• Journal of Mechanical Science and Technology
• /
• 제17권4호
• /
• pp.599-605
• /
• 2003

For practical calculations, the Reynolds equation is frequently used to analyze the lubricating flow. The full Navier-Stokes Equations are used to find validity limits of Reynolds equation in a lubricating flow regime by result comparison. As the amplitude of wavy upper wall increased at a given average channel height, the difference between Navier-Stokes and lubrication theory decreased slightly : however, as the minimum distance in channel throat increased, the differences in the maximum pressure between Navier-Stokes and lubrication theory became large.

• 한국자동차공학회논문집
• /
• 제3권6호
• /
• pp.55-68
• /
• 1995

Approximately 30 to 70 % of the mechanical losses in a reciprocating engine are contributed by the friction at the piston ring-cylinder interface. The friction characteristics of the piston ring during engine operation is known to as mixed lubrication experimentally. The mixed lubrication models based on the Average Reynolds Equation have been used by this time in order to study the tribological performance of the ring. However, the Average Reynolds Equation contains the expected value term(${\bar{h}}_r$) of local film thickness as well as nominal film thickness(h), so that the work of numerically solving ${\bar{h}}_r$ must be included to obtain the pressure in the oil film. The process of solving ${\bar{h}}_T$ causes a greater multiplying in the numerical solution. In this paper the mixed lubrication analysis using the Simplified Average Reynolds Equation in the piston ring is presented. This equation has only h as oil film thickness term. Therefore the tedious numerical procedure required to obtain ${\bar{h}}_T$ is not needed, and also, computation time can be reduced.

• Tribology and Lubricants
• /
• 제29권1호
• /
• pp.27-32
• /
• 2013

This study examined the effects of surface roughness in the mixed lubrication regime of smooth and rough surfaces for roller bearings. The average flow model was adopted for interaction between the flow rheology of the lubricant and the surface roughness. The average Reynolds equation and related flow factor that describes the coupled effects of surface roughness and flow rheology, the viscosity-pressure and density-pressure equations, the elastic deformation equation, and the force balance equation were solved simultaneously. The results showed that the effects of surface roughness on the film thickness and pressure distribution should be considered, especially in elastohydrodynamic lubrication contact problems.

• Tribology and Lubricants
• /
• 제27권6호
• /
• pp.326-331
• /
• 2011

The purpose of this paper is to analyze and discuss the effects of surface roughness by comparing the elastohydrodynamic lubrication(EHL) analysis of smooth surface and rough surface as the ball bearing. In order to do this, The average flow model is adapted for the interaction of the flow rheology of lubricant and surface roughness. The average Reynolds equation and the related flow factor which describes the coupled effects of surface roughness and flow rheology, the viscosity-pressure and density-pressure relations equations, the elastic deformation equation, and the force balance equation are solved simultaneously. The results show that effects of surface roughness on the film thickness and pressre distribution should be considered especially in EHL contact problems.

• 대한기계학회논문집B
• /
• 제32권6호
• /
• pp.471-478
• /
• 2008

Detached Eddy Simulation (DES) is performed for developing turbulent flow of the $270^{\circ}$ curved duct at a Reynolds number of 56,690. The curvature ratio on the basis of a centric radius $R_c$ and a duct height H is 3.357. Turbulence models adopted are k-$\omega$ model for Reynolds Average Navier-Stokes (RANS) equation Simulation and Shear Stress Transport (SST) model for DES. DES is used as the hybrid computation technique combined with RANS-SST and Large Eddy Simulation (LES). Predicted results are compared with measured results including the distributions of Reynolds stresses and the flow characteristics on the symmetric plane of curved duct are presented. Judging from the comparison between the predicted and the measured results, the DES approach is applicable to calculate the developing turbulent flow in a $270^{\circ}$ curved duct.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2007년도 동계학술발표대회 논문집
• /
• pp.558-563
• /
• 2007

Detached Eddy Simulation(DES) is performed for turbulent flow of the $270^{\circ}$ bend at a Reynolds number of 56,690. A Fine grid generation is used near a wall in order to satisfy the wall boundary condition of y+<1. Turbulence models adopted for DES and Reynolds Average Navier Stokes(RANS) simulation are SST(Shear Stress Transfort) model. Solutions for both streamwise and circumferential velocity components are compared with the experimental data by Lee for $270^{\circ}$ bend and by Chang for $180^{\circ}$ bend.

• Tribology and Lubricants
• /
• 제20권5호
• /
• pp.284-291
• /
• 2004

We present a three-dimensional average flow model considering elastic deformation of pad asperities for chemical mechanical planarization. To consider the contact deformation of pad asperities in the calculation of the flow factor, three-dimensional contact analysis of a semi-infinite solid based on the use of influence functions is conducted from computer generated three dimensional roughness data. The average Reynolds equation and the boundary condition of both force and momentum balance are used to investigate the effect of pad roughness and external pressure conditions on film thickness and wafer position angle.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2000년도 제31회 춘계학술대회
• /
• pp.134-141
• /
• 2000

The real area of contacts, average film thickness, mean real pressure, and mean hydrodynamic pressure are investigated numerically in this study, especially for the parallel thrust bearing. Model surface is generated numerically with given autocorrelation function and some surface profile parameters. Then the average Reynolds equation contained flow factors and contact factor is applied to predict the effects of surface roughness in mixed lubrication regimes. In this equation, flow factors are defined as correction terms to smooth out high frequency surface roughness and contact factor is introduced to relieve from obtaining the average film thickness. Therefore the computation time to obtain h can be reduced.

• Tribology and Lubricants
• /
• 제16권6호
• /
• pp.455-460
• /
• 2000

The real area of contacts, average film thickness, mean real pressure, and mean hydrodynamic pressure are investigated numerically in this study, especially for the parallel thrust bearing. Model surface is generated numerically with given autocorrelation function and some surface profile parameters. Then the average Reynolds equation contained flow factors and contact factor is applied to predict the effects of surface roughness in mixed lubrication regimes. In this equation, flow factors are defined as correction terms to smooth out high frequency surface roughness and contact factor is introduced to relieve from obtaining the average film thickness. Therefore the computation time to obtain barh h can be reduced.

• KSTLE International Journal
• /
• 제3권1호
• /
• pp.7-11
• /
• 2002

The roughness effects are very important due to the presence of interacting asperities in mixed lubrication regime. An average Reynolds equation using flow factors is useful to determine the effects of surface roughness on mixed lubrication. In this study, the effect of kurtosis on flow factors is investigated using random rough surfaces generated numerically, The results show that flow factors are very sensitive to h/$\sigma$ according to the value of kurtosis in the partial lubrication regime.