• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.3
• /
• pp.465-469
• /
• 2019

In this paper, the design of BLDC (brushless direct current) motors based on torque and back-EMF equations was carried out to assess the application of the motor in concrete vibrators. The air gap flux density of the motor is an important parameter because the length of the motor and the size of the diameter are given. The air gap magnetic flux density was calculated through a simplified magnetic circuit, and basic design of the shape and dimensions of the motor were then determined by carrying out experiments based on torque, back-EMF, and air magnetic flux density equations. After setting the outer and inner diameters, stack lengths, and rated speed of the motor, a detailed design was performed by simulations using the finite element method by designating the diameter and thickness of the motor as the key parameters. The final design to satisfy the target torque and the lowest THD (Total Harmonic Distortion) was carried out along with a simulation.

• Journal of IKEEE
• /
• v.22 no.3
• /
• pp.759-766
• /
• 2018

This paper presents a high-speed axial-flux machine which utilizes the idea of sinusoidal shaped pole combined with a consequent iron-pole. The target of the proposed machine is the cost reduction of the relatively expensive Samarium-Cobalt (SmCo) permanent magnet (PM) material and the torque per PM volume improvement by using sinusoidal consequent-pole rotor. The effectiveness of the proposed machine is validated by comparing it with conventional consequent-pole and with conventional PM machines using 3-D finite element method (FEM) simulations. The comparison and analysis is done in terms of back electro-motive force (back-EMF) harmonic contents, torque per PM volume and torque ripple characteristics. The simulation results show that the proposed machine is suitable and cost-effective for high-speed and high torque per PM volume applications. Furthermore, due to the consequent pole, the magnetic flux saturation and the overload current torque-capability are also presented and discussed in the paper.

• Journal of Power Electronics
• /
• v.18 no.6
• /
• pp.1708-1719
• /
• 2018

A complete current loop decoupling control strategy based on a sliding mode observer (SMO) is proposed to eliminate the influence of current dynamic coupling and back electromotive force (EMF) in the vector control of permanent magnet synchronous motors. With this strategy, current dynamic decoupling and back EMF compensation can be simultaneously achieved. Unlike conventional methods, the proposed strategy can avoid the disturbances caused by the parametric variations of motor systems and maintain the advantages of proportional integral (PI) controllers, which are robust and easy to operate. An improved SMO, which uses a special PI regulator other than a linear saturation function as the equivalent control law in the boundary layer of a sliding surface, is proposed to eliminate the estimated errors caused by the quasi-sliding mode and obtain a satisfactory decoupling performance. The stability and parameter robustness of the proposed strategy are also analyzed. Physical experimental results are presented to verify the validity of the method.

• 제어로봇시스템학회:학술대회논문집
• /
• 1988.10a
• /
• pp.148-153
• /
• 1988

In this study, the stabilization of moving sight using a gyro is investigated. At first, Linear Compensator was design by linearizing gyro, torque motor and several parameters from a given required frequency response curve. By using this, System Control Performance was analyzed by back EMF, torque saturation and Coulomb friction effects. Also stabilization Performance by disturbances and Paramter variations were simulated.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.1
• /
• pp.466-471
• /
• 2017

Pantograph must be correctly attached to catenary to continuously supply stable power to railway vehicle, and the device used here is Auxiliary Air Compressor (ACM). The existing ACM used the DC motor that included commutator and brush. Since maintenance and repair by mechanical friction are essential for the DC motor, BLDC motor studies have been conducted to improve this. A three-phase BLDC motor does $120^{\circ}$ two-phase commutation through hall sensors in general. However, since hall sensor is vulnerable to heat and can run only when all three sensors work normally, sensorless control method has been studied to solve this. Using back EMF Zero Crossing Point (ZCP) detection method, this paper will introduce a stable switching sensing method that has a non-commutation area in a low speed zone.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.3
• /
• pp.195-202
• /
• 2004

This paper presents a current control strategy to reduce torque ripple of Brushless DC Motor during con)mutation. The torque ripple is mainly caused by the inequality in the rate of change between rising current and decaying one during commutation. And also it is influenced by the shape of real back EMF Therefore, in the proposed control strategy, considering real back EMF a compensation voltage is generated to equalize the rate of change in these commutating currents. And then, by providing the compensation voltage during commutation, the torque ripple can be reduced. The simulation md experimental results verify that the proposed method can reduce the torque and the current ripples significantly.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.7 no.6
• /
• pp.34-41
• /
• 1993

This paper describes an effort to develop a microcomputer-based parameter identification system for three phase and two phase brushless DC motor. Back EMF equation is derived from back EMF waveform of three phase and two phase brushless DC motor. In this paper, a new identification algorithm for the brushless DC motor parameters by Pasek's technique is de veloped. It is found that Pasek's equation is valid for the brushless DC motor, too. The results obtained clearly shows that it is possible to implement the identification system for the determination of the brushless DC motor parameters. To minimize errors due to the ripple component in the measured armature current, dlgital averaging filter is employed. The whole identification process of signal generation, measuring, parameter determination is fully automated. The use of the pmpased method in the parameter identification system shows that the averaged current curve is in excellent agreement with the estimated current curve. Therefore, this close agreement conf i i the validity of this technique.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.3
• /
• pp.223-230
• /
• 2001

This power proposes a new sensorless drive system for the trapezoidal brushless DC motor generally requiring mechanical position or speed sensor. For this an indirect rotor position sensing method from the back emf waveform of non-conducting phase is explained. Back emf waveform of non-conducting is obtained from analysing terminal voltage created by making Y-connection. And an experiment is implemented with a driving system which use 87c196mc microcontroller having a peripheral associated with 3-phase signals and inverter composed of Power MOSFET. The experimental results show the validity and practicality of the proposed sensorless drive.

• Journal of Power Electronics
• /
• v.18 no.5
• /
• pp.1424-1433
• /
• 2018

This paper presents a novel space vector pulse-width modulation (SVPWM) to synthesize an arbitrary non-sinusoidal phase voltage. The key of the proposed method is that the switching vectors used to comprise the reference vectors in the ${\alpha}_1-{\beta}_1$ frame and the ${\alpha}_3-{\beta}_3$ frame are decoupled. In the ${\alpha}_1-{\beta}_1$ frame, the reference vector is comprised by near two large vectors. The corresponding vector comprised by the two vectors in the ${\alpha}_3-{\beta}_3$ frame is considered as a disturbance, which is restrained by close-loop control. In the ${\alpha}_3-{\beta}_3$ frame, there are two methods to comprise the reference vector. Method I is a near two middle vectors method. Method II uses near four vectors (two middle and two little vectors). The proposed SVPWM using decoupled switching vectors can guarantee a maximum modulation index in the ${\alpha}_1-{\beta}_1$ frame. The effectiveness of the proposed method is verified by simulated and experimental results under various operation conditions.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.59 no.2
• /
• pp.135-140
• /
• 2010

This paper presents a sensorless speed control of BLDC Motor using terminal voltage of the one phase. Rotor position information is extracted by indirectly sensing the back EMF from only one of the three terminal voltages for a three-phase BLDC motor. Depending on the terminal voltage sensing rotor position, active filter is used for position information. This leads to a significant reduction in the component device of the sensorless circuit. Therefore this is a advantage for the cost saving and size reduction. With indirect sensing methods based on detection of the terminal voltage that require active filtering, the position information needs the six divider section by PLL circuit, the binary counter and johnson counter by the EPLD. Finally, this algorithm can estimate the rotor position information similar to Hall-sensor sticked the three-phase BLDC motor. As a result, the method described that it is not sensitive to filtering delays, allowing the motor to achieve a good performance over a wide speed range. In addition, a simple starting method and a speed estimation approach are also proposed. Experimental and simulation results are included to verify the proposed scheme.