• Journal of the Korean Society of Costume
• /
• v.45
• /
• pp.17-28
• /
• 1999

This study was to analyze factors of the body form and factors of bodice pattern through a surface developement figure for the tight bodice pattern design. Fifty replicas of the trunk surface were made by applying a surgical tape method of female subjects between 18 and 24 years old. The result was as follows: 1. The gaps between direct measurements and measurements of the surface development figure were regarded as allowances for the tight bodice pattern. 2. There are four factors of body form selected by factor analysis. The 1st factor signifies th degree of fatness in the upper body. The 2nd factor signifies the length of the upper body. The 3rd factor signifies the part of the front shoulder. The 4th factor signifies the part of the neck. 3. There are high correlations between center back line of the surface development figure and back length line side line front length line back neck depth back upper chest depth. There are high correlations between back bust line of the surface development figure and back interscye breadth line back upper chest line back armhole line. There are high correlations between front bust line of the surface development figure and front upper chest line front interscye breadth line front armhole line front neck breadth 4. The regression expressions of measurements of the surface development figure of the upper body were analyzed as(Fig. 3).

• Korean Journal of Agricultural Science
• /
• v.42 no.3
• /
• pp.231-235
• /
• 2015

This study was performed to investigate the change of the body surface temperature during socialization of weaning pigs. A total of 108 piglets (Landrace 60 and Yorkshire 48) aged 31 (${\pm}1.1$) day was used for this study. Experiment was designed as follows; familiar group (T1), randomly mixed with unfamiliar piglets (T2), mixed based on weight of unfamiliar piglet (T3). The transport and mixing of pigs were performed at 10:00, and then body surface temperature was taken by thermo-graphic camera after 4 hours (14:00). Average surface temperature and hot-spot-temperature, which is the hottest spot of the body surface, were analyzed using Testo IRsoft 3.1 software. Average temperature of body surface were 36.0, 38.2, and 37.5 in T1, T2, and T3, respectively. Average of body surface temperature in T2 and T3 were higher (p<0.001) than T1, and average temperature of body surface of T3 was greater (p<0.001) than that of T2. The hot-spot-temperature of T1, T2, and T3 were 38.7, 39.5, and 39.6, respectively. The hot-spot-temperature of T2 (p<0.01) and T3 (p<0.001) were significantly higher than that of T1. Above results demonstrate that grouping unfamiliar pigs leads to increase in the body temperature possibly by pigs aggressive behavior during social conflict. By the result on average body temperature, this study suggests that the mixing with similar body weight would increase the struggle time and frequency.

• Journal of Fashion Business
• /
• v.17 no.1
• /
• pp.170-185
• /
• 2013

The suitability of the pattern manufactured with the development figure was considered by reviewing the development conditions that can be directly connected to the basic pattern in the human body surface development figure with the cast bandage method. The method to prepare the sleeve basic pattern was based on the cylindrical surface development method, and the sleeve basic pattern covering the 45 and 90 degrees momentum of the arm-movement was made by using the cast-type body surface development figure prepared with the horizontal line of the sleeve hem placed horizontally in the plan and by combining the cast-type body surface development figure in the standing position with the figure in the moving position. The test clothing was prepared with the sleeve pattern adding the bodice pattern in the standing position and the momentum and was worn on the FRP replica. The relationship theory of the body surface development figure with the pattern was derived by reviewing the suitability from the wearing state. The sleeve-cap height of the sleeve basic pattern resulted in about 80% in the standing position when the needs for a physical activity are 45 degrees and the about 50% when the needs for a physical activity are 90 degrees. The additional size of the diagonal length of the sleeve-cap could be set as "0" if the sleeve-cap height is low by 50% and as 50% of the additional size in the standing position if the sleeve-cap height is 80%.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.33 no.7
• /
• pp.1109-1120
• /
• 2009

This study develops a fitted torso type basic pattern for men by utilizing 3D body scan data. Recent fashion trends are reflected in the development of the pattern. The subjects were 15 men in their 20's, who wear size 95 (M size). Body scan data was obtained through a 3D whole body scanner (WB4, Cyberware, USA), and a body surface development figure for developing male fitted torso type basic pattern was attained through the use of Rapid Form 2006 as well as Auto CAD 2006 programs. The results are as follows: A body surface development figure through body surface segment method showed high exactitude in an error range of 100$\pm$1%. In addition, it occurred in an error range of 100:1:3% because of the hard scanning conditions in the incline of the shoulder and armpit areas. However, the body surface development figure as well as the direct measurement results can be used as basic data for the given patternmaking since the error range falls into 100$\pm$3%. Dart amounts obtained from the average cross section were center back 2.2cm (24.3%), back armpit point 3.8cm (41.8%), front armpit point 3.0cm (33.9%). As shown the jacket pattern, the biggest dart amount was portioned out at the back armpit point. The drafting equations for the development pattern acquired are as follows; Full width=C/2+5cm, back length=height/4-1cm, armhole depth=(C/10+12cm)+3cm, back width=2C/10+2cm, front width=2C/10. The development pattern was a fitted torso basic pattern that was composed of 3 pieces, so it would be very useful in developing shirt or jacket patterns. According to the results of the evaluation of the developed pattern appearance, it obtained higher scores of over 3.5 points in almost items, meaning that the developed pattern is appropriate for a male fitted torso type basic pattern. It suggests a possibility of patternmaking from a body surface development figure in 2-D to prototype.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.20 no.5
• /
• pp.852-859
• /
• 1996

The factors and mechanism of arm surface changes were analyzed by regression analysis for the relationship between changes in arm joint angle and arm surface changes, according to the direction of upper extremity motion. Body surface change patterns among subjects were tested also. Experiments were carried out on 3 female subjects of different body types to examine 26 motions in 4 directions for 4 upper extremity parts. The major conclusions of the study are as follows: 1. The expansion or contraction of arm surface length depends on the direction of upper extremity motion. 2. Arm surface length changes by linear expansion or contraction according to the joint angle of the direction of motion. The mechanism of arm surface changes is represented by a linear relation between arm surface changes and the (actors of the direction of upper extremity motion and arm joint angle. 3. Arm surface length shows the same pattern of body surface changes regardless of body type. A quantitative model of body surface changes at upper extremity should be developed for functional sleeve design.

• The Bulletin of The Korean Astronomical Society
• /
• v.46 no.2
• /
• pp.76.3-77
• /
• 2021

GMT secondary mirror system consists of 7 segmented adaptive mirrors. Each segment consists of a thin shell mirror, actuators and a reference body. The thin shell has a few millimeters of thickness so that it can be easily bent by push and pull force of actuators to compensate the wavefront disturbance of light due to air turbulence. The one end of actuator is supported by the reference body and the other end is adapted to this thin shell. One of critical role of the reference body is to provide the reference surface for the thin shell actuators. Therefore, the reference body is one of key components to succeed in development of GMT ASM. Recently, Korea Research Institute of Standards and Science (KRISS) and University of Arizona (UA) has signed a contract that they will cooperate to develop the first set of off-axis reference body for GMT ASM. This project started August 2021 and will be finished in Dec. 2022. The reference body has total 675 holes to accommodate actuators and 144 pockets for lightweighting. The rear surface has a curved rib shape with radius of curvature of 4387 mm with offset of 128.32mm. Since this reference body is placed just above the thin shell so that the front surface shape needs to be close to that of thin shell. The front surface has a concave off-axis asphere, of which radius of curvature is 4165.99 mm and off-axis distance is about 1088 mm. The material is Zerodur CTE class 1 (CTE=0.05 ppm/oC) from SCHOTT. All the actuator holes and pockets are machined normal to the front surface. It is a very complex challenging optical elements that involves sophisticated machining process as well as accurate metrology. After finishing the fabrication of reference body in KRISS, it will be shipped to UA for final touches and finally sent to Adoptica in Italy, in early 2023. This paper presets the development plan for the GMT ASM Reference Body and relevant fabrication and metrology plans.

• The Research Journal of the Costume Culture
• /
• v.14 no.3 s.62
• /
• pp.434-442
• /
• 2006

The purpose of this study was to develop the beautiful basic bodice pattern that satisfied both functionality and aesthetics on the basis of the change in the figure and length of surface body for each movement through a three-dimensional development figure of surface body for young women (aged between 18 and 24) who were very sensitive to fitness of clothes. Existing three basic bodice patterns (Yim wonja-, ESMOD-, and FIT-types) were selected and then compared and analyzed in terms of drawing methods and the wearing test was carried out by a sensory test in order to design an experimental prototype. The design of study prototype was improved by three wearing test that was correlated with low satisfactory item. And the ease was established by difference of previous direct measurement and body surface measurement.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.04a
• /
• pp.701-708
• /
• 1997

A direct boundary element method(DBEM) is developed for thin bodies whose surfaces are rigid or compliant. Th eHelmholtz integral equation and its normal derivative integral equation are adopted simultaneously to calculate the pressure on both sides of the thin body, instead of the jump values across it, to account for the different surface conditions of each side. Unlike the usual assumption, the normal velocity is assumed to be discontinuous across the thin body. In this approach, only the neutral surface of the thin body has to be discontinuous across the thin body. In this approach, only the neural surface of the thin body has to be discretized. The method is validated by comparison with analytic and/or numerical results for acoustic scattering and radiation from several surface conditions of the thin body; the surfaces are rigid when stationary or vibrating, and part of the interior surface is lined with a sound-absorbing material.

• The Research Journal of the Costume Culture
• /
• v.28 no.1
• /
• pp.1-14
• /
• 2020

This study is based on a representative body shape drawn from previous studies that classify adult male torso shapes. In this study, a design method is proposed by developing a tight-fit pattern that can be easily developed into various items and designs using the body surface development figure. This is obtained by converting the 3D body shape of the model representing the representative body shape. The specific design method was conducted as follows. Actual measurement values were used for waist back length, waist-to-hip length, shoulder length. The scye depth was determined as C/4-1.7 cm, and the front and back Interscye was set at (1/2 × actual measurements)-0.2 cm. The front-back neck breadth was set to (1/5 × base neck circumference)-1.3 cm and (1/5 × base neck circumference) cm. The front-back neck depth was set to (1/5 × base neck circumference)-1.2 cm and 3.5 cm. Front chest circumference was C/4-1 (front-back difference)cm; (1/4 × back chest circumference) was C/4 + 1 (front-back difference) + 0.3 (dart amount) cm. Front waist circumference was W/4-0.2 (front-back difference) + 2.2 (dart amount) cm; back waist circumference was W/4 + 0.2 (front-back difference) + 2.5 (dartamount) cm; front hip circumference was H/4 + 0.2 (ease) + 0.2 (front-back difference) cm; and back hip circumference was H/4 + 0.2 (ease)-0.2 (front-back difference) cm; Front droop was 1.6 cm. The newly developed tight-fit pattern is expected to be of great use as a basis for garment construction.

• Korean Journal of Human Ecology
• /
• v.18 no.2
• /
• pp.397-406
• /
• 2009

A Study on the Development of Brassiere Pattern for Elderly Women The purpose of this study is to develop functional and sensible brassiere for elderly women. For this purpose, 6 elderly women(aged between 65 and 69) were sampled to be measured for their body sizes and tested for their bressiere wearing. he results were as follows; 1. In order to develop the basic patterns of elderly women's bressieres, 90B size was selected and then, their bressiere fitting was tested. The foundation pattern of the size 90A was proved for the body by the wearing tests. Each angle and length of the parts on the basic line of the breasts played an important role on setting the pattern. 2. As based on the body surface shell extracted from a plastic mold(photo.2), the cup of brassiere pattern were applied to the body surface shell(photo.4), and full side stretch-wings were applied to 13% reduced body size. The design pattern of elderly women's brassiers were characterized by a round wired as well as a full cup(3piece) embracing the entire breasts. 3. As the result of the wearing test, the excellence of the experimental brassiere was recognized objectively, with high marks in all the items(fig. 6). The experimental brassiere was covering the whole breasts to cope with change according to breasts loosing. It was designed to support the breasts firmly.