• Korean Chemical Engineering Research
• /
• v.57 no.6
• /
• pp.861-867
• /
• 2019

$Li_4Ti_5O_{12}$ is a promising next-generation anode material for lithium-ion batteries due to excellent cycle life, low irreversible capacity, and little volume expansion during charge-discharge process. However, it has poor charge capacity at high current density due to its low electrical conductivity. To improve this weakness, porous $Li_4Ti_5O_{12}$ was synthesized by sol-gel method with P123 as chelating agent. The physical characteristics of as-prepared sample was investigated by XRD, SEM, and BET analysis, and electrochemical properties were characterized by cycle performance test, cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS). $Li_4Ti_5O_{12}$ synthesized by 0.01mol ratio of P123/Ti showed most unified particle size, high specific surface area, and relatively high porosity. EIS analysis showed that depressed semicircle size was remarkably reduced, which suggested resistance value in electrode was decreased. Capacity in rate performance showed 178 mAh/g at 0.2C, 170 mAh/g at 0.5C, 110 mA/h at 5C, and 90 mAh/g at 10C. Capacity retention also showed 99% after rate performance.

• Journal of the Korean Electrochemical Society
• /
• v.15 no.1
• /
• pp.19-26
• /
• 2012

SEI (solid electrolyte interphase) layers are generated on a graphite negative electrode from three different electrolytes and low-temperature ($-30^{\circ}C$) charge/discharge performance of the graphite electrode is examined. The electrolytes are prepared by adding 2 wt% of vinylene carbonate (VC) and fluoroethylene carbonate (FEC) into a standard electrolyte solution. The charge-discharge capacity of graphite electrode shows the following decreasing order; FEC-added one>standard>VC-added one. The polarization during a constant-current charging shows the reverse order. These observations illustrate that the SEI film resistance and charge transfer resistance differ according to the used additives. This feature has been confirmed by analyzing the chemical composition and thickness of three SEI layers. The SEI layer generated from the standard electrolyte is composed of polymeric carbon-oxygen species and the decomposition products ($Li_xPF_yO_z$) of lithium salt. The VC-derived surface film shows the largest resistance value even if the salt decomposition is not severe due to the presence of dense film comprising C-O species. The FEC-derived SEI layer shows the lowest resistance value as the C-O species are less populated and salt decomposition is not serious. In short, the FEC-added electrolyte generates the SEI layer of the smallest resistance to give the best low-temperature performance for the graphite negative electrode.

• Korean Chemical Engineering Research
• /
• v.54 no.1
• /
• pp.16-21
• /
• 2016

Silicon/Carbon/CNT composites as anode materials for lithium-ion batteries were synthesized to overcome the large volume change during lithium alloying-de alloying process and low electrical conductivity. Silicon/Carbon/CNT composites were prepared by the fabrication processes including the synthesis of SBA-15, magnesiothermic reduction of SBA-15 to obtain Si/MgO by ball milling, carbonization of phenolic resin with CNT and HCl etching. The prepared Silicon/Carbon/CNT composites were analysed by XRD, SEM, BET and EDS. In this study, the electrochemical effect of CNT content to improve the capacity and cycle performance was investigated by charge/discharge, cycle, cyclic voltammetry and impedance tests. The coin cell using Silicon/Carbon/CNT composite (Si:CNT=93:7 in weight) in the electrolyte of $LiPF_6$ dissolved in organic solvents (EC:DMC:EMC=1:1:1 vol%) has better capacity (1718 mAh/g) than those of other composition coin cells. The cycle performance of coin cell was improved as CNT content was increased. It is found that the coin cell (Si:CNT=89:11 in weight) has best capacity retension (83%) after 2nd cycle.

• Applied Chemistry for Engineering
• /
• v.26 no.1
• /
• pp.80-85
• /
• 2015

Silicon/carbon composites as anode materials for lithium-ion batteries were examined to find the cycle performance and capacity. Silicon/carbon composites were prepared by a two-step method, including the magnesiothermic reduction of SBA-15 (Santa Barbara Amorphous material No. 15) and carbonization of phenol resin. The electrochemical behaviors of lithium ion batteries were characterized by charge/discharge, cycle, cyclic voltammetry and impedance tests. The improved electrochemical performance attributed to the fact that silicon/carbon composites suppress the volume expansion of the silicon particles and enhance the conductivity of silicon/carbon composites (30 ohm) compared to that of using the pure silicon (235 ohm). The anode electrode of silicon/carbon composites showed the high capacity approaching 1,348 mAh/g and the capacity retention ratio of 76% after 50 cycles.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.12
• /
• pp.2226-2230
• /
• 2007

As a cathode material of lithium rechargeable batteries, charged Li[Co0.1Ni0.15Li0.2Mn0.55]O2 electrodes, which were aged thermally at 25 oC and 90 oC respectively, were characterized by means of charge/discharger, impedance spectroscopy, and X-ray diffraction. The discharge capacity diminution of the electrodes aged at 25 oC and 90 oC for 1 week was 4% and 23%, respectively. The cell aged at 25 oC was recovered on cycling. However, the capacity loss after ageing at 90 oC was not recovered in a subsequent cycling test, which demonstrates that the reaction occurring during ageing at 90 oC is irreversible. A significant impedance increase of aged electrode at 90 oC is associated with irreversible capacity loss. The structural changes including phase transformation were not detected by XRD analysis, because it could be due to out of detection limit. After ageing, impedance was slightly decreased during subsequent cycling test. It could be explained the cyclic performance of aged sample is stable. The thermal stability was not deteriorated by ageing even at the high temperature of 90 oC.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.12
• /
• pp.3553-3558
• /
• 2014

The reduced graphene oxide(rGO)/aluminum phosphate($AlPO_4$)-coated $LiMn_{1.5}Ni_{0.5}O_4$ (LMNO) cathode material has been developed by hydroxide precursor method for LMNO and by a facile solution based process for the coating with GO/$AlPO_4$ on the surface of LMNO, followed by annealing process. The amount of $AlPO_4$ has been varied from 0.5 wt % to 1.0 wt %, while the amount of rGO is maintained at 1.0 wt %. The samples have been characterized by X-ray diffraction, scanning electron microscopy, and high-resolution transmission electron microscopy. The rGO/$AlPO_4$-coated LMNO electrodes exhibit better cyclic performance compared to that of pristine LMNO electrode. Specifically, rGO(1%)/$AlPO_4$(0.5%)- and rGO(1%)/$AlPO_4$(1%)-coated electrodes deliver a discharge capacity of, respectively, $123mAhg^{-1}$ and $122mAhg^{-1}$ at C/6 rate, with a capacity retention of, respectively, 96% and 98% at 100 cycles. Furthermore, the surface-modified LMNO electrodes demonstrate higher-rate capability. The rGO(1%)/$AlPO_4$(0.5%)-coated LMNO electrode shows the highest rate performance demonstrating a capacity retention of 91% at 10 C rate. The enhanced electrochemical performance can be attributed to (1) the suppression of the direct contact of electrode surface with the electrolyte, resulting in side reactions with the electrolyte due to the high cut-off voltage, and (2) smaller surface resistance and charge transfer resistance, which is confirmed by total polarization resistance and electrochemical impedance spectroscopy.

• Proceedings of the Korean Fiber Society Conference
• /
• 1996.10a
• /
• pp.124-130
• /
• 1996

The hydrocarbons containing more than 10 carbons(0.1% of total volume, C10+), residue of aromatization from aliphatic hydrocarbons, were condensated in the presence of catalyst aluminumchloride and cocatalyst nitrobenzene(NB) to be pitchs with desirable properties. The properties of pitch were affected by the concentration of cocatalyst chosen 20 and 30wt.%. The pitch with 30wt.% NB showed higher carbon yield and lower crystallinity than that with 20wt.% NB. The two pitches were heat treated at 1000C and measured of charge/discharge capacity of the carbon as an anode. The carbon prepared at 20wt.% NB exhibited excellent cyclic stability with a capacity of 218mAh/.g and that at 30wt.% exhibited rather low cyclic stability with higher capacity of 235mAh/g.

• Journal of the Korean Ceramic Society
• /
• v.49 no.6
• /
• pp.659-662
• /
• 2012

Yttrium (Y) and niobium (Nb) doped spherical $Li_4Ti_5O_{12}$ were synthesized to improve the energy density and electrochemical properties of anode material. The synthesized crystal was $Li_4Ti_5O_{12}$, the particle size was less than $1{\mu}m$ and the morphology was spherical and well dispersed. The Y and Nb optimal doping amounts were 1 mol% and 0.5 mol%, respectively. The initial capacity of the dopant discharge and charge capacity were respectively 149mAh/g and 143 mAh/g and were significantly improved compared to the undoped condition at 129 mAh/g. Also, the capacity retention of 0.2 C/5 C was 74% for each was improved to 94% and 89%. It was consequently found that Y and Nb doping into the $Li_4Ti_5O_{12}$ matrix reduces the polarization and resistance of the solid electrolyte interface (SEI) layer during the electrochemical reaction.

• Resources Recycling
• /
• v.19 no.1
• /
• pp.27-32
• /
• 2010

To improve electronic conductivity of cathodic active materials of lithium ion battery, carbonaceous materials is usually added. New mixing method of abrasive milling has been investigated in mixing of graphite and $LiCoO_2$ powders. It would be expected that uniform mixing of graphite reduces capacity fading of cathode of lithium battery. Abrasion milled $LiCoO_2$ composite showed the best electrochemical performance as a cathode material with 1 wt% of graphite content, 300 rpm of milling speed, and 10 min of milling time. The improvement of the electrochemical performances such as cycleability and charge/discharge capacity retention would be mainly attributed to increase of the electronic conductivity and/or prevention of the active materials by uniform dispersion and coating of graphite on $LiCoO_2$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.378-379
• /
• 2006

The carbon thin film was developed by the CVD method using the carbon source of toluene with the stream of argon gas at $800{\sim}1100^{\circ}C$ for 1 hour. Developed carbon thin films have the material loading of 0.27 mg($800^{\circ}C$), 0.80 mg($900^{\circ}C$), 2.3 mg($1000^{\circ}C$), and 2.9 mg($1100^{\circ}C$) for the disk of 15 mm diameter on single side. The characteristics of carbon thin film as the anode of thin film battery were evaluated using Li|C coin cell. Li|C($1100^{\circ}C$) coin cell has the first specific discharge and charge capacity of 953 mAh/g and 374 mAh/g, respectively, resulting the first Ah efficiency of 39.3 %. Capacity retention of the 5th cycle was 93.2 % indicating good cycleability. The carbon thin film prepared by CVD shows good specific capacity and cycleability, but low Ah efficiency.