• Tribology and Lubricants
• /
• v.40 no.4
• /
• pp.133-138
• /
• 2024

This study evaluates the structural safety of wind turbine blades, analyzes the behavior of composite laminate structures with and without defects, and assesses surface erosion wear. The NREL 5 MW standard is applied to assign accurate composite material properties to each blade section. Modeling and analysis of the wind turbine blades reveal stable behavior under individual load conditions (gravity, motor speed, wind speed), with the web bearing most of the load. Surface erosion wear analysis in which microparticle impacts are simulated on the blade coating shows a maximum stress and maximum displacement of 14 MPa and 0.02 mm, respectively, indicating good initial durability, but suggest potential long-term performance issues due to cumulative effects. The study examines defect effects on composite laminate structures to compare the stress distribution, strain, and stiffness characteristics between normal and cracked states. Although normal conditions exhibit stable behavior, crack defects lead to fiber breakage, high-stress concentration in the vulnerable resin layer, and decreased rigidity. This demonstrates that local defects can compromise the safety of the entire structure. The study utilizes finite element analysis to simulate various load scenarios and defect conditions. Results show that even minor defects can significantly alter stress distributions and potentially lead to catastrophic failure if left unaddressed. These findings provide valuable insights for wind turbine blade safety evaluations, surface protection strategies, and composite structure health management. The methodology and results can inform the design improvements, maintenance strategies, and defect detection techniques of the wind energy industry.

• Journal of the Korean Geosynthetics Society
• /
• v.16 no.4
• /
• pp.231-240
• /
• 2017

Recently, there have been frequent occurrences of ground sink in the urban area, which have resulted in human and material damage and are accompanied by economic losses. This is caused by artificial factors such as soil loss, poor compaction, horizontal excavation due to the breakage of the aged sewage pipe, and lack of water proof at vertical excavation. The ground sink can be prevented by preliminary restoration and reinforcement through exploration, but it can be considered that it is not suitable for urgent restoration by the existing method. In this study, a model experiment was carried out to simulate the in-ground cavities caused by groundwater flow for developing non-excavation urgent restoration in underground cavity and the range of the relaxation zone was estimated by detecting the around the cavity using a relaxation zone detector. In addition, disturbance region and relaxation region were separated by injecting gypsum into cavity formed in simulated ground. The shape of the underground cavity due to the groundwater flow was similar to that of the failure mode III formed in the dense relative density ground due to water pipe breakage in the previous study. It was confirmed that the relaxed region detected using the relaxation zone detector is formed in an arch shape in the cavity top. The length ratio of the relaxation region to the disturbance region in the upper part of the cavity center is 2: 1, and it can be distinguished by the difference in the decrease of the shear resistance against the external force. In other words, it was confirmed that the secondary damage should not occur in consideration of the expandability of the material used as the injecting material in the pre-repair and reinforcement, and various ground deformation states will be additionally performed through additional experiments.

• Journal of the Korean Arthroscopy Society
• /
• v.8 no.1
• /
• pp.37-44
• /
• 2004

Purpose: To evaluate the optimal number of additional half hitches for achieving an optimal knot-holding capacity (KHC) of Lockable sliding knots. Methods: Four configurations of arthroscopic knots (Duncan loop, Field knot, Giant knot, and SMC knot) were tested for their knot-holding capacity. For each knot configuration, 6 sequential knots were made including the initial sliding knot and additional 5 knots by incrementing one half hitches at a time. Each added half-hitch were in reversing half-hitches with alternate posts (RHAPs) fashion. For each sequential knot configuration, 12 knots were made by No. 2 braided sutures. On the servo-hydraulic material testing system (Instron 8511, MTS, Minneapolis, MN), cyclic loading, load to clinical failure (3-mm displacement), load to ultimate failure, and mode of failure were measured. Results: Most of the initial loop without additional half-hitch showed dynamic failure with cyclic loading. The mean displacement after the end of cyclic loading decreased with each additional half-hitches. SMC and Giant knot reached plateau to 0.1 mm or less displacement after one additional half-hitch, shereas Field and Duncan loop needed 3 additional half-hitches. The SMC and Duncan knots needed 1 additional half-hitch to reach greater than 80N at clinical failure, whefeas the other 2 knots needed2 additional half-hitches. For the load exceeding 100N for clinical failure, the SMC knot required 3 additional half-hitches and the other three knots needed 4 additional half-hitches. As the number of additional half-hitches incremented, the mode of failure switched from pure loop failure (slippage) to material failure (breakage). Duncan loop showed poor loop security in that even with 5 additional half-hitches, some failed by slippage (17%). On the other hand, after 3 additional half-hitches, the 3 other knots showed greater than 75% of failure by material breakage mode (SMC and Field 92%, Giant 75%). Conclusion: Even with its own locking mechanism, lockable sliding knot alone does not withstand the initial dynamic cyclic load. For all tested variables, SMC knot requires a minimum of 2 additional half-hitches. Duncan knot may need more than 3 additional half-hitches for optimal security. All knots showed a mear plateau in knot security with 3 or more additional half-hitches.

• Korean Chemical Engineering Research
• /
• v.55 no.3
• /
• pp.322-331
• /
• 2017

District heating was first introduced in Korea in 1985. As the service life of the underground thermal piping network has increased for more than 30 years, the maintenance of the underground thermal pipe has become an important issue. A variety of complex technologies are required for periodic inspection and operation management for the maintenance of the aged thermal piping network. Especially, it is required to develop a model that can be used for decision making in order to derive optimal maintenance and replacement point from the economic viewpoint in the field. In this study, the analysis was carried out based on the repair history and accident data at the operation of the thermal pipe network of five districts in the Korea District Heating Corporation. A failure probability model was developed by introducing statistical techniques of qualitative analysis and binomial logistic regression analysis. As a result of qualitative analysis of maintenance history and accident data, the most important cause of pipeline damage was construction erosion, corrosion of pipe and bad material accounted for about 82%. In the statistical model analysis, by setting the separation point of the classification to 0.25, the accuracy of the thermal pipe breakage and non-breakage classification improved to 73.5%. In order to establish the failure probability model, the fitness of the model was verified through the Hosmer and Lemeshow test, the independent test of the independent variables, and the Chi-Square test of the model. According to the results of analysis of the risk of thermal pipe network damage, the highest probability of failure was analyzed as the thermal pipeline constructed by the F construction company in the reducer pipe of less than 250mm, which is more than 10 years on the Seoul area motorway in winter. The results of this study can be used to prioritize maintenance, preventive inspection, and replacement of thermal piping systems. In addition, it will be possible to reduce the frequency of thermal pipeline damage and to use it more aggressively to manage thermal piping network by establishing and coping with accident prevention plan in advance such as inspection and maintenance.

• Korean Journal of Poultry Science
• /
• v.21 no.1
• /
• pp.1-19
• /
• 1994

This study was carried out to investigate the effects of shperical surface of eggs tray and eggshell on breaking strength of eggs for the development of a new egg tray design to prevent eggshell breakage. The results obtained were as follows: 1. According to the results obtained from investigation on the types of 22 egg trays collected from 9 countries(USA, Italy, France, Thailand, Japan, Netherland, Russia, Korea and Swiss), all egg trays except those from Korea were different in their types. 2. According to the determination of breaking strength for 4 pilot egg trays, type B and D were high in breaking strength. Trays B and D which would fit with the spherical surface of egg so that they could increase breaking strength were most recommendable. Breaking strength was not increased even though egg tray was strong. Thickness of eggshell of experimental eggs used in this experiment have no significance (P>0.05). 3. When eggs are packed and transported in egg tray, the breaking strength will depend on how much spherical surface of egg are covered by the spherical surface of the egg tray. Therefore, the inner spherical surface of egg tray must fit to the outer spherical surface of eggs when the egg tray is manufactured. 4. At present, there is only one type of egg tray being used in Korea despite the various egg sizes. In order to minimize the eggshell breakage, however, proper sizes or types of egg trays should be developed for each different categories of the egg size.

• Korean Journal of Plant Resources
• /
• v.25 no.5
• /
• pp.568-577
• /
• 2012

The objective of this study was to investigate the antioxidative capacity of ethanol extracts from Rumex crispus L. The concentration of R. crispus L. extract at which DPPH radical scavenging activity was inhibited by 50% was 2.15 mg/mL, which was lower than that of ${\alpha}$-tocopherol (0.43 mg/mL), as compared to 100% by pyrogallol as a reference. Total antioxidant status was examined by total antioxidant capacity against ABTS radical reactions. Total antioxidant capacities of R. crispus L. extract at concentrations of 0.1 and 1 mg/mL were 0.47 and 2.33 mM Trolox equivalents, respectively, which were higher than those of ${\alpha}$-tocopherol. Superoxide scavenging activities of R. crispus L. extract at concentrations of 0.1 and 1 mg/mL were 21.5 and 78.9%, respectively, which were not significantly (p>0.05) different from those of catechin. Oxygen radical absorbance capacities of R. crispus L. extract at concentrations of 20 and 100 ${\mu}g/mL$ were 62.5 and 156.4 ${\mu}M$ Trolox equivalents, respectively, which were lower than those of ascorbic acid. Cupric reducing antioxidant capacities of R. crispus L. extract at concentrations of 0.1 and 1 mg/mL were 0.28 and 1.88 mM Trolox equivalents, which were similar or significantly (p<0.05) higher than those of ${\alpha}$-tocopherol, respectively. R. crispus L. extract prevented supercoiled DNA strand breakage induced by hydroxyl radical and peroxyl radical. Total phenolic contents of R. crispus L. extract at concentrations of 0.5 and 5 mg/mL were 0.58 and 3.85 mM gallic acid equivalents, respectively. R. crispus L. extract at concentration of 0.1 and 0.5 mg/mL inhibited 0.2 mM tert-butyl hydroperoxide-induced cytotoxicity by 38.5 and 63.5%, respectively, in HepG2 cell culture system. Thus, strong antioxidant and cytotoxicity-inhibiting effects of R. crispus L. extract seem to be due to, at least in part, the prevention from free radicals-induced oxidation as well as high levels in total phenolic contents.

• Journal of Yeungnam Medical Science
• /
• v.14 no.1
• /
• pp.209-219
• /
• 1997

Objectives: Anterior approach to achieve arthrodesis of the cervical spine has become a widely accepted and often-used approach since its earliest reports by Bailey and Badgley, Smith and Robinson and Cloward. However, anterior interbody fusion in the presence of the posterior instability may be complicated by the bone graft dislodgement, kyphotic defomity or nonunion. As an attemp to prevent this undesirable complication, additional methods such as skeletal traction, halo appratus or even posterior fusion has been utilized. Therefore, The cervical spine locking plate(CSLP) with the anterior intervertebral body bone grafting provide immediate cervical stabilization and widely successful in achieving fusion. Material and methods: This study analysed 14 patients who underwent a single anterior procedure and application of CSLP for the treatment of the cervical spinal disorder. Eleven patients were disc herniations and three patients were traumatic lesion. The average age of the patient was 47 years and the mean follow up periods was 20 months ranging from 13 to 27 months. Results: Ambulation was started 2nd day after the operation with the aid of the Philadelpia orthoses. Bone union was observed 13 cases on average 12 weeks after operation. The one case was nonunion with plate breakage without clinical symptom. Conclusion: Anterior fusion with CSLP are thought to be a safe and valuable method for treating cervical spine disorder.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.58.1-58.1
• /
• 2010

In solar cell module manufacturing, single solar cells has to be joined electrically to strings. Copper stripes coated with tin-silver-copper alloy are joined on screen printed silver of solar cells which is called busbar. The bus bar collects the electrons generated in solar cell and it is connected to the next cell in the conventional module manufacturing by a metal stringer using conventional hot air or infrared lamp soldering systems. For thin solar cells, both soldering methods have disadvantages, which heats up the whole cell to high temperatures. Because of the different thermal expansion coefficient, mechanical stresses are induced in the solar cell. Recently, the trend of solar cell is toward thinner thickness below 180um and thus the risk of breakage of solar cells is increasing. This has led to the demand for new joining processes with high productivity and reduced error rates. In our project, we have developed a new method to solder solar cells with a laser heating source. The soldering process using diode laser with wavelength of 980nm was examined. The diode laser used has a maximum power of 60W and a scanner system is used to solder dimension of 6" solar cell and the beam travel speed is optimized. For clamping copper stripe to solar cell, zirconia(ZrO)coated iron pin-spring system is used to clamp both joining parts during a scanner system is traveled. The hot plate temperature that solar cell is positioned during lasersoldering process is optimized. Also, conventional solder joints after $180^{\circ}C$ peel tests are compared to the laser soldering methods. Microstructures in welded zone shows that the diffusion zone between solar cell and metal stripes is better formed than inIR soldering method. It is analyzed that the laser solder joints show no damages to the silicon wafer and no cracks beneath the contact. Peel strength between 4N and 5N are measured, with much shorter joining time than IR solder joints and it is shown that the use of laser soldering reduced the degree of bending of solar cell much less than IR soldering.

• Journal of the Microelectronics and Packaging Society
• /
• v.27 no.1
• /
• pp.37-43
• /
• 2020

The effects of O₂ plasma pre-treatment and post-annealing conditions on the interfacial adhesion of Ti thin film and WPR dielectric were investigated using 90° peel test for fan-out wafer level packaging (FOWLP) redistribution layer (RDL) applications. Peel strength between Ti film and WPR dielectric decreased from 8.9±1.3 g/mm to 2.7±0.9 g/mm for variation of O₂ plasma pre-treatment time from 30s to 300s, which is closely related to C-O-C or C=O bonds breakage at the WPR dielectric surface due to excessive plasma pre-treatment conditions. During post-annealing at 150℃, the peel strength abruptly decreased from 0 h to 24 h, and then maintained constant until 100 h, which is also mainly due to the damage of WPR dielectric which is weak to high temperature. Therefore, the optimum plasma pre-treatment conditions on the surface of dielectric is essential to interfacial reliability of FOWLP RDL.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.27 no.2
• /
• pp.75-79
• /
• 2017

Honeycomb-shaped Ag-grid transparent conductive electrodes (TCEs) were fabricated using two different processes, high density plasma etching and lift-off, and the optical and electrical properties were compared according to the fabrication method. For the fabrication of the Ag-grid TCEs by plasma etching, etch characteristics of the Ag thin film in $10CF_4/5Ar$ inductively coupled plasma (ICP) discharges were studied. The Ag etch rate increased as the power increased at relatively low ICP source power or rf chuck power conditions, and then decreased at higher powers due to either decrease in $Ar^+$ ion energy or $Ar^+$ ion-assisted removal of the reactive F radicals. The Ag-grid TCEs fabricated by the $10CF_4/5Ar$ ICP etching process showed better grid pattern transfer efficiency without any distortion or breakage in the grid pattern and higher optical transmittance values of average 83.3 % (pixel size $30{\mu}m/line$ width $5{\mu}m$) and 71 % (pixel size $26{\mu}m/line$ width $8{\mu}m$) in the visible range of spectrum, respectively. On the other hand, the Ag-grid TCEs fabricated by the lift-off process showed lower sheet resistance values of $2.163{\Omega}/{\square}$ (pixel size $26{\mu}m/line$ width $18{\mu}m$) and $4.932{\Omega}/{\square}$ (pixel size $30{\mu}m/line$ width $5{\mu}m$), respectively.