• The Research Journal of the Costume Culture
• /
• v.10 no.1
• /
• pp.49-59
• /
• 2002

The type of product and consumer characteristis have known to play an important role in the post-purchase behavior. The issue related to the effects of clothing type and sex on the process of consumer satisfaction formation, would be helpful to understand the past-purchase consumer behavior. Therefore, the objective of this study was to clarify differences in the process of satisfaction formation in relation to clothing type and sex. The study was conducted in three steps. Through the two steps, measurement instruments were developed. At the last step, judgement sampling method was utilized to collect the data and subjects were 614 university students. Factor analysis and path analysis were used to analyze the data. The process of consumer satisfaction formation in formal wear and casual wear showed some differences. In the case of format wear, only expressive product performance was found to play an important role in the process of consumer satisfaction formation. However in the case of casual wear, both expressive and instrumental product performances had influence upon clothing satisfaction directly or through consumption emotion. The results revealed a similar tendency in the process of satisfaction formation between male and female groups. However in the male group the consumption emotion had a greater effect on the process of consumer satisfaction formation than in the female group it did.

• Water for future
• /
• v.27 no.2
• /
• pp.63-72
• /
• 1994

In this study, hydraulic characteristics for upstream migration of fish in a pool-and-weir fishway were analyzed through experiment. The results showed that streaming flow was preferable to plunging flow for upstream migration of fish and it was not good to make an orifice beneath the septum since it generates turbulent jet and eddies. Protrusions on the side wall of fishway were preferable to grooves since they decelerate flow velocity and make upstream migration easy. A vertically movable septum was necessary for a flushing of deposited bed material, and net installing over fishway was also needed for birds not to approach the fishway and eat fish.

• Journal of Fashion Business
• /
• v.3 no.4
• /
• pp.113-129
• /
• 1999

The purpose of this study is to discover the changes and characteristis of modern knitwears from the 1920's to the 1990's. The result of this study is as follows: The popular knitwears in the 1920's had a simple boxy-line and modern unisex image with a sporty look. The knitwears in the 1930's-1950's had seen more short, feminine detail and texture, fit silhouette with syntheyic fibers. In the 1960's, the knitwears of sporty look and unisex style was popularized by young peaples, and crochet with handkniting by the fiber artists was popularized. In the 1970's-80's, the layered looks and unisex styles of knitwears were popularized by influence of a ecology mood and a woman movemant. And various patterns was developed with the computer machine. The items of outer knitwear was increased by the use of fancy yarns and the knitwears as the total fashion was popularized. In the 1990s, the knitwears had a very forceful characteristics by the mixed style and the technique of design developed into the post-modernism. The key words of the character of the modern knitwears are funtional pursuit, unisex, high value, hightechnique, art. By the change of the life style and the develope of technical innovation, the knitwears will be the key item to leading the fashion in the 21th.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.18 no.2
• /
• pp.27-35
• /
• 1981

In this study, a numerical theory based on space charge overlapping model and experiments on the propriety of its theory were carried out to analyze the switching transient characteristic in amorphous coalcogenide thin film. Theoretical and experimental as well as analytical investigations were carried out on the switching behaviour in a transient state arising from a voltage pulse applied to amorphous chalcogenide thin films at room temperature. The results can be explained in terms ot a simple theoretical model of the electronic characteristics of switching. The injection of carriers are necessary to initiate the switching action and injected carriers contribute to the current flow as a space-charge limited current(SCLC) The proposed charge controlled switching characteristics can be explained by double injection space charge overlapping model.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.5
• /
• pp.412-418
• /
• 2002

In this paper, the authors present the simulation results and the experimental considerations on the effects of the effects of the VCO oscillation characteristics caused by varying the length of the MSL and the composition capacitance of LC resonation circuity. Simulation was accomplished by nonlinear RF circuit simulator for designing and analyzing the RF characteristis of VCO. The samples with 3 different MSL lengths of which the length is 140mil, 280mil and 560mil respectively were fabricated by screen printing process. The oscillation frequency of each sample(VCO) was tuned to UHF band (750MHz~900MHz) by varying the capacitance of LC resonator circuit. The experimental results showed that the values of phase noise were -82, -93, -97[dBc/Hz] at 50[kHz] offset frequency, the pushing figures were 114, 94, 318[kHz] at applied voltage of $3\pm0.15$[V] and the harmonics were -21, -16, -13[dBc] for MSL lengths of 140mil 280mil, 560mil respectively. The frequency and output variation width were 779~898[MHz], -36~-33[dBm] for MSL with 140mil length; 818~836[MHz], -27.19~27.06[dBm] for 280mil; 751.54~751.198[MHz], -33.44~-33.31[dBm] for 560mil.

• Korean Journal of Materials Research
• /
• v.16 no.11
• /
• pp.710-714
• /
• 2006

The purpose of this study is to identify the effect of additives and composition on copper surface morphology and mechanical characteristics by copper electrodeposition. Additives such as hydroxy ethyl cellulose(HEC), chloride ion were used in this study. Electrochemical experiments allied to SEM, XRD, AFM and four- point probe were performed to characterize the morphology and mechanical characters of copper in the presence of additives. Among various electrodeposition conditions, the minimum surface roughness of copper foil was obtained when electrodeposited at the current density of 200 mA/$cm^2$ for 68 seconds with 2 ppm of HEC. The minimum value of surface roughness(Rms) was 107.6 nm. It is copper foil is good for electromigration inhibition due to preferential crystal growth of Cu (111) deposited in the electrolyte containing chloride ions(10 ppm) and HEC(1 ppm).

• Journal of the Korean Association of Geographic Information Studies
• /
• v.3 no.3
• /
• pp.1-11
• /
• 2000

This study was analysed the characteristis of traveling vehicles using the collected data by DGPS receiver. These data were checked the vehicle position in every 2 seconds and compared with GIS digital map after correcting the errors. These are compared travel speed and running speed overall and analysed the stopping vehicle in the middle of travelling. The stopping frequency, stopping time and stopping factor was analysed. The X, Y coordinates positioning of DGPS received data about stopping vehicle was analysed. DGPS receiver didn't position at first but positioned it exactly as time went. This study carried out the basic study about travel characteristics with digital map and DGPS received data. Few studies which applied advanced technology like GIS & DGPS have been executed. I hope that the more study will be executed in this traffic field.

• The Journal of Fisheries Business Administration
• /
• v.27 no.1
• /
• pp.15-45
• /
• 1996

The sustained economic growth cannot be expected without the balanced development in all the realms of industries. Korea has recorded the continuous high growth rate of economy, but it is now facing some difficulties in keeping the normal economic growth, because industrial workers do not like to work in some fields, the typical one of which is the fishery works. This thesis aims at studying the determinants of fishermen's job satisfaction(FJS) and the determinants of affecting the fishermen's trunover intention(FTI) to obtain and maintain the man power for fishing boats. This study assumes that the determinants which affact FJS are fishermen's work values, job characteristics, the attitude of accepting their fishery work, and that the determinants which affect FTI are FJS and their perceptions of labor market. This study concerns two kinds of Job satisfaction : one is an intrinsic satisfaction which comes directly from the work itself, and the other is an extrinsic satisfaction comes from the compensation for the work, but in this study “Pollnac's work satisfaction factor” is added as an additional determinant of FJS. There is a difference in job satisfactions between the individuals who have different work values. Some feel more satisfacttion than the others, which can be explained by the internal work values which assume the work is only a means for another objective of life. This study applies Hackman and 014ham's studies to the job characteristics that a worker's job satisfaction is positively related to the core job characteristis of the job. In addition, this study transformed their studies into variables. A job enrichment to reduce the simplicity of a work and make it more valueable can increase a job satisfaction, but an existing organization has limitation in redesigning the job for its enrichment. A reasonable answer about this matter can be obtained from the workers' subjective perceptins to highly regard the objective job characteristics. Worker's previews of fishery work also affect their job satisfaction because they are already informed of the details and charcteristics of the job that they have to carry out. A Job dissatisfaction causes their intention to leave jobs owing to general perceptions prevailing in labor markets.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.2 no.1
• /
• pp.75-82
• /
• 1988

Epoxy, noticed as a new insulation material tor electrical installation, may become an excellent cured material from the crosslink reaction with some curing agents. The characteristics of cured Epoxy is determined by the kind of the curing agents and the method of lattice formation. The purpose of this paper, varing the process of lattice formation by various surrounding temperatures during the curing process, is to obtain the optimum curing temperature for electrical insulation from the results of investigation on the properties of cured Epoxy. In the experiment, Epoxy was cured at various temperatures between $20[^{\circ}C] and 50^[{\circ}C]$ which differ by $5^[{\circ}C]$, and then examined on the electrical insulation haracteristics as well as the thermal and mechanical stability. As a result, it is concluded that the optimum electrical insulation characteristis and mechanical strength of cured Epoxy can be obtained when cured at a surrounding temperature at $30[^{\circ}C]$.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.2
• /
• pp.10-16
• /
• 2003

The unsteady supersonic flow over tandem cavities has been analyzed by the integration of Navier-Stokes equations with the k-$\varepsilon$ turbulence model. The unsteady flow is characterized by the periodicity due to the mutual relation between the shear layer and the internal flow in cavities. The upwind TVD scheme based on the flux vector split with the van Leer limiters is used. The results show the principal frequency is very reasonable. The principal frequency of the rear cavity due to the front cavity has been analyzed by the combination of the several aspect ratios of cavities. In the case of the front cavity of low aspect ratio, the frequencies of tandem cavities are almost same, because two shear layers developed from each cavity are mixed and developed to one shear layer. However, in the case of the front cavity of high aspect ratio, the characteristis of frequency are very different, because the second shear layer is developed in the diffused first shear layer.