• Journal of Information Management
• /
• v.39 no.4
• /
• pp.67-96
• /
• 2008

The open access repository means the knowledge information repository for the producer and the user to share in order for all users of the world to freely access the information free of charge with no legal, economic and technological barrier. This study analyzes and compares the functions offered by each repository by classifying the repository into the organizational repository (dCollection, DSpace@MIT) and the thematic repository (arXiv, PubMed Central) and evaluates the user-centered usability based on the analyzed data. This study at the current times, so called as the Web 2.0 era in which the free access and sharing of the information is important, can be said to have the meaning that the result from the usability evaluation on the open access repository will be used as the fundamental data for developing the future repository.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.5
• /
• pp.37-43
• /
• 2008

The durability test of turbo-blower for PEM fuel cell is very important process of BOP development. It is a major barrier to the commercialization of these systems for stationary and transportation power applications. Commercial viability depends on improving the durability of the air supply system to increase the reliability and to reduce the lifetime cost. In this study, turbo-blower supported by oil-free bearing is introduced as the air supply system used by 80kW proton exchange membrane fuel systems. The turbo-blower is a turbo machine which operates at high speed, so air foil bearings suit their purpose as bearing elements. The impeller of blower was adopted mixed type of centrifugal and axial. So, it has several advantages for variable operating condition. The turbo-blower test results show maximum parasitic power levels below 1.67kW with the 30,000 rpm rotating speed, the flow rate of air has maximum 163SCFM(@PR1.1). For proper application of FCV, these have to durability test. This paper describes the experiment for confirming endurance and stability of the turbo-blower for 500 hours.

• Journal of the Microelectronics and Packaging Society
• /
• v.13 no.4
• /
• pp.45-50
• /
• 2006

Copper via filling is the important factor in 3-D stacking interconnection of SiP (system in package). As the packaging density is getting higher, the size of via is getting smaller. When DC electroplating is applied, a defect-free hole cannot be obtained in a small size via hole. To prevent the defects in holes, pulse and pulse reverse current was applied in copper via filling. The holes, $20\and\;50{\mu}m$ in diameter and $100{\sim}190\;{\mu}m$ in height. The holes were prepared by DRIE method. Ta was sputtered for copper diffusion barrier followed by copper seed layer IMP sputtering. Via specimen were filled by DC, pulse and pulse-reverse current electroplating methods. The effects of additives and current types on copper deposits were investigated. Vertical and horizontal cross section of via were observed by SEM to find the defects in via. When pulse-reverse electroplating method was used, defect free via were successfully obtained.

• Macromolecular Research
• /
• v.12 no.4
• /
• pp.413-421
• /
• 2004

Sulfonated poly(phthalazinone ether sulfone ketone) (SPPESK) membranes and sol-gel derived SPPESK/silica hybrid membranes have been investigated as potential polymer electrolyte membranes for direct methanol fuel cell (DMFC) applications. In comparison with the SPPESK membrane, the SPPESK/silica membranes exhibited higher water content, improved proton conductivity, and lower methanol permeability. Notably, the silica embedded in the membrane acted as a material for reducing the fraction of free water and as a barrier for methanol transport through the membrane. From the results of proton conductivity and methanol permeability studies, we suggest that the fractions of bound and free water should be optimized to obtain desirable proton conductivities and methanol permeabilities. The highly sulfonated PPESK hybrid membrane (HSP-Si) displayed higher proton conductivity (3.42 ${\times}$ 10$^2$ S/cm) and lower methanol permeability (4.15 ${\times}$ 10$\^$7/ $\textrm{cm}^2$/s) than those of Nafion 117 (2.54 ${\times}$ 10$^2$ S/cm; 2.36 ${\times}$ 10$\^$6/ $\textrm{cm}^2$/s, respectively) at 30$^{\circ}C$. This characteristic of the SPPESK/silica membranes is desirable for future applications related to DMFCs.

• Korean Journal of Materials Research
• /
• v.23 no.10
• /
• pp.550-554
• /
• 2013

As continued scaling becomes increasingly difficult, 3D integration has emerged as a viable solution to achieve higher bandwidths and good power efficiency. 3D integration can be defined as a technology involving the stacking of multiple processed wafers containing integrated circuits on top of each other with vertical interconnects between the wafers. This type of 3D structure can improve performance levels, enable the integration of devices with incompatible process flows, and reduce form factors. Through silicon vias (TSVs), which directly connect stacked structures die-to-die, are an enabling technology for future 3D integrated systems. TSVs filled with copper using an electro-plating method are investigated in this study. DC and pulses are used as a current source for the electro-plating process as a means of via filling. A TiN barrier and Ru seed layers are deposited by plasma-enhanced atomic layer deposition (PEALD) with thicknesses of 10 and 30 nm, respectively. All samples electroplated by the DC current showed defects, even with additives. However, the samples electroplated by the pulse current showed defect-free super-filled via structures. The optimized condition for defect-free bottom-up super-filling was established by adjusting the additive concentrations in the basic plating solution of copper sulfate. The optimized concentrations of JGB and SPS were found to be 10 and 20 ppm, respectively.

• Journal of the Korean Magnetics Society
• /
• v.16 no.3
• /
• pp.186-191
• /
• 2006

Ferromagnetic amorphous $Ni_{16}Fe_{62}Si_8B_{14}$ and $Co_{70.5}Fe_{4.5}Si_{15}B_{10}$ layers have been devised and incorporated as free layers of magnetic tunnel junctions (MTJs) to improve MRAM reading and writing performance. The NiFeSiB and CoFeSiB single-layer film exhibited a lower saturation magnetization ($Ms=800emu/cm^3,\;and\;560emu/cm^3$, respectively) compared to that of a $Co_{90}Fe_{10}(Ms=1400emu/cm^3)$. Because amorphous ferromagnetic materials have lower Ms than crystalline ones, the MTJs incorporating amorphous ferromagnetic materials offer lower switching field ($H_{sw}$) values than that of the traditional CoFe-based MTJ. The double-barrier MTJ with an amorphous NiFeSiB free layer offered smooth surface resulting in low bias voltage dependence, and high $V_h\;and\;V_{bd}$ compared with the values of the traditional CoFe-based MTJ.

• The Journal of Sustainable Design and Educational Environment Research
• /
• v.21 no.1
• /
• pp.1-10
• /
• 2022

To understand the level of disability-free environment in existing high schools, this study evaluated the level of application of facilities for the disabled at 177 high schools located in Seoul and suggested the direction of improving the physical environment of high schools. Detailed standards related to school facilities such as the Act on the guarantee of convenience promotion for persons with disabilities, senior citizens, pregnant women and nursing mothers, and the Act on the prohibition of discrimination against persons with disabilities were examined, and previous studies related to the subject were reviewed. The overall application level of facilities for the disabled was investigated by conducting a field survey of high schools, and the application level was analyzed by the period before and after the enforcement of the Acts and by the presence or absence of special classes.

• Advances in materials Research
• /
• v.1 no.2
• /
• pp.115-128
• /
• 2012

The structural and electrical properties of $(1-x)Ba(Sm_{1/2}Nb_{1/2})O_3-xBaTiO_3$; ($0{\leq}x{\leq}1$) ceramics were prepared by conventional ceramic technique at $1375^{\circ}C$/7 h in air atmosphere. The crystal symmetry, space group and unit cell dimensions were derived from the X-ray diffraction (XRD) data using FullProf software whereas crystallite size and lattice strain were estimated from Williamson-Hall approach. XRD analysis of the compound indicated the formation of a single-phase cubic structure with the space group Pm m. Dielectric study revealed that the compound $0.75Ba(Sm_{1/2}Nb_{1/2})O_3-0.25BaTiO_3$ is having low and ${\varepsilon}^{\prime}$ and ${\varepsilon}^{{\prime}{\prime}}$ a low $T_{CC}$ (< 5%) in the working temperature range (up to+$100^{\circ}C$) which makes this composition suitable for capacitor application and may be designated as 'Stable Low-K' Class I material as per the specifications of the Electronic Industries Association. The correlated barrier hopping model was employed to successfully explain the mechanism of charge transport in the system. The ac conductivity data were used to evaluate the density of states at Fermi level, minimum hopping length and apparent activation energy of the compounds.

• Journal of The Korea Institute of Healthcare Architecture
• /
• v.19 no.2
• /
• pp.7-17
• /
• 2013

Purpose: This basic research tries to provide planning concept of elderly housing which can cope with the needs of the aged society. Methods: This study has been conducted mainly by literature investigation research. Previous researches include Universal and Barrier-Free Design, Elderly Housing Standards, Elderly Welfare Act and other related acts, various papers related to elderly housing, and so on. To set up the Planning concept of elderly housing, elements or indices of previous studies have been comparatively analysed. Results: Elderly housing has been divided into individual type, group type and facility type according to the residents' health and operation system of the housing. This paper focuses on the individual type among three categories. Seven concepts of the elderly housing have been derived as the outcome of this research - Safety, Accessibility, Amenity, Distinguishment, Adaptability, Convenience, and Sociality. Implications: This concept will provide the planning direction on the construction and renovation for Elderly Housing in the future.

• Journal of The Korea Institute of Healthcare Architecture
• /
• v.19 no.2
• /
• pp.41-49
• /
• 2013

Purpose: Economic and social pressures are driving Korea to reform its mental health services. However, it is not easy for the governments to find to the proper method for the mental health service network. This study is to find the mental health service network in Japan. Methods: The survey was conducted by researches and field studies. 1) Researches for mental health service network and facilities. 2) Field study is for Mental Health and Welfare Network in Tokyo. Results: The result of this study can be summarized into three points. The first one, Reform measures are beginning to promote the concept of "normalization" in japanese society. The second one, Facilities of Mental health and welfare system designed by level that can be providing places for people with mental problems. The third one, Facilities consist of barrier-free environment for people with mental problems.