to study separation of hydrogen from hydrogen and methane($60_{vol}%/40_{vol}%$) binary system onto activated carbon adsorbent. The effects of the feed gas pressure, the feed flowrate and the P/F(purge to feed) ratio on the process performance were evaluated. The cyclic steady-states of PSA process were reached to after 15 cycles. $H_2$ purity increases according as the P/F ratio and pressure increase and the feed flow rate decreases; however, $H_2$ recovery shows an opposite phenomena to the purity. PSA process simulation studied to find optimum operation condition. In the results, 22 LPM feed flowrate, 11 atm adsorption pressure and 0.10 P/F ratio might be optimal values to obtain more than 75% recovery and 99% purity hydrogen. In this study was non-isothermal and non-adiabatic model considering linear driving force(LDF) model and Langmuir-Freundlich adsorption isotherm considered to compare between prediction and experimental data.

• Journal of Adhesion and Interface
• /
• v.22 no.4
• /
• pp.136-143
• /
• 2021

Polyurea has been investigated as a polymer matrix for composite materials because of its high mechanical strength. Although polyurea has a similar chemical structure to polyurethane, it has much higher strength and durability. In this study, the fabrication of polyurea composites reinforced with carbon nanotube (CNT) and graphene oxide (GO) is demonstrated to enhance the tensile strength of the glass fibers composite. Using FTIR and Raman spectroscopies, the chemical structures of polyurea, CNT, and GO are investigated. As a result, spectroscopy analysis reveals that the chemical structure of CNT, GO, and polyurea is maintained during the fabrication of the composite structure. Scanning electron microscopy reveals the uniform distribution of CNT and GO across the polyurea matrix. The reinforcement of 1 wt% CNT in polyurea enhances the tensile strength of CNT/polyurea composites. In contrast, the reinforcement of GO in polyurea induces the degradation of the tensile strength of GO/polyurea composites.

• Journal of Environmental Health Sciences
• /
• v.48 no.4
• /
• pp.195-205
• /
• 2022

Background: The biggest concern when using household chemical products is the health risk from inhalation exposure. Objectives: The purpose of this paper was to provide information necessary for estimating inhalation exposure factors in several countries/organizations and to present some examples. Methods: We attempted to use PRISMA-ScR for a systematic review, but no major reports were found. We used the Google search function instead to find 'exposure factor handbook'. As for the results, inhalation exposure factors from South Korea, the United States, Canada, the EU, Australia, Japan, and China were compared. Results: The basic concept and origin of exposure factors was the US Environmental Protection Agency's Exposure Factor Handbook. Its latest version is 2011, but several chapters have been updated in 2017, 2018, and 2019. South Korea's Exposure Factor Handbook was updated in 2019, more recently than those of other countries, and was systematically investigated. In South Korea, the average daily respiratory rate is 14.62 m³/day for adults and 12.73 m³/day for children. It is difficult to compare breathing rate by country because each country divides age groups differently and uses different methods to estimate it. Information on household chemical products, space used, and ventilation rate are in the exposure factor handbook in some countries and not in others. It is not in the handbook in South Korea, but in the notice from the NIER (National Institute of Environmental Research), a sub-regulation of the Chemical Product Safety Act. Conclusions: The exposure factors registered in South Korea's exposure factor handbook have been systematically studied and reflect the most recent data. When using data not in the relevant handbook, data from other countries might be applied, but it should be determined whether the nature and quality of the original data have been managed.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.31 no.4
• /
• pp.454-464
• /
• 1986

To find main factors to affect tobacco culture and quality, NC 2326 (Nicotiana tabacum L.) was cultivated in Korea and in the United States under different plant density, fertilization, mulching and curing. Among the chemical characteristics of the both experimental soils, the organic matters were similar concentration in both locations but effective phosphorous contents were higher in Oxford in the United States. Plant height, length and width of the largest leaf, leaf thickness, and midrib ratios were larger in Oxford than in Suwon in Korea. Also they were larger in non mulching system than in mulching system. But the total numbers of the leaves were decreased in non mulching system. The content of nicotine was higher in the plant grown in Suwon than in Oxford. The concentrations of nicotine and sugar tend to increase in mulching system comparing of non mulching system. During the growing, the concentration of non-volatile organic acids was higher in Suwon, while it was lower in cured leaf produced in Suwon. Also the contents of total fatty acids were lower in the harvested leaf grown in Suwon, but not in cured tobacco. Forty three compounds identified among the volatile oils from these experimental samples were quantified. The concentrations of the major components related to the tobacco flavour such as damascone, damascenone, solanone, nor-solanadione, and megastigmatrienones were higher in the cured tobacco produced in Oxford rather than in Suwon.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.22 no.4
• /
• pp.54-61
• /
• 2014

This study was conducted to investigate the effect of Actinomyces sp. and Bacillus sp., United States granular microorganisms and Japan granular microorganisms on turfgrass growth and thatch decomposing of creeping bentgrass in golf course by measuring turf color index, chlorophyll index, thatch content of soil, root length, turf density and chemical properties and thatch content of soil. Fertilizer treatment was designed as follows; control(CF; compound fertilizer), microorganism medium(M; CF+M), microorganism medium and livestock manure fertilizer(M-L; CF+M+LMF), microorganism medium, livestock manure fertilizer and amino acid liquid fertilizer(M-L-A; MM+LMF+ALF), United States granular microorganisms(USGM; CF+USGM), Japan granular microorganisms(CF+JGM). Soil properties investigated after experiment was scarcely affected by applied fertilizers in root zone of creeping bentgrass. The turf color index and chlorophyll index of M, M-L, M-L-A, USGM, JGM treatment were higher than those of CF. The turfgrass root in M-L treatment was longer than others. The thatch content of soil in M treatment was longer than others. The thatch content of M was decreased than that of CF by 6.8%. These was suggested that application of M induced the development of quality and growth of creeping bentgrass by assisting turfgrass growth and thatch decomposing.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.12
• /
• pp.56-63
• /
• 1994

The effects of sulfur treatments on the barrier heithts of Schottky contacts and the interface-state density of metal-insulator-semiconductor (MIS) capacitors on InP have been investigated. Schottky contacts were formed by the evaporation of Al, Au, and Pt on n-InP substrate before and after (NH$_{4}$)$_{2}$S$_{x}$ treatments, respectively. The barrier height of InP Schottky contacts was measured by their current-voltage (I-V) and capacitance-voltage (C_V) characteristics. We observed that the barrier heights of Schottky contacks on bare InP were 0.35~0.45 eV nearly independent of the metal work function, which is known to be due to the surface Fermi level pinning. In the case of sulfur-treated Au/InP ar Pt/InP Schottky diodes, However, the barrier heights were not only increased above 0.7 eV but also highly dependent on the metal work function. We have also investigated effects of (NH$_{4}$)$_{2}$S$_{x}$ treatments on the distribution of interface states in Si$_{3}$N$_{4}$InP MIS diodes where Si$_{3}$N$_{4}$ was provided by plasma enhanced chemical vapor deposition (PECVD). The typical value of interface-state density extracted feom 1 MHz C-V curve of sulfur-treated SiN$_{x}$/InP MIS diodes was found to be the order of 5${\times}10^{10}cm^{2}eV^{1}$. This value is much lower than that of MiS diodes made on bare InP surface. It is certain, therefore, that the (NH$_{4}$)$_{2}$S$_{x}$ treatment is a very powerful tool to enhance the barrier heights of Au/n-InP and Pt/n-InP Schottky contacts and to reduce the density of interface states in SiN$_{x}$/InP MIS diode.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.27-27
• /
• 2011

For the design of real applicable molecular devices, current-voltage properties through molecular nanostructures such as metal-molecule-metal junctions (molecular junctions) have been studied extensively. In thiolate monolayers on the gold electrode, the chemical bonding of sulfur to gold and the van der Waals interactions between the alkyl chains of neighboring molecules are important factors in the formation of well-defined monolayers and in the control of the electron transport rate. Charge transport through the molecular junctions depends significantly on the energy levels of molecules relative to the Fermi levels of the contacts and the electronic structure of the molecule. It is important to understand the interfacial electron transport in accordance with the increased film thickness of alkyl chains that are known as an insulating layer, but are required for molecular device fabrication. Thiol-tethered RuII terpyridine complexes were synthesized for a voltage-driven molecular switch and used to understand the switch-on mechanism of the molecular switches of single metal complexes in the solid-state molecular junction in a vacuum. Electrochemical voltammetry and current-voltage (I-V) characteristics are measured to elucidate electron transport processes in the bistable conducting states of single molecular junctions of a molecular switch, Ru(II) terpyridine complexes. (1) On the basis of the Ru-centered electrochemical reaction data, the electron transport rate increases in the mixed self-assembled monolayer (SAM) of Ru(II) terpyridine complexes, indicating strong electronic coupling between the redox center and the substrate, along the molecules. (2) In a low-conducting state before switch-on, I-V characteristics are fitted to a direct tunneling model, and the estimated tunneling decay constant across the Ru(II) terpyridine complex is found to be smaller than that of alkanethiol. (3) The threshold voltages for the switch-on from low- to high-conducting states are identical, corresponding to the electron affinity of the molecules. (4) A high-conducting state after switch-on remains in the reverse voltage sweep, and a linear relationship of the current to the voltage is obtained. These results reveal electron transport paths via the redox centers of the Ru(II) terpyridine complexes, a molecular switch.

• Journal of the Korean Magnetics Society
• /
• v.25 no.5
• /
• pp.156-161
• /
• 2015

The electronic structures of the potential candidate semiconductor nanoparticles for dye-sensitized solar cell (DSSC), such as $ZnSnO_3$ and $Zn_2SnO_4$, have been investigated by employing X-ray photoemission spectroscopy (XPS). The measured X-ray diffraction patterns show that $ZnSnO_3$ and $Zn_2SnO_4$ samples have the single-phase ilmenite-type structure and the inverse spinel structure, respectively. The measured Zn 2p and Sn 3d core-level XPS spectra reveal that the valence states of Zn and Sn ions are divalent (Zn 2+) and tetravalent (Sn 4+), respectively, in both $ZnSnO_3$ and $Zn_2SnO_4$. On the other hand, the shallow core-level measurements show that the binding energies of Sn 4d and Zn 3d core levels in $ZnSnO_3$ are lower than those in $Zn_2SnO_4$. This work provides the information on the valence states of Zn and Sn ions and their chemical bonding in $ZnSnO_3$ and $Zn_2SnO_4$.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.31 no.3
• /
• pp.226-236
• /
• 2021

Objectives: Concerns have been raised about the possible health effects of radon on both workers and consumers with the spread of social attention to the impact of radon exposure. Thus, an entire raw material handling workshop was investigated, and standards for radon levels in the workplace were newly established at 600 Bq/m³. However, regulations on the management of workers exposed to radon are still insufficiently developed. Therefore, by comparative analysis of overseas and domestic radon-related regulations for workplaces, this study aims to suggest improvement plans of protection regulations under the Occupational Safety and Health Act (OSH Act) for the prevention of health disorders of radon-exposed workers. Methods: For overseas case studies, we consulted radon-related laws and reports officially published on the websites of the European Union (EU), the United States (U.S.) and the United Kingdom (UK) government agencies. Domestic law studies were conducted mainly on the Act on Protective Action Guidelines against Radiation in the Natural Environment and the OSH Act. Results: In Europe, the basic safety standards for protection against risks arising from radon (Council Directive 2013/59/EURATOM of 5 December 2013) was established by the EU. They recommend that the Member States manage radon level in workplaces based on this criterion. In the U.S., the standards for workplaces are controlled by the Occupational Safety and Health Administration (OSHA) and the Mine Safety and Health Administration (MSHA). Action on radon in the UK is specified in "Radon in the workplace" published by the Health and Safety Executive (HSE). Conclusions: The Act on Protective Action Guidelines against Radiation in the Natural Environment mainly refers to the management of workplaces that use or handle raw materials but does not have any provisions in terms of protecting naturally exposed workers. In the OSH Act, it is necessary to define whether radon is included in radiation for that reason that its current regulations have limitations in ensuring the safety workers who may be exposed to naturally occurring radon. The management standards are needed for workplaces that do not directly deal with radon but are likely to be exposed to radon. We propose that this could be specified in the regulations for the prevention of health damage caused by radiation, not in Article 125 of the OSH Act.