• Progress in Superconductivity
• /
• 제13권3호
• /
• pp.195-202
• /
• 2012

In this paper, we designed Active Magnetic Bearing (AMB) for large scale Superconductor Flywheel Energy Storage System (SFESS) and PD controller for AMB. And we experimentally evaluated SFESS including hybrid type AMB. The radial AMB was designed to provide force slew rate that was sufficient for the unbalance disturbances at the maximum operating speed. The thrust AMB is a hybrid type where a permanent magnet carries the weight of the flywheel and an electromagnetic actuator generates the dynamic control force. We evaluated the design performance of the manufactured AMB through comparison of FEM analysis and the results of experimental force measurement. In order to obtain gains of PD controller and design a notch filter, the system identification was performed through measuring frequency response including dynamics for the AMBs, a power amp and a sensor using a sine swept test method after levitating the flywheel. Through measuring the current input of the AMBs and the orbit of a flywheel according to rotational speed, we verified excellent control performance of the AMBs with small amount current for the large scale SFESS.

• 한국군사과학기술학회지
• /
• 제5권2호
• /
• pp.169-184
• /
• 2002

In order to extract bearing information from the directional sensors of DIFAR(directional frequency analysis and recording) that is a kind of passive sonobuoy, the cardioid beamforming algorithm applicable to DIFAR system was studied in the frequency domain. the algorithm uses narrow-band signals propagated though the media from the acoustic sources such as ship machineries. The proposed algorithm is expected to give signal to noise ratio of 6dB when it uses the maximum response axis(MRA) among the Cardioid beams. The estimated bearings agree very well with those from GPS data. Assuming the bearings from GPS data to be real values, the estimation errors are analyzed statistically. The histogram of estimation errors in each frequency have Gaussian shape, the mean and standard deviation dropping in the ranges -1.1~$6.7^{\circ}$ and 13.3~$43.6^{\circ}$, respectively. Estimation errors are caused by SMR degradation due to propagation loss between the source and receiver, daily fluctuating geo-magnetic fields, and non-stationary background noises. If multiple DIFAR systems are employed, in addition to bearing, range information could be estimated and finally localization or tracking of a target is possible.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 1995년도 춘계학술발표회 논문집
• /
• pp.117-133
• /
• 1995

• 한국정밀공학회지
• /
• 제21권4호
• /
• pp.72-78
• /
• 2004

In this paper, a development of an inductive position sensor is described. The sensor is similar to a radial magnetic bearing in that the sensor stator is shaped like a heteropolar magnetic bearing and is driven by a switching amplifier. A demodulation filter extracts the gap information from the switching current ripples. A prototype sensor exhibits the resolution of $0.43\mum$ and the dynamic bandwidth of about 800Hz. The dynamic performance can be improved by increasing the switching frequency. However, the eddy current effects become noticeable at high switching frequency, thus limiting the improvement of the bandwidth.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.1102-1107
• /
• 2000

The signals that can be obtained from a rotating machine often convey the information of machine. For example, if the machine under investigation has faults, then we can measure the signal which has a pulse train, embedded in noise. Therefore the ability to detect the fault signal in noise determines the degree of diagnosis level of rotating machine. In this paper, minimum variance cepstrum (MV cepstrum), which can easily detect impulse in noise, has been applied to detect the type of faults of ball bearing system. To test the performance of this technique, experiment has been performed for ball bearing elements that have man made faults. Results show that minimum variance cepstrum can easily detect the periodicity due to faults.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 추계학술대회논문집
• /
• pp.1076-1082
• /
• 2003

As functional requirement of massive digital information storage devices are on a trend for the higher data transfer rate and lower cost, many different technical efforts are being tested and implemented in the industry. FDB(Fluid Dynamic Soaring) is one of the major breakthroughs in rotor design in terms of TMR budget. Although FDB analysis based on Reynolds' equation is well established and popularly being used for DB design especially for the estimation of bearing stiffness, there are obvious limitations in the approach due to the inherent assumptions. A generalized analysis tool employing the full Navier-Stokes equation and the energy balance is to be beneficial for detailed FDB design In this publication, an efficient geometry modeling method is presented that provides fully integrated inputs for general FVM/FDM codes. By virtue of the flexibility of the presented method, many different detailed FDB design and analysis are carried over with ease.

• 한국정밀공학회지
• /
• 제32권2호
• /
• pp.135-140
• /
• 2015

It is an important thing for a designer to simulate and predict the performance of a spindle and a rotary table. In addition to the general performance such as static stiffness, the error motion performance information is beneficial to the designer in many cases. However for an aerostatic bearing the fluid film physical status should be calculated in order to simulate those performances and the calculation time is another obstacle for a simple performance simulation. In this paper the investigation on experiment and simulation is performed in order to find a more effective simulation method for the rotational error motion.

• Tribology and Lubricants
• /
• 제23권5호
• /
• pp.195-200
• /
• 2007

This paper presents the friction induced scuffing and wear defects analysis of a pin bushing bearing based on the chemical composition using a scanning microscopy (SEM) and an energy dispersive X-ray analyzer (EDX). The SEM/EDX system, which may provide good information on the surface thermal defects and chemical compositions, provides impurities such as an aluminum, a silicon, a ferrous component and an oxygen, especially. The EDX measured results show that the oxygen may reduce the strength and a hardness of a pin busing, which may lead to a scuffing and a seizure on the rubbing contact surface. The current technology fabricated by a sintering for a pin bushing bearing should be modified or changed to reduce the oxygen composition and the impurities in pin bushing materials.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 하계종합학술대회 논문집(5)
• /
• pp.119-122
• /
• 2001

This paper deals with new type of active magnetic bearing (AMB) for the linear motors. We adopted optical sensing mechanism for the gap sensing. Using the laser and the PSD (Position Sensitive Device), the absolute rotor position is obtained independent of the profile of the guide rail. With this measurement, the rotor can be controller to follow the straight beam of the laser. Another advantage of optical sensing mechanism might be the elimination of the possible interference between the proximity sensor and the electro-magnet. By adopting the push-full actuating mechanism, the bearing stiffness is increased near the equilibrium position. For the simplicity, distributed control system is constructed. Eight independent PID control algorithm is used with the full order observer. Several simulation md test results are presented.

• 한국지반신소재학회논문집
• /
• 제18권3호
• /
• pp.45-53
• /
• 2019

본 연구에서는 건축기초에 적용된 매입 PHC말뚝의 설계사례를 분석하였다. 전반적인 말뚝길이는 최대 35m 이내에서 다양하나, 지지층 조건에 따른 평균 길이는 17.0~18.9m로 큰 차이가 없었다. 지지층 소켓길이는 전체의 약 58%가 시방기준 최소길이인 1m에 따라 설계되었고, 최대 5m까지 설계되었다. 설계효율은 그 편차가 매우 크나 평균 약 70%로서 통상 알려진 범위와 일치하였다. 설계효율이 낮은 용도는 주로 설계하중이 적은 저층건물이나 놀이기구 기초 등으로 나타났다. 풍화암 지지층에서 설계하중은 설계를 지배하는 지반 허용지지력의 65~97%, 허용지지력에 대한 말뚝 허용축하중의 비는 36~115%로 광범위하게 분포하므로 설계효율과 함께 최적화 노력이 요구된다. 반면, 연 경암 지지층의 허용지지력은 대부분 말뚝 허용축하중의 90% 내외로 매우 균등했다. 설계 허용지지력은 선단지지력이 평균 75% 이상을 차지하였으나, 현장재하시험 연구결과를 보면 초기항타 조건에서는 선단지지력이 지배적이며, 재항타 조건에서는 선단지지력이 최소 25%에 불과한 경우도 있었다. 따라서, 설계시 산정된 허용지지력은 시공 초기조건만을 반영하는 것이며, 시간이 경과할수록 말뚝 주면부로의 하중전이가 증가하고, 일부는 시험시 타격에너지 부족으로 선단지지력의 확인이 이루어지지 못한다고 볼 수 있다. 균질한 지반으로 가정했을 때 근입비가 증가할수록 허용축하중이 감소하는 경향이 있었고, 이와 유사하게 지반의 허용지지력도 감소하는 경향을 보여, 큰 설계하중으로 초고강도 말뚝을 적용할 경우 지반의 지지력을 최대한 활용할 수 있음을 알 수 있었다.