• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.1143-1144
• /
• 2010

• 한국방사선학회논문지
• /
• 제10권6호
• /
• pp.435-442
• /
• 2016

본 연구는 X-선관 각도 변경에 따른 경사효과(Anode Heel Effect)의 변화를 알아보고자 실시하였다. 실험조건은 70 kV, 30 mAs, 초점-검출기간의 거리 100 cm, 조사야는 $35{\times}43cm^2$, 측정점은 조사야의 정중앙점에서 좌우 3.5 cm 간격으로 나누어 양극쪽으로 A1, A2, A3, A4, A5, A6 점을 설정하고 음극쪽으로 C1, C2, C3, C4, C5, C6 점으로 설정하였다. X-선관을 수직으로 하여 측정점인 A6에서 C6까지 각각 입사표면선량을 측정하였다. 다음에 X-선관을 양극쪽으로 15도 30도로 변경 하면서 각각 측정하고 같은 방법으로 음극쪽으로 15도 30도로 변화시켜 측정하였다. 결과로 X-선관이 수직인 경우 A5보다 C5점이 3배정도 입사표면선량이 높게 나타나 수직 촬영 시 방사선감수성이 높은 장기가 위치해 있는 쪽으로 양극을 위치시키면 피폭을 줄일 수 있었다. X-선관의 각도를 주고 촬영할 경우에는 음극측으로 각도를 주는 것이 양극과 음극측의 입사표면선량 차이를 줄일 수 있으며 상, 하 두께 차이가 있는 부위를 촬영할 경우에는 음극측이 두꺼운 부위를 향하게 각도를 주는 것이 입사표면선량의 차이를 줄여 좀 더 균일한 영상을 만들 수 있었다.

• 한국재료학회지
• /
• 제13권3호
• /
• pp.160-168
• /
• 2003

The co-firing processes for the supported type planar solid oxide fuel cell were investigated. A flat cell of $7.7${\times}$10.8\textrm{cm}^2$ was fabricated successfully by the co-firing process, in which green films were co-sintered in the forms of two layers of anode/electrolyte or of three layers of anode/electrolyte/cathode with gas distributor. A co-fired cell of two layers yielded a power of 200 ㎽/$\textrm{cm}^2$ at 608 ㎷. Its performance loss was mainly due to iR drop in the anodic gas distributor, which was attributed to poor contact between anodic gas distributor and current collector. The performance in the co-fired cell of three layers was much lower than that of two layers, which resulted from the large iR drop and activation overvoltage at the cathodic side. In the co-fired cell of two layers, the impedance analysis indicated that the performance decay during cell operation is due to both anode overvoltage and iR drop at anode side. Also the electrode reaction of the co-fired two layers' cell is considered to be controlled by activation overvoltage within the low current of 50 ㎃.

• 한국재료학회지
• /
• 제8권6호
• /
• pp.571-576
• /
• 1998

본 연구에서는 용융탄산염 연료전지용 분리판으로서 오스테나이트계 스테인레스강 중, 310S를 사용하여 용융염 전해질 및 양극측 분위기에서 부식거동, 부식생성물의 형성과정 및 기구에 관한 고찰을 실시하였다. 분리판의 부식 진행과정은 부식반응 이후 안정 부식생성물이 형성되기까지 빠른 부식이 진행되는 부식생성물 형성단계와 안정 부식생성물 형성 후 보호파괴가 일어나기 까지의 부식 억제단계, 그리고 보호파괴 이후 부식이 다시 증가되는 부식 진행단계의 3단계 과정을 경유하며 진행하였다. 분리판 내 원소들의 농도분포는 부식생성물 형성영역에서는 Fe가, 부식 방어영역에서는 Cr이, 그리고 Ni은 Cr 고갈영역과 기지 안쪽에서 높게 형성되었다. 또한 양극측에서 분리판은 전해질의 이온화에 의한 부식이 주된 부식기구였으며, 최종 부식생성물은 $LiFeO_2$와 $LiCrO_2$였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.311-311
• /
• 2009

Carbon nanotubes (CNTs) belong to an ideal material for field emitters because of their superior electrical, mechanical, and chemical properties together with unique geometric features. Several applications of CNTs to field emitters have been demonstrated in electron emission devices such as field emission display (FED), backlight unit (BLU), X-ray source, etc. In this study, we fabricated a CNT cathode by using filtration processes. First, an aqueous CNT solution was prepared by ultrasonically dispersing purified single-walled CNTs (SWCNTs) in deionized water with sodium dodecyl sulfate (SDS). The aqueous CNT solution in a milliliter or even several tens of micro-litters was filtered by an alumina membrane through the vacuum filtration, and an ultra-thin CNT film was formed onto the alumina membrane. Thereafter, the alumina membrane was solvated by acetone, and the floating CNT film was easily transferred to indium-tin-oxide (ITO) glass substrate in an area defined as 1 cm with a film mask. The CNT film was subjected to an activation process with an adhesive roller, erecting the CNTs up to serve as electron emitters. In order to measure their luminance characteristics, an ITO-coated glass substrate having phosphor was employed as an anode plate. Our field emitter array (FEA) was fairly transparent unlike conventional FEAs, which enabled light to emit not only through the anode frontside but also through the cathode backside, where luminace on the cathode backside was higher than that on the anode frontside. Futhermore, we added a reflecting metal layer to cathode or anode side to enhance the luminance of light passing through the other side. In one case, the metal layer was formed onto the bottom face of the cathode substrate and reflected the light back so that light passed only through the anode substrate. In the other case, the reflecting layer coated on the anode substrate made all light go only through the cathode substrate. Among the two cases, the latter showed higher luminance than the former. This study will discuss the morphologies and field emission characteristics of CNT emitters according to the experimental parameters in fabricating the lamps emitting light on the both sides or only on the either side.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2009년도 춘계학술발표대회
• /
• pp.31.1-31.1
• /
• 2009

Carbon nanotubes (CNTs) are attractive material because of their superior electrical, mechanical, and chemical properties. Furthermore, their geometric features such as a large aspect ratio and a small radius of curvature at tip make them ideal for low-voltage field emission devices including backlight units of liquid crystal display, lighting lamps, X-ray source, microwave amplifiers, electron microscopes, etc. In field emission devices for display applications, the phosphor anode is positioned against the CNT emitters. In most case, light generated from the phosphor by electron bombardment passes through the anode front plate to reach observers. However, light is produced in a narrow depth of the surface of the phosphor layer because phosphor particles are big as much as several micrometers, which means that it is necessary to transmit through the phosphor layer. Hence, a drop of light intensity is unavoidable during this process. In this study, we fabricated a transparent cathode back plate by depositing an ultra-thin film of single walled CNTs (SWCNTs) on an indium tin oxide (ITO)-coated glass substrate. Two types of phosphor anode plates were employed to our transparent cathode back plate: One is an ITO glass substrate with a phosphor layer and the other is a Cr-coated glass substrate with phosphor layer. For the former case, light was radiated from both the front and the back sides, where luminance on the back was ~30% higher than that on the front in our experiments. For the other case, however, light was emitted only from the cathode back side as the Cr layer on the anode glass rolled as a reflecting mirror, improving the light luminance as much as ~60% compared with that on the front of one. This study seems to be discussed about the morphologies and field emission characteristics of CNT emitters according to the experimental parameters in fabricating the lamps emitting light on the both sides or only on the cathode back side. The experimental procedures are as follows. First, a CNT aqueous solution was prepared by ultrasonically dispersing purified SWCNTs in deionized water with sodium dodecyl sulfate (SDS). A milliliter or even several tens of micro-liters of CNT solution was deposited onto a porous alumina membrane through vacuum filtration. Thereafter, the alumina membrane was solvated with the 3 M NaOH solution and the floating CNT film was easily transferred to an ITO glass substrate. It is required for CNT film to make standing CNTs up to serve as electron emitter through an adhesive roller activation.

• 한국콘텐츠학회논문지
• /
• 제10권6호
• /
• pp.307-311
• /
• 2010

본 연구는 검출기 측정방법에 따라 관전압 정확도 검사결과인 PAE값이 어떻게 달라지는지 알아보고자 한다. 실험방법으로는 측정거리와 X선관 각도, 방향에 따른 PAE값의 변화실험에서는 초점과 측정기간의 거리를 100cm, 80cm, 60cm에 위치시킨 상태에서 관전압지시치는 70kVp, X선관 각도는 음극, 양극측으로 $5^{\circ},\;10^{\circ},\;15^{\circ},\;20^{\circ},\;25^{\circ},\;30^{\circ}$로 맞추어 측정하고, 관전압지시치에 따른 PAE값의 변화실험에서는 관전압 60kVp, 70kVp, 80kVp, 90kVP, 100kVp를 설정하고 소초점과 대초점을 전환하며 측정하였다. 측정거리와 X선관 각도, 방향에 대한 PAE값의 결과를 보면 100cm일 경우에는 음극측에서 전체적으로 PAE값이 높게 나타났으며 80cm, 60cm일 경우에는 양극측에서 높게 나타났다. PAE값의 변동율은 100cm일 경우 음, 양극측 모두 안정적으로 나타났으며 80cm, 60cm일 경우에는 불균형적으로 나타났다. 관전압지시치에 따른 PAE값의 결과로는 대초점보다는 소초점이 높게 나타났으며, 지시치가 클수록 높게 나타났다. 오차 범위는 지시치가 클수록 적게 나타났다.

• 전기화학회지
• /
• 제10권4호
• /
• pp.301-305
• /
• 2007

연료전지 운전 중에 스택(stack) 분리판 접착부위나 다른 경로로 부동액이 누설될 경우에는 화학적 반응에 영향을 주어 성능의 저하가 발생할 수 있다. 본 연구에서는 부동액이 누설되었을 경우의 성능 거동을 관찰하는 실험을 수행하였다. $400mA/cm^2$ 전류밀도 조건에서 마이크로 펌프를 이용하여 부동액을 주입하였으며 상대습도 100%/100%와 수소와 공기의 양론비는 1.5/2.0으로 고정하여 실험을 수행하였다. 3 cell stack을 이용하여 부동액을 주입한 후 정전류 회복 실험을 수행한 결과 cathode측에 부동액을 주입하였을 경우에는 성능이 회복되었고 anode측에 부동액을 주입하였을 경우에는 성능이 회복되기 어려운 것으로 나타났다. Anode측이 회복되지 못하는 이유로는 ethylene glycol의 산화반응에서 발생하는 불순물에 의한 피독 현상과 GDL과 3상 계면에 ethylene glycol이 물리적으로 흡착하였을 경우 반응에 필요한 연료 공급의 방해로 인한 성능 저하를 예상할 수 있다. 성능 저하에 영향을 주는 두 가지 변수를 확인하는 실험을 수행하였다. 회복 실험은 anode측에 water pump를 이용하여 질소 기체와 물을 동시에 공급하는 방법으로 실험을 수행하였고, 1시간 간격으로 성능 회복 유무를 확인하였다. 성능 평가는 polarization curve, cyclic voltammetry(CV), electrochemical impedance spectroscopy(EIS)를 사용하였으며, 정량분석은 gas chromatography를 이용하여 분석하였다. 부동액 주입 후 성능은 크게 저하되었고 정전류 회복 실험에서도 성능 회복은 미미하게 나타났다. 이 후 물 주입회복 실험을 수행하였고 회복 실험을 수행한 2시간 이후에는 93% 이상의 회복을 관찰할 수 있었다.

• 한국전기전자재료학회논문지
• /
• 제25권3호
• /
• pp.241-246
• /
• 2012

A layered planer SOFC module was designed from planar-type SOFC. It was prepared by multi-layered ceramic technology. To form the cathode and the anode in the layered structure, reliable channels should be made on the both side of electrolyte perpendicularly. However, monolithic SOFC using multi-layered ceramic technology hasn't been studied another group, and the warpage of electrolyte in the channel, also, hasn't been studied, when electrode is printed on the electrolyte. In this study, the channels are prepared with electrode printing, and their warpage are evaluated. In the case of YSZ without electrode, the warpages are nothing in the limit of measurement using optical microscope. The warpage of 'YSZ-NiO printed' increases than that of 'NiO printed', and also, the case of 'double electrode printed' is similar to 'YSZ-NiO printed'. It is thought that, in the printed electrolyte, the warpage is related to the difference of the sintering behavior of each material.

• 마이크로전자및패키징학회지
• /
• 제18권3호
• /
• pp.67-74
• /
• 2011

Keys to high wiring density semiconductor packages include flip-chip bonding and build-up substrate technologies. The current issues are the establishment of a fine pitch flip-chip bonding technology and a low coefficient of thermal expansion (CTE) substrate technology. In particular, electromigration and thermomigration in fine pitch flipchip joints have been recognized as a major reliability issue. In this paper, electromigration and thermomigration in Cu/Sn-3Ag-0.5Cu (SAC305)/Cu flip-chip joints and electromigration in Cu/In/Cu flip chip joints are investigated. In the electromigration test, a large electromigration void nucleation at the cathode, large growth of intermetallic compounds (IMCs) at the anode, a unique solder bump deformation towards the cathode, and the significantly prolonged electromigration lifetime with the underfill were observed in both types of joints. In addition, the effects of crystallographic orientation of Sn on electromigration were observed in the Cu/SAC305/Cu joints. In the thermomigration test, Cu dissolution was accelerated on the hot side, and formation of IMCs was enhanced on the cold side at a thermal gradient of about $60^{\circ}C$/cm, which was lower than previously reported. The rate of Cu atom migration was found comparable to that of electromigration under current conditions.