• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.59-59
• /
• 2011

We will report atomically sharp epitaxial growth of $Bi_2Se_3$ three-dimensional topological insulator films on Si(111) substrate with molecular beam epitaxy (MBE). It was achieved by employing two step growth temperatures to prevent any formation of second phase, like as $SiSe_2$ clusters, between $Bi_2Se_3$ and Si substrate at the early stage of growth. The growth rate was determined completely by Bi flux and the Bi:Se flux ratio was kept ~1:15. The second-phase-free atomically sharp interface was verified by RHEED, TEM and XRD. Based on the RHEED analysis, the lattice constant of $Bi_2Se_3$ relaxed to its bulk value during the first quintuple layer implying the absence of strain from the substrate. Single-crystalline XRD peaks of $Bi_2Se_3$ were observed in films as thin as 4 QL. TEM shows full epitaxial structure of $Bi_2Se_3$ film down to the first quintuple layer without any second phases. This growth method was used to grow high quality epitaxial $Bi_2Se_3$ films from 3 QL to 3600 QL. The magneto-transport properties of these thin films show a robust 2D surface state which is thickness independent.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• v.2 no.2
• /
• pp.97-109
• /
• 1998

A comparison of the two dimensional heat loss, computed using the analytical method and the finite difference method in two models(i.e. one is a parabolic fin whose parabolic curves meet at the fin center line and the other is a transformed parabolic fin whose tip cuts vertically), is made assuming the analytical method is correct. For these methods, the root temperature and surrounding convection coefficients of these fins are assumed as constants. The results show that the relative errors of the heat loss between the two methods for the parabolic fin whose tip cuts vertically are smaller than those for the one whose tip does not cut. In case of Bi=0.01, the values of the heat loss obtained using a finite difference method are close to those values obtained using the analytical method for both models. The values of the heat loss from both models calculated by using the analytical method are almost the same for given range of non-dimensional fin length in case of Bi = 0.01 and 0.1.

• Smart Structures and Systems
• /
• v.13 no.1
• /
• pp.111-135
• /
• 2014

Based on the Reissner mixed variational theorem (RMVT), finite rectangular layer methods (FRLMs) are developed for the three-dimensional (3D) linear buckling analysis of simply-supported, fiber-reinforced composite material (FRCM) and functionally graded material (FGM) sandwich plates subjected to bi-axial compressive loads. In this work, the material properties of the FGM layers are assumed to obey the power-law distributions of the volume fractions of the constituents through the thickness, and the plate is divided into a number of finite rectangular layers, in which the trigonometric functions and Lagrange polynomials are used to interpolate the in- and out-of-plane variations of the field variables of each individual layer, respectively, and an h-refinement process is adopted to yield the convergent solutions. The accuracy and convergence of the RMVT-based FRLMs with various orders used for expansions of each field variables through the thickness are assessed by comparing their solutions with the exact 3D and accurate two-dimensional ones available in the literature.

• Archives of design research
• /
• v.16 no.1
• /
• pp.35-44
• /
• 2003

In the past era, acquisition and utilization of useful information was the main origin of competition. Nowadays, unlike that era, is the era of knowledge information(management) in which we should create a new knowledge on the basis of information and apply it to the field of practice. And more acquisition of information is no more the competitive power of any person, any company and any nation because in such the era of knowledge management, anyone can access and get the information he needs, utilizing internet-based searching system. Such demands of the times of knowledge management change rapidly in each field through knowledge management system and researches about knowledge management are actively processed in various academic branches. However, in our field of design, researches about those demands(knowledge management) still remain on the level of one-dimensional searching service for general data about design. Therefore, in this study, we developed building database of researches on form, color, aesthetical elements, preference image word, satisfaction etc. about CI/BI of home electronics goods, living goods, apparels, and food goods companies, also suggesting searching system through which you can obtain useful data and information helpful for designers to process CI/BI works of new product by using that database. Especially, in case of developing specific CI/BI, various search results through help of suggested system will supply a useful design concept. And more, cross table which is the result of analysis two-dimensional categorical data about existing design factors(such as form, color, aesthetical elements, preference image word, and satisfaction) will make contribution for designers to create a new design knowledge.

• The KSFM Journal of Fluid Machinery
• /
• v.8 no.4 s.31
• /
• pp.14-19
• /
• 2005

Average Bi-directional flow tube was suggested to measure single and two phase flow rate. Its working principle is similar with Pilot tube, however, it makes it possible to eliminate the cooling system which is normally needed to prevent from flashing in the pressure impulse line of Pilot tube when it is used in the depressurization condition. 3-dimensional steady state flow analyses using FLUENT 5.4 code were performed to validate the application of the average bi-directional flow tube in case of water and air flow. In this study, sensitivity studies have been performed to optimize the design features of the average bi-directional flow tube which can be applied for the various experimental conditions. For Re numbers above 1000, the k values are nearly constant regardless of the Re numbers and flow types and calculation results and experimental data coincides quite well. The current FLUENT calculation results suggest that linearity of the k values in various design features of the average BDFT is highly promising, which means that it is quite reasonable to select the typical design of the average BDFT for the convenience of the experimental conditions.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.12
• /
• pp.1455-1461
• /
• 2008

We implemented a subminiature internal antenna that is around 1 cc volume for the mobile phone. The fundamental type of studied antenna is IFA(Inverted F Antenna), and this antenna is designed to be improved efficiency and gain due to minimum current cancellation by the avoidance of multiple bending pattern. For the implementation of multiple band, helix is applied to compensate for short antenna length for low frequency band, and a 3 dimensional pattern is used for high frequency band. We made two kinds of 3D structure antenna. One is a 1 cc volume antenna for GSM/DCS band on the bare board set, and the other is a 1.5 cc volume for the GSM/USPCS mobile phone set. Measurements showed good gain performance that average gain of two antenna on each band are $-3.46{\sim}-0.45\;dBi$ and $-4.80{\sim}-3.29\;dBi$ respectively.

• Journal of IKEEE
• /
• v.21 no.1
• /
• pp.39-45
• /
• 2017

Image compression is now essential for applications such as transmission and storage in data bases. For video and digital image applications the use of long tap filters, while not providing any significant coding gain, may increase the hardware complexity. We use a wavelet transform in order to obtain a set of bi-orthogonal sub-classes of images; First, the design of short kernel symmetric analysis is presented in 1-dimensional case. Second, the original image is decomposed at different scales using a subband filter banks. Third, this paper is presented a technique for obtaining 2-dimensional bi-orthogonal filters using McClellan transform. It is shown that suggested wavelet bases is well used on wavelet transform for image compression. From performance comparison of bi-orthogonal filter, we actually use filters close to ortho-normal filters on application of wavelet bases to image analysis.

• Korean Chemical Engineering Research
• /
• v.56 no.6
• /
• pp.826-831
• /
• 2018

This study presents fabrication of bi-compartmental particles labeled by multiple fluorescence. To compartmentalize fluorescent expression at the particle, two fluorescent dyes with less overlap of the excitation and emission spectra are selected. To ensure the fluorescence stability, the fluorescent dyes contain acrylate functional groups in the molecules so that they can be cross-linked together with monomers constituting the particle. Strong fluorescent expression and compartmentalization were observed at the particle fabricated using the selected fluorescent dyes through confocal microscopy. Furthermore, long-term fluorescence stability was verified by measuring fluorescent expression and intensity for 4 weeks. We anticipate that the bi-compartmental particles labeled by multiple fluorescence can be widely used for multi-target drug delivery system, analysis of 3 dimensional Brownian motion, and investigation of 3 dimensional complex self-assembled morphologies.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.04b
• /
• pp.23-23
• /
• 2009

It has been challenging to increase the thermoelectric figure of merit ($ZT=S^2{\sigma}T/\kappa$) of materials, which determine the efficiency of thermoelectric devices, because the three parameters Seebeck coefficient (S), electrical conductivity ($\sigma$), and thermal conductivity ($\kappa$) of bulk materials are inter-dependent. With the development of nanotechnology, ZT values of nanostructured materials are predicted to be enhanced by classical size effects and quantum confinement effects. In particular, Bi nanowires were suggested as one of ideal thermoelectric materials due to the expected quantum confinement effects for the simultaneous increase in Sand. In this work, we have investigated the thermal conductivity of individual single crystalline Bi nanowires with d = 98 nm and d = 327 nm in the temperature range 40 - 300 K using MEMS devices. The for the Bi nanowire with d = 98 nm was observed to be ~ 1.6 W/m-K at 300 K, which is much lower than that of Bi bulk (8 W/m-K at 300 K). This indicates that the thermal conductivity of the Bi suppressed due to enhanced surface boundary scattering in one-dimensional structures. Our results suggest that Bi nanowires grown by stress-induced method can be used for high-efficiency thermoelectric devices.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2010.06a
• /
• pp.79-79
• /
• 2010

Semimetallic bismuth (Bi) has been extensively investigated over the last decade since it exhibits very intriguing transport properties due to their highly anisotropic Fermi surface, low carrier concentration, long carrier mean free path l, and small effective carrier mass $m^*$. In particular, the great interest in Bi nanowires lies in the development of nanowire fabrication methods and the opportunity for exploring novel low-dimensional phenomena as well as practical application such as thermoelectricity[1]. In this work, we introduce a self-assembled interconnection of nanostructures produced by an on-film formation of nanowires (OFF-ON) method in order to form a highly ohmic Bi nanobridge. A Bi thin film was first deposited on a thermally oxidized Si (100) substrate at a rate of $40\;{\AA}/s$ by radio frequency (RF) sputtering at 300 K. The sputter system was kept in an ultra high vacuum (UHV) of $10^{-6}$ Torr before deposition, and sputtering was performed under an Ar gas pressure of 2m Torr for 180s. For the lateral growth of Bi nanowires, we sputtered a thin Cr (or $SiO_2$) layer on top of the Bi film. The Bi thin films were subsequently put into a custom-made vacuum furnace for thermal annealing to grow Bi nanowires by the OFF-ON method. After thermal annealing, the Bi nanowires cannot be pushed out from the topside of the Bi films due to the Cr (or $SiO_2$) layer. Instead, Bi nanowires grow laterally as a mean s of releasing the compressive stress. We fabricated a self-assembled Bi nanobridge (d=192 nm) device in-situ using OFF-ON through annealing at $250^{\circ}C$ for 10hours. From I-V measurements taken on the Bi nanobridge device, contacts to the nanobridge were found highly ohmic. The quality of the Bi nanobridge was also proved by the high MR of 123% obtained from transverse MR measurements. These results manifest the possibility of self-assembled nanowire interconnection between various nanostructures for a variety of applications and provide a simple device fabrication method to investigate transport properties on nanowires without complex patterning and etching processes.