• Structural Engineering and Mechanics
• /
• v.11 no.4
• /
• pp.393-406
• /
• 2001

The present paper discusses the behavior of the reinforced concrete beams subjected to torsion by applying the endochronic plastic model in conjunction with the softened truss model. The endochronic constitutive equations are developed to describe the behavior of concrete. The mechanical behavior of concrete is decomposed into hydrostatic part and deviatoric part. New definition of the bulk modulus and the shear modulus are defined in terms of compressive strength of concrete. Also, new deviatoric hardening function is developed. Then, the endochronic constitutive equations of concrete are applied with the softened truss model for the behavior of the reinforced concrete beams subjected to torsion. The theoretical results obtained based on the present model are compared with the experimental data. The present model has shown the ability to describe the behavior of reinforced concrete beams subjected to torsion.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.36 no.4
• /
• pp.266-272
• /
• 2016

This paper presents the investigation of the propagation behavior of bulk longitudinal waves generated by an ultrafast laser system in thin films. A train of femtosecond laser pulses was focused onto the surface of a 150-nm thick metallic (chromium or aluminum) film on a silicon substrate to excite elastic waves, and the change in thermoreflectance at the spot was monitored to detect the arrival of echoes from the film/substrate interface. The experimental results show that the film material characteristics such as the wave velocity and Young's modulus can be evaluated through curve-fitting in numerical solutions. The material properties of nanoscale thin films are difficult to measure using conventional techniques. Therefore, this research provides an effective method for the nondestructive characterization of nanomaterials.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1690-1695
• /
• 2007

Lightweight metallic truss structures with open, periodic cell are currently being investigated because of their multi-functionality such as thermal management and load bearing. The Kagome truss PCM has been proved that it has higher resistance to plastic buckling, more plastic deformation energy and lower anisotropy than other truss PCMs. The subject of this paper is an examination of the failure mechanism of Wire woven Bulk Kagome(WBK). To address this issue, the out-of-plane compressive responses of the WBK has been measured and compared with theoretical and finite element (FE) predictions. For the experiment, 2 multi-layered WBK are fabricated and 3 specimens are prepared. For the theoretical analysis, the brazed joints of each wire in WBK are modeled as the pin-joint. Then, the peak stress of compressive behavior and elastic modulus are calculated based on the equilibrium equation and energy method. The mechanical structure with five by five cells on the plane are constructed is modeled using the commercial code, PATRAN 2005. and the analysis is achieved by the commercial FE code ABAQUS version 6.5 under the incremental theory of plasticity.

• Journal of Biosystems Engineering
• /
• v.26 no.1
• /
• pp.47-56
• /
• 2001

In order to prevent the possibility of mixing of metal powder during food grinding processing with the metal roll mill this study was conducted to develope the materials of ceramics roll as a substitute of gray cast iron mill. Since the ceramics is brittle material and can be broken easily by a crack, it was needed to develope engineering ceramics roll materials with high elastic modulus and fracture toughness. Adding 0∼50 wt% Al$_2$O$_3$as densification additives to porcelain body material and forming the ceramics an different condition, mechanical properties were evaluated. The material structure’s densification process was analyzed by SEM and XRD. The evaluation of the mechanical properties of ceramics roll materials were compared and analyzed by non-destructive test using Young’s modulus and destructive test using 3-point bending strength and fracture toughness. The results showed several correlative results. Porcelain body material with 40 wt% Al$_2$O$_3$content heated at 1,200$\^{C}$ for 5h was high bulk density of 2.77, Young’s modulus of 118.4Gpa, 3-point bending strength of 137 MPa and fracture toughness of 2.88 MPa$.$m$\^$$\sfrac{1}{2}$/ . After analyzing the relationship between non-destructive test and destructive test, the coefficient of determination was more than 0.9. Therefore, the evaluation of non-destructive test by ultrasonic was turned out to be feasible in evaluating the mechanical properties of ceramics.

• Proceedings of the KSR Conference
• /
• 2008.06a
• /
• pp.1712-1723
• /
• 2008

In the trackbed design using an elastic multi-layer model, the stress-dependent resilient modulus is the key input parameter, which reflects substructure performance under repeated traffic loading. The prediction models of resilient modulus of crushed stone and weathered granite soil were developed from nonlinear dynamic stiffness, which can be combined by in-situ and laboratory seismic measurements. The models accommodate the variation with the deviatoric and/or bulk stresses. To investigate the performance of the prediction models proposed, the elastic response of the test trackbed near PyeongTaek, Korea was evaluated using a 3-D nonlinear elastic computer program (GEOTRACK) and compared with measured elastic vertical displacement caused by the passages of freight and passenger trains. The material types of the test sub-ballasts are crushed stone and weathered granite soil, respectively. The calculated vertical displacements within the sub-ballasts are within the order of 1mm, and agree well with measured values with the reasonable margin. The prediction models are thus concluded to work properly in the preliminary investigation.

• Structural Engineering and Mechanics
• /
• v.38 no.3
• /
• pp.361-384
• /
• 2011

Earlier studies on hollow-circular rubber bearings, all of which are conducted for steel-reinforced bearings, indicate that the hole presence not only decreases the compression modulus of the bearing but also increases the maximum shear strain developing in the bearing due to compression, both of which are basic design parameters also for fiber-reinforced rubber bearings. This paper presents analytical solutions to the compression problem of hollow-circular fiber-reinforced rubber bearings. The problem is handled using the most-recent formulation of the "pressure method". The analytical solutions are, then, used to investigate the effects of reinforcement flexibility and hole presence on bearing's compression modulus and maximum shear strain in the bearing in view of four key parameters: (i) reinforcement extensibility, (ii) hole size, (iii) bearing's shape factor and (iv) rubber compressibility. It is shown that the compression stiffness of a hollow-circular fiber-reinforced bearing may decrease considerably as reinforcement flexibility and/or hole size increases particularly if the shape factor of the bearing is high and rubber compressibility is not negligible. Numerical studies also show that the existence of even a very small hole can increase the maximum shear strain in the bearing significantly, which has to be considered in the design of such annular bearings.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.36 no.6
• /
• pp.474-482
• /
• 2016

A Kelvin foam plate - widely used in the energy and transport industries as a lightweight structural material - was examined to estimate its Young's modulus using ultrasound. An isotropic tetrakaidecahedron foam structure was designed in SolidWorks and printed using 3D printer with an ABS plastic material. The 3D printed foam structure was used to build a foam plate with a 14 mm thickness ($50mm{\times}100mm$ in size) for the ultrasonic test. The Kelvin foam plate, a significantly porous medium, was completely filled with paraffin wax to enable the ultrasound to penetrate through the porous medium. The acoustic wave velocity of the wax-filled Kelvin foam was measured using the time of flight (TOF) method. Furthermore, the elastic modulus of the Kelvin foam was estimated based on an elastic structural model developed in this study. The Young's modulus of the produced Kelvin foam was observed to be approximately 3.4% of the bulk value of the constituent material (ABS plastic). This finding is consistent with experimental and theoretical results reported by previous studies.

• Textile Coloration and Finishing
• /
• v.4 no.1
• /
• pp.26-29
• /
• 1992

Ternary solutions that cellulose triacetate (CTA) and polyethylene terephthate (PET) were mixed in a solvent trifiuoroacetic acid (TFA)/methylene chloride (MC) (6/4 : v/v) showed phase separation and mesophase formation. The ternary systems which were mesomorphic were spun into a methanol both and relatively strong cellulosic fillaments were successfully produced. Analysis showed that CTA/PET fibers have fibrillar structure and high orientation parallel to the fiber axis. These fibers proved to be molecular composite and have relatively high strength and modulus as spun.

• Korea-Australia Rheology Journal
• /
• v.18 no.3
• /
• pp.127-131
• /
• 2006

Few investigations of bread dough compressibility have been reported in the literature, despite the fact that high compression stresses are often reached in processing. Here we report some experiments on the compressibility of an Australian wheat bread dough under compressive stresses up to 5 MPa, and show that the results are consistent with a mathematical model of bread dough containing entrained air. The implications for tensile testing are also considered.

• Journal of the Korean Ceramic Society
• /
• v.22 no.5
• /
• pp.66-70
• /
• 1985

This study was to investigate physical properties of the system $Ca(Mg_{1-x}Al_x) (Si_{2-x}Al_x)O_6$ by quenching method. This system $\chi$=0.1 to 0.3 had same crystal phase microstructure and similar properties. Bulk density microhardness thermal expansion coefficient and modulus of rupture of these solid solutions were 2.87~2.95g/cm3 850~900kg/$mm^2$, $7.5~7.8{\times}10^{-6}$/$^{\circ}C$ and 1950~1980kg/$cm^2$ respectively.