• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2006.05a
• /
• pp.39-42
• /
• 2006

Recently, more highly effective construction materials are needed for the reasonable and economical structure system is required as the construction structures become more multi storied, large-sized and diversified. That is to say, the highly qualified concrete, the molt universal construction material is positively promoted as a part of plan to establish the effective space according to the dead load of structures and diminish of segment profile and to build up the economic structures. In particular, it is tendency of that the study for high strength concrete increases and construction example of reinforced concrete (RC) using the high strength concrete partially increases. However, the high strength concrete has the problems such high brittleness and low ductility. Specially, for the high strength concrete, it has different strength from normal concrete as the internal temperature goes up steadily due to high heat of hydration by the quantities of highly level of cement, so the concrete which is mixed with various scible materials is used. This study conducted a basic experiment to conclude an adequate selection of materials and to calculate an optimal mixing proportion of those materials to produce High-strength concrete. And also we conducted an experiment to find out basic properties of this concrete such as slump-flow, strength.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2023.05a
• /
• pp.213-214
• /
• 2023

Positioning information of workers is important for safety management at construction sites. Among the various indoor positioning technologies, geomagnetic fields-based technology is more economical and has less error than other technologies. However, there is a problem that the installation and dismantling of materials such as formwork at construction sites can cause degradation in positioning performance. Therefore, in this study, the distortion of the geomagnetic field near euro-form was quantitatively measured and the application method of geomagnetic field-based indoor positioning technology on formwork stage was presented. The results showed that the distortion occurred within 10cm of the wall and column form, but positioning accuracy could be affected up to 60cm from the form due to the characteristic of geomagnetic field-collecting technology. Therefore, applying this technology to the formwork stage requires complementary measures, such as using other positioning techniques up to 60 cm near the formwork, or excluding distorted area when positioning. It is expected that this study can contribute to the efficient safety management of workers by suggesting ways to prevent an increase in positioning error when applying geomagnetic field sequence-based indoor positioning technology during the formwork stage.

• Journal of Korean Society of Rural Planning
• /
• v.19 no.1
• /
• pp.189-207
• /
• 2013

This study aimed to draw the plan elements and characteristics that should be considered in case when developing guidelines to build up roads in rural villages. Drawing the construction elements necessary for building up roads through the advanced researches, the survey was conducted for relevant experts in order to evaluate the importance of each plan element of route plan, design & construction and operation & management. The result determined total 105 contents that should be considered in case when building up roads in rural villages. The study on building up roads in rural villages as a strategy to vitalize rural areas means universal roads that connect each village with rural amenities in various values like walking tour road, visit roads and observation roads. It is considered that the development of guidelines for building up roads in rural villages could be used as a basic data to build up roads where nature, culture and history of rural areas can be effectively experienced and enjoyed.

• International conference on construction engineering and project management
• /
• 2009.05a
• /
• pp.1491-1496
• /
• 2009

Because of the development of advanced construction technology, the inner environments of building become more and more complicated, which may result in many problems. The administer may forget where they put up the certain picture, and search for it all over the building, or they underestimate the number of the visitors, and find the situation is out of control, while the pedestrian may get lost, and after making their efforts, they found they turned back to the origin point again. So it is very necessary to establish an indoor spatial database. On one hand, it is able to assist administrator to manage the property and human flow inside the building, on the other hand it could help the pedestrian find the way easily especially when they are not familiar with the building or there is an emergency. This paper focused on how to create the indoor spatial database including both static database and moving objects database. The static database is built on the basis of 3D building models, and the moving objects database gets information from many kinds of cameras and sensors installed in the building. And at the same time the paper discussed the practical use of indoor spatial database mainly in three aspects including consistency management, building restructure, and pedestrian navigation.

• Journal of architectural history
• /
• v.16 no.3
• /
• pp.57-74
• /
• 2007

Jeoksimto which was build up as the reinforcement establishment made with the soil under the cornerstone in the site of tile-capped building is the representative construction technique which become popular in the Sabi capital era after the Wungjin capital era. Especially from the fact that no site of tile-capped building with this Jeoksimto has been found in the Silla area, we can see the originality Baekje technique. We can analogize the specialization of Josagong (造寺工) (craftsman building the temple) and the diversity of technique, on the basis of the technique raising the ground level which is different with the middle gate site of Neung-sa and the Hall enshrining Buddha site in Buyeo. Moreover, we can have the confidence the dispatch of craftsman and the transmission of building technique from the Buyeo area to the Iksan area through the fact that the construction techniques of Jeoksimto in both area are almost the same. However the concerns in the construction archaeology are necessary because almost no study for Jeoksimto has been conducted and the term of Jeoksimto also is unfamiliar even if excavation of Baekje Jeoksimto in the several remains.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.405-410
• /
• 2009

This paper presents a case study that achieved both of serviceability and safety of the building through soil reinforcement and restoration around foundations subjected to serious differential settlement using D-ROG method. The building which has one basement floor and three ground floors is founded on soft ground and differential settlement occurred to the maximum extent of 678mm. The foundation type of the building is a independent mat foundation. Soil profiles consist of landfill layer, alluvial layer, weathered rock, and soft rock. The bearing layer consisting of gravel and weathered rock is located 16.0~17.0m below the bottom of the building. As a result of soil reinforcement and restoration, the recovery ratio of more than 90% can be attained with the maximum set-up of 657mm.

• Journal of the Korea Institute of Building Construction
• /
• v.10 no.6
• /
• pp.137-143
• /
• 2010

Target Costing is a modern cost management technique used in changeable market conditions. The target cost is set by subtracting the sum of production costs and profits from the market price. The purpose of this present study is to review Target Costing as a useful concept which integrates the project development process with cost management. "Minimum Waste, Maximum Value" could be achieved by setting up guidelines for optimal building design at the beginning of the project development phase. This effective budget management method will help rectify Korea's overspending problems in the area of government building construction projects.

• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.35 no.7
• /
• pp.187-195
• /
• 2019

In December 2015, The Paris Agreement was adopted to undertake ambitious efforts to combat climate change. Korean government announced its goal of reducing the country's greenhouse gas emissions by up to 37% below business as usual projections by 2030 in 2015. The purpose of this study was to set up the calculation methodology of GHG emission($CO_{2e}$) in building sector and to estimate the annual GHG emission in building sector based on national energy consumption statistic. The GHG emission from buildings is about 135.8 million ton $CO_{2e}$ as of 2015, taking up about 19.6% of Korea's entire emission and is about 144.7 million ton $CO_{2e}$ in 2017. The GHG emission of building sector is increasing at annual rate of 2.0% from 2001 to 2017. The GHG emission from electricity consumption in buildings is 91.8 million ton $CO_{2e}$ in 2017, is the highest $CO_2$ emission by energy source. The results show that the intensity of GHG emission of residential building sector is $40.6kg-CO_{2e}/m^2{\cdot}yr$ and that of commercial building sector is $68.4kg-CO_{2e}/m^2{\cdot}yr$.

• Korean Journal of Construction Engineering and Management
• /
• v.25 no.3
• /
• pp.37-46
• /
• 2024

Recently, 3D laser scanning technology, which can collect accurate and quick information on phenomena, has been attracting attention among smart construction technologies. 3D laser scanning technology can obtain information most similar to reality at construction sites. In this study, we would like to apply a new member identification method to an actual building and present the possibility of applying point cloud data, which can be collected using 3D laser scanning technology, to measuring progress at construction sites. In order to carry out the research, we collected location information for component identification from BIM, set a recognition margin for the collected location information, and proceeded to identify the components that make up the building from point cloud data. Research results We confirmed that the columns, beams, walls, and slabs that make up a building can be identified from point cloud data. The identification results can be used to confirm all the parts that have been completed in the actual building, and can be used in conjunction with the unit price of each part in the project BOQ for prefabricated calculations. In addition, the point cloud data obtained through research can be used as accurate data for quality control monitoring of construction sites and building maintenance management. The research results can contribute to improving the timeliness and accuracy of construction information used in future project applications.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.05a
• /
• pp.24-25
• /
• 2014

Up to now, most the fenestration industry is consisted of glazing and window frame in Korea. According to the Fenestration Energy Consumption Efficiency Rating System and Energy Saving Design Standards of Buildings, u-value of fenestration is defined as the value of calculation with glazing and frame. For this reason, when applying for a building permit, in most cases, the official approval test report of the set of windows and doors is used. Nevertheless, in windows construction progresses, most construction manager take delivery of the glazing and frame separately. For those reason, windows and doors are constructed regardless of the report of the Fenestration Energy Consumption Efficiency Rating System in most construction fields. From now on, the research of the connection method between reality of policy and reality of construction fields should be carried out.