• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2004년도 전력전자학술대회 논문집(1)
• /
• pp.117-120
• /
• 2004

As the maximum power operating point (MPOP) of photovoltaic (PV) power generation systems changes with varying atmospheric conditions such as solar radiation and temperature, an important consideration in the design of efficient PV system is to track the MPOP correctly. Although the efficiency of these Maximum Power Point Tracking algorithms is usually high, it drops noticeably in case of rapidly changing atmospheric conditions. This paper describes common MPPT control algorithm: Constant Voltage Control, Perturbation and Observation(P&O), Incremental Conductance (IncCnd) and proposes a new MPPT algorithm based on P&O algorithm. The conception and control principles of the proposed MPPT method are explained in detail and its validity of the proposed method is verified through several simulated results. As it doesn't use digital signal processor, this MPPT method has the merits of both a cost efficiency and a simple control circuit design. Therefore, it is considered that the proposed MPPT method is proper to low power, low cost PV applications.

• 한국정밀공학회지
• /
• 제13권1호
• /
• pp.69-77
• /
• 1996

To design high-effective profile in screw rotor profile using in screw compressor, we design the symmetric type changing the number of lobes and the non-symmetric type changing the neighbourhood of the top point of lobe. Then, we calculated the performance value of profile according to the scale of these non-symmetric's wrap angle. We had the results as follows. 1. About the non-symmetric case, the larger a wrap angle is the shorter seal line is and the smaller blow hole is, thus we know what the large wrap angle profile is better than the small one. 2. We know what the non-symmetric profile is better than the symmetric profile in the result of the compare of seal line's length, blow hole's area, volume curve. 3. About the non-symmetric case, the deformation of the neighbourhood of lobe's top point of the rotor profile has a large effect upon the increase of performance because the length of seal line became short and the area of blow hole is small.

• 조명전기설비학회논문지
• /
• 제28권11호
• /
• pp.17-25
• /
• 2014

This paper proposes a novel maximum power point tracking (MPPT) system using a fuzzy logic control (FLC) algorithm for robust in-environment changing. The power available at the output of a photovoltaic (PV) cell continues to change with radiation and temperature because a solar cell exhibits nonlinear current-voltage characteristics. Therefore, the maximum power point (MPP) of PV cells varies with radiation and temperature. The MPPT methods are used in PV systems to make full utilization of the PV array output power, which depends on radiation and temperature. The conventional MPPT control methods such as constant voltage (CV), perturbation and observation (PO) and incremental conductance (IC) have been studied but these methods are problematic in that they fail to take into account the changing environment. The proposed FLC controller is based on the fuzzy control algorithm and facilitates robust control with the environmental changes. Also, the PV systems applied FLC controller is modeled by PSIM and the response characteristics of the FLC method according to environmental variations are analyzed through comparison with the performance of conventional methods. The validity of this controller is shown through response results.

• 센서학회지
• /
• 제18권3호
• /
• pp.185-189
• /
• 2009

In this paper, we present design and analysis of the omni-directional linear piezoelectric actuator which was consisted of one actuator using the half-wave vibrator. Through calculating vibration speeds on each sector of the actuator, the displacement of contact point of the actuator is theoretically confirmed to be about 33 nm. To confirm an applicable possibility of omni-directional linear piezoelectric actuator, elliptical motion for linear movement, displacement of the tip, changing directions and admittance characteristics are simulated by ATILA. Compared with theoretical result, we obtained similar data with displacement of 32.5 nm at contact point. And then the actuator is simulated elliptical trajectories for linear motions and changing directions according to combination of input signal.

• Journal of applied mathematics & informatics
• /
• 제28권5_6호
• /
• pp.1171-1184
• /
• 2010

In this paper, by using fixed point theorems in cones, the existence of positive solutions is considered for nonlinear m-point boundary value problem for the following second-order dynamic equations on time scales $({\phi}(u^{\Delta}))^{\nabla}+a(t)f(t,\;u(t))=0$, t $\in$ (0, T), $u(0)=\sum\limits^{m-2}_{i=1}a_iu(\xi_i)$, $\phi(u^{\Delta}(T))=\sum\limits^{m-2}_{i=1}b_i{\phi}(u^{\Delta}(\xi_i))$, where $\phi$ : R $\rightarrow$ R is an increasing homeomorphism and positive homomorphism and ${\phi}(0)=0$. In [27], we obtained the existence results of the above problem for an increasing homeomorphism and positive homomorphism with sign changing nonlinearity. The purpose of this paper is to supplement with a result in the case when the nonlinear term f is nonnegative, and the most point we must point out for readers is that there is only the p-Laplacian case for increasing homeomorphism and positive homomorphism due to the sign restriction. As an application, one example to demonstrate our results are given.

• 한국산업융합학회 논문집
• /
• 제7권2호
• /
• pp.153-159
• /
• 2004

The purpose of this research is to investigate the performance of swirl combustion chamber diesel engine by changing the jet passage area, the depth and shape of the piston top cavity (main chamber). The performance of diesel engine with newly changed swirl combustion chamber was tested through the experimental conditions as engine speed, load and injection timing etc. The test results were compared and analyzed. And another purpose of this research is to make a new diesel engine that is satisfied fuel consumption and regulation value of exhaust gas. 1. The rate of fuel consumption was affected significantly by the jet passage area at the high speed and load than low speed and low load. The influence of jet passage large area was proven to decrease the rate of fuel consumption. 2. Smoke was affected significantly by the depth of the piston top cavity, but exhaust temperature and the rate of fuel consumption wasn't affected. The rate of fuel consumption was affected by changing injection timing. 3. The rate of fuel consumption, exhaust temperature and Smoke were affected significantly by the shape of the piston top cavity from rectangular to trapezoid. That is we have all high value. The exhaust smoke density and exhaust gas temperature depended sensitively on variation of the injection timing rather than the shape of the combustion chamber within the experimental conditions. 4. We made a new diesel engine that is satisfied design target values(sfc=190 g/hr, NOx + THC=6.0 g/KWh, PM=0.3 KWh), the rate of fuel consumption and emission standard etc., through changing injection timing at the maximum torque point and rated power point. Although we have a little high NOx value.

• Spatial Information Research
• /
• 제6권1호
• /
• pp.11-23
• /
• 1998

GIS 분야에서 지도 일반화는 공간자료의 상세도를 결정하여 효과적으로 자료를 가시화(Visualixation)하거나 자료의 해상력을 변화시켜 변환하는 기능을 수행한다. 최근까지 지도 일반화는 선사상 (Line Features)에 집중되었고, 수치지도를 구성하고 있는 정보량과 그 중요성에 비하여 점사상 (Point Features)에 대한 연구는 상대적으로 미미하였다. 이러한 맥락에서 본 연구는 점사상에 대한 구체적인 일반화 방안을 모색하는데 목적을 둔다. 특히 점사상의 일반화에서 원자료의 기하학적 특성을 파악하는데 가장 중요하게 고려한 요소로 점사상의 분포패턴을 선정하였다. 즉 'Grieg-Smith방법'을 활용한 방격분석 (Quadrat Analysis)과 최근린분석 (Nearest-Neighbour Analysis)를 통해 점사상이 갖고 있는 분포패턴의 특성을 찾아낸 다음, 이를 변형시키지 않도록 일반화의 기준거리(Threshold)를 설정하여 점사상을 제거하는 방법을 통해 점사상의 일반화를 시도하였다. 따라서 이 연구에서 제시한 점사상의 일반화 방안은 원래 점사상이 갖고 있는 기하학적 특성을 최대한 유지한다.

• Journal of applied mathematics & informatics
• /
• 제30권3_4호
• /
• pp.517-529
• /
• 2012

In this paper, the existence theorem of two positive solutions is established for nonlinear m-point boundary value problem by using an inequality for the following third-order differential equations $$({\phi}(u^{\prime\prime}))^{\prime}+a(t)f(t,u(t))=0,\;t{\in}(0,1)$$, $${\phi}(u^{\prime\prime}(0))=\sum^{m-2}_{i=1}a_i{\phi}(u^{\prime\prime}({\xi}_i)),\;u^{\prime}(1)=0,\;u(0)=\sum^{m-2}_{i=1}b_iu({\xi}_i)$$, where ${\phi}:R{\rightarrow}R$ is an increasing homeomorphism and homomorphism and $\phi(0)=0$. The nonlinear term f may change sign, as an application, an example to demonstrate our results is given.

• Journal of Power Electronics
• /
• 제14권1호
• /
• pp.156-164
• /
• 2014

The power-voltage (P-V) characteristic of a photovoltaic (PV) array is nonlinear and time varying with the change in atmospheric conditions. As a result, the maximum power point tracking (MPPT) technique must be applied in PV systems to maximize the generated energy. The incremental conductance (INC) algorithm, one of the MPPT strategies, is widely used for its high tracking accuracy, good adaptability to rapidly changing atmospheric conditions, and easy implementation. This paper presents a modified asymmetrical variable step size INC MPPT method that is based on the asymmetrical feature of the P-V curve. Compared with conventional fixed or variable step size method, the proposed method can effectively improve tracking accuracy and speed. The theoretical foundation and design principle of the proposed approach are validated by the simulation and experimental results.

• 대한기계학회논문집
• /
• 제6권4호
• /
• pp.301-307
• /
• 1982

The purpose of this investigation is to study heat transfer characteristics at a stagnation point on a flat plate caused by upward impinging water jet. At the stagnation point, heat transfer results by impinging water jet are being compared with the ones with supplementary water. Optimum supplementary water quantity are supplied in order to improve the effect of heat transfer for each nozzle-to-plate distance. As the nozzle outlet velocity increases, the heat transfer coefficient at stagnation point consequently increases. Changing the nozzle-to-plate distance, growth rate of heat transfer also varies accordingly. This optimum range of Reynolds number is obtained to improve heat transfer effect.