• Macromolecular Research
• /
• v.17 no.5
• /
• pp.319-324
• /
• 2009

A new $\pi$-conjugated polymer, poly[(2-methoxy-(5-(2-(4-oxyphenyl)-5-phenyl-1,3,4-oxadiazole)-hexyloxy))-1,4-pheny1ene-1,2-etheny1ene-alt-(10-hexyl-3,7-phenothiazine )-1,2-ethenylene] (PTOXDPPV), was synthesized by the Heck coupling reaction. The electron transporting unit, conjugated 1,3,4-oxadiazo1e (OXD), is attached on the main chain via linear 1,6-hexamethylenedioxy chain. The band gap and photoluminescence (PL) maximum of PTOXDPPV are 2.35 eV and 565 nm, respectively. These values are very close to those of po1y[(2,5-didecyloxy-1,4-phenylene-1,2-etheny1ene )-alt-(l0-hexyl-3,7-phenothiazine)-1,2-ethenylene] (PTPPV), which does not have OXD pendant. The estimated HOMO energy level of PTOXDPPV was -4.98 eV, which is very close to that of PTPPV (-4.91 eV). The maximum wavelength of EL device based on PTOXDPPV and PTPPV appeared at 587 and 577 nm, respectively. In the PL and EL spectrum, the emission from OXD pendant was not observed. This indicates that the energy transfer from OXD pendants to main chain is occurred completely. The EL device based on PTOXD-PPV (ITO/PEDOT/PTOXDPPV/AI) has an efficiency of 0.033 cd/A, which is significantly higher than the device based on PTPPV (ITO/PEDOT/PTPPV/AI) ($4.28{\times}10^{-3}\;cd/A$). From the results, we confirm that the OXD pendants in PTOXDPPV facilitate hole-electron recombination processes in the emissive layer effectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.7
• /
• pp.786-795
• /
• 2010

In this paper, we propose a new EBG structure that the two unit cells are connected by the bridge line in signal transmission plane. The SSN of the power plane is reduced effectively by via holes and bridge lines connecting the unit cells. The superior signal transfer characteristic is shown between the signal lines in the signal transmission plane. The proposed EBG structure contains 1.2 GHz cut-off frequency and less than －30 dB suppression in the 8.3 GHz broad bandwidth. In addition, To improve the SI(Signal Integrity) in signal transmission plane keeping the same bandstop frequency range, the optimized location of the reference plane is proposed.

• Journal of the Korean institute of surface engineering
• /
• v.53 no.1
• /
• pp.9-14
• /
• 2020

CuS (copper sulfide) thin films having the same thickness of 100nm were deposited on the glass substrates using by radio frequency (RF) magnetron sputtering method. RF powers were applied as a process variable for the growth of CuS thin films. The structural and optical properties of CuS thin films deposited under different power conditions (40-100W) were studied. XRD analysis revealed that all CuS thin films had hexagonal crystal structure with the preferential growth of (110) planes. As the sputtering power increased, the relative intensity of the peak with respect to the (110) planes decreased. The peaks of the two bands (264cm^-1 and 474cm^-1) indicated in the Raman spectrum exactly matched the typical spectral values of the covellite (CuS). The size and shape of the grains constituting the surface of the CuS thin films deposited under the power condition ranging from 40W to 80W hardly changed. However, the spacing between crystal grains tended to increase in proportion to the increase in sputtering power. The maximum transmittance of CuS thin films grown at 40W to 80W ranged from 50 % to 51 % based on 580nm wavelength, and showed a relatively small decrease of 48% at 100W. The band gap energy of the CuS thin films decreased from 2.62eV (at 40W) to 2.56eV (at 100W) as the sputtering power increased.

• Journal of the Korean institute of surface engineering
• /
• v.47 no.5
• /
• pp.239-243
• /
• 2014

The electrical and optical properties of amorphous In-Tin-Zinc-Oxide(ITZO) deposited at room temperature using rf-magnetron sputtering were investigated. The amorphous ITZO thin films were obtained at the composition of In:Sn:Zn = 6:2:2, 4:3:3, and 2:4:4, but the ITZO (8:1:1) showed a crystalline phase of bixbyite structure of In2O3. The resistivity of ITZO could be controlled by oxygen pressure in the sputtering ambient. The resistivity of post-annealed ITZO thin films exhibited the dependence on the amount of Indium. Optical energy band gap and transmittance increased as the amount of indium in ITZO increased. For the device application with ITZO, the bottom-gated thin-film transistor using ITZO as a active channel layer was fabricated. It showed a threshold voltage of 1.42V and an on/off ratio of $5.63{\times}10^7$ operated with saturation field-effect mobility of $14.2cm^2/V{\cdot}s$.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.24 no.6
• /
• pp.229-236
• /
• 2014

A stoichiometric mixture of evaporating materials for $MnAl_2S_4$ single crystal thin films was prepared from horizontal electric furnace. To obtain the single crystal thin films, $MnAl_2S_4$ mixed crystal was deposited on thoroughly etched semi-insulating GaAs(100) substrate by the Hot Wall Epitaxy (HWE) system. The source and substrate temperatures were $630^{\circ}C$ and $410^{\circ}C$, respectively. The crystalline structure of the single crystal thin films was investigated by the photoluminescence and double crystal X-ray diffraction (DCXD). The temperature dependence of the energy band gap of the $MnAl_2S_4$ obtained from the absorption spectra was well described by the Varshni's relation, $E_g(T)=3.7920eV-5.2729{\times}10^{-4}eV/K)T^2/(T+786 K)$. In order to explore the applicability as a photoconductive cell, we measured the sensitivity (${\gamma}$), the ratio of photocurrent to dark current (pc/dc), maximum allowable power dissipation (MAPD) and response time. The results indicated that the photoconductive characteristic were the best for the samples annealed in S vapour compare with in Mn, Al, air and vacuum vapour. Then we obtained the sensitivity of 0.93, the value of pc/dc of $1.10{\times}10^7$, the MAPD of 316 mW, and the rise and decay time of 14.8 ms and 12.1 ms, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.327-327
• /
• 2009

ZnO with a large band gap (~3.37 eV) and exciton binding energy (~60 meV), is suitable for optoelectronic applications such as ultraviolet (UV) light emitting diodes (LEDs) and detectors. However, the ZnO-based p-n homojunction is not readily available because it is difficult to fabricate reproducible p-type ZnO with high hall concentration and mobility. In order to solve this problem, there have been numerous attempts to develop p-n heterojunction LEDs with ZnO as the n-type layer. The n-ZnO/p-GaN heterostructure is a good candidate for ZnO-based heterojunction LEDs because of their similar physical properties and the reproducible availability of p-type GaN. Especially, the reduced lattice mismatch (~1.8 %) and similar crystal structure result in the advantage of acquiring high performance LED devices. In particular, a number of ZnO films show UV band-edge emission with visible deep-level emission, which is originated from point defects such as oxygen vacancy, oxygen interstitial, zinc interstitial[1]. Thus, defect-related peak positions can be controlled by variation of growth or annealing conditions. In this work, the undoped ZnO film was grown on the p-GaN:Mg film using RF magnetron sputtering method. The undoped ZnO/p-GaN:Mg heterojunctions were annealed in a horizontal tube furnace. The annealing process was performed at $800^{\circ}C$ during 30 to 90 min in air ambient to observe the variation of the defect states in the ZnO film. Photoluminescence measurements were performed in order to confirm the deep-level position of the ZnO film. As a result, the deep-level emission showed orange-red color in the as-deposited film, while the defect-related peak positions of annealed films were shifted to greenish side as increasing annealing time. Furthermore, the electrical resistivity of the ZnO film was decreased after annealing process. The I-V characteristic of the LEDs showed nonlinear and rectifying behavior. The room-temperature electroluminescence (EL) was observed under forward bias. The EL showed a weak white and strong yellowish emission colors (~575 nm) in the undoped ZnO/p-GaN:Mg heterojunctions before and after annealing process, respectively.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.5
• /
• pp.1451-1456
• /
• 2012

A novel tetrathiafulvalene (TTF)-based main-chain polymer (6TTF-polymer) was successfully synthesized via a condensation polymerization between a newly synthesized dihydroxy TTF derivative and a malonyl chloride, and its chemical structure was characterized by spectroscopic techniques. Molecular weight of the 6TTF-polymer (9,030 g/mol by gel permeation chromatography) was large enough to form the ductile film. The electrochemical and optical properties of the 6TTF-polymer were further estimated by cyclic voltammetry, ultraviolet and photoluminescence spectroscopes. The highest occupied molecular orbital level ($E_{HOMO}$=-4.79 eV) and band-gap energy ($E_g$=1.91 eV) of the 6TTF-polymer suggested that TTF-based polymer could act as a good electron donating material for the optoelectronic applications.

• Journal of the Korean Electrochemical Society
• /
• v.17 no.1
• /
• pp.1-6
• /
• 2014

This review article summarizes photoelectrochemical water splitting using gallium nitride (GaN). GaN materials have been studied as novel photoelectrode material due to its chemical stability and easy band gap engineering. Unlike other semiconductor materials that are easily corroded in strongly acidic or alkaline electrolyte, n-type GaN is chemically stable enough to be used as photoanode in oxygen evolution reaction. Furthermore, studies on p-type GaN have been recently reported. This review briefly discusses problems that need to be solved before GaN materials find widespread use in solar fuel application.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.7
• /
• pp.584-588
• /
• 2011

The ZnO thin films doped with Ga and Ge (GZO:Ge) were prepared on glass substrate using RF sputtering system. Structural, morphological and optical properties of the films deposited in different temperatures were studied. Proportion of the element of using target was 97 wt% ZnO, 2.5 wt% Ga and 0.5 wt% Ge with 99.99% highly purity. Structural properties of the samples deposited in different temperatures with 200 w RF power were investigated by field emission scanning electron microscopy, FE-SEM images and x-ray diffraction XRD analysis. Atomic force microscopy, AFM images were able to show the grain scales and surface roughness of each film rather clearly than SEM images. it was showed that increasing temperature have better surface smoothness by FE-SEM and AFM images. Transmittance study using UV-Vis spectrometer showed that all the samples have highly transparent in visible region (300~800 nm). In addition, it can be able to calculate bandgap energy from absorbance data obtained with transmittance. The hall resistivity, mobility, and optical band gap energy are influenced by the temperature.

• Korean Journal of Materials Research
• /
• v.29 no.12
• /
• pp.764-773
• /
• 2019

The gas response characteristic toward C₂H₅OH has been demonstrated in terms of copper-vacancy concentration, hole density, and microstructural factors for undoped/Li(I)-doped CuO thin films prepared by sol-gel method. For the films, both concentrations of intrinsic copper vacancies and electronic holes decrease with increasing calcination temperature from 400 to 500 to 600 ℃. Li(I) doping into CuO leads to the reduction of copper-vacancy concentration and the enhancement of hole density. The increase of calcination temperature or Li(I) doping concentration in the film increases both optical band gap energy and Cu2p binding energy, which are characterized by UV-vis-NIR and X-ray photoelectron spectroscopy, respectively. The overall hole density of the film is determined by the offset effect of intrinsic and extrinsic hole densities, which depend on the calcination temperature and the Li(I) doping amount, respectively. The apparent resistance of the film is determined by the concentration of the structural defects such as copper vacancies, Li(I) dopants, and grain boundaries, as well as by the hole density. As a result, it is found that the gas response value of the film sensor is directly proportional to the apparent sensor resistance.