• 한국자동차공학회논문집
• /
• 제19권5호
• /
• pp.67-75
• /
• 2011

A new energy absorbing mechanism for car seat was developed to reduce the neck injury in rear impacts. Energy absorbing principle is based on the shear-bolt behavior of thin-walled cast components subjected to static and dynamic loads. Results of shear bolt test using AM60 of Mg alloys showed robust behavior giving an approximately constant mean force during failure processes. Simply designed energy absorbing mechanism was assembled with the recliner between seat backs and seat rails. We have simulated the sled test of seat with dummy under the rear end impact using the finite element method. Results of simulation show that the new seat mechanism reduces thorax acceleration to a considerable extent, but it is not sufficient to mitigate neck injury indices e.g. neck shear force, neck tension force and NIC. With heightened headrest and narrowed backset, the energy absorbing mechanism resulted in good performance of protecting the neck injuries.

• 한국산학기술학회논문지
• /
• 제11권9호
• /
• pp.3168-3175
• /
• 2010

럼버 서포트는 허리에 가해지는 압력을 지지하여 장시간 운전시 피로감을 해소하는 자동차 시트의 부품이다. 본 연구에서는 자동차 시트의 럼버 서포트를 모델링 하였으며, 해석은 럼버 서포트의 베드부분에 여러 가지의 비드를 보강하여 사람이 자동차 시트에 앉아 있을 때 작용하는 하중에 따른 변형에 대해 구조해석을 하여 안락성면에서 적합한 모델을 찾는 것이 주된 목적이다. 5줄 보강타입과 풀타입이 5mm안쪽의 변형과 500 N의 접촉력이 나타나 승객의 안락감에 있어 가장 적합하고 내구성도 양호한 것으로 사료된다.

• 한국자동차공학회논문집
• /
• 제13권3호
• /
• pp.58-63
• /
• 2005

In order to minimize weight of vehicle seat, an optimum design of aluminum seat is presented while satisfying stress and fatigue life constraints. In this study, the analysis model is validated by comparing it's stress with that of test. Then, two-level orthogonal array is used to estimate the design sensitivity for 7 design variables. Finally, the sequential approximate optimization (SAO) is performed using the constructed RSM models. The approximate RSM models are sequentially updated using the analysis results corresponding to the approximate optimum obtained during the SAO. After 14 analyses, the SAO gives an optimal design that can reduce 16.7$\%$ of weight while increasing 369$\%$ of fatigue life and satisfying stress constraint.

• 한국자동차공학회논문집
• /
• 제14권5호
• /
• pp.155-163
• /
• 2006

Car seat is one the most important element to make comfortable drivability. It can absorb the impact or vibration during driving state. In addition to those factors, it is needed to have enough strength for passenger safety. From energy efficiency and environmental point of view lighter passenger car seat frame becomes hot issue in the auto industry. In this paper, weight optimization methodology is investigated for commercial car seat frame using CAE. Optimized designs for seat frame are developed using commercially available finite element code(ANSYS) and design of experiment method. At first, car seat frame is modelled using 3-D computer aided design tool(CATIA) and simplified for finite element modelling. Finite element analysis is carried out for the case of FMVSS 202 Head Restraint test to check the strength of the original seat frame. Two base brackets are selected as optimized elements that are the heaviest parts in the seat frame. After finite element analysis for the brackets with similar load condition to the previous test optimization technique is applied for 10% to 50% weight reduction. Design of experiment is utilized to obtain optimization design for the bracket based on the modified 50% weight reduction model in which outer shape of the bracket is conserved. Weight optimization models result in the decrease of the strength in spite of weight reduction. The more design points should be considered to get better optimized model. The more advanced optimization technique may be utilized for more parts of the seat frame to increase whole seat frame characteristics in the future.

• 소성∙가공
• /
• 제23권2호
• /
• pp.75-81
• /
• 2014

Progressive dies are used for metal stamping during which multiple operations are performed in a sequence. Material is fed automatically from a coil into the press and advances from one die station to the next with each press stroke. Transfer dies are used in high-volume manufacturing for round, deep-drawn, and medium-to-large parts. Several different operations may be incorporated within a transfer die such as blanking, bending, piercing, trimming, and deep drawing. The main challenge in the current study is how to deform a seat cushion panel meeting the design specifications without any defects. A complex automation die manufacturing technology for the automotive seat cushion panel, mixing both semi-progressive die and transfer die for continuous production, was developed.

• 한국자동차공학회논문집
• /
• 제12권3호
• /
• pp.130-138
• /
• 2004

In this paper, the structural strength of a rolling stock seat were numerically evaluated under several design load conditions based on the UIC requirements. The rot]ins stock seat was designed for the high speed train of a Chinese conventional line. To maximize its weight reduction and structural strength, an aluminium alloy, ALDC8-T5, was applied to the base frame, side frames and armrests. The designed seat frame satisfied the strength requirements on inertia loads and fatigue test conditions. However, it couldn't satisfy the requirements on the static test conditions of UIC 566 OR. Therefore, some design modifications were suggested and numerically evaluated whether the static test requirements could be satisfied or not.

• 한국기계가공학회지
• /
• 제15권5호
• /
• pp.137-144
• /
• 2016

This paper aims to ensure describe the a spring-back prevention technique for improving shape fixability by using an ultra-high strength steel sheet with 980 MPa to develop a lightweight seat rail parts. Ultra-high strength steel gives a potential for considerable weight reduction and a cost-effective way to produce energy efficient vehicles. The influence of a spring-back of seat rail parts on the shape fixability in forming processes was investigated to be solved by an adjustment of the appropriate tool design and process parameters. The computed results for improving shape fixability were in good agreement with the experimental results.

• 소성∙가공
• /
• 제24권6호
• /
• pp.400-404
• /
• 2015

For mass production of stamped parts, which require complicated in-press operations, it is always advisable to use a progressive die set. It is difficult to choose a progressive die set if the stamped parts need to be deep drawn and especially if they are unsymmetrical. Because unsymmetrical deep drawing parts are very sensitive to the effect of weight during moving to the next step, they are hard to exactly locate on the die face. An automotive seat side cushion panel is about 80mm high, unsymmetrical and its low edge needs hemming, so it is hard to produce even using a progressive die set. In the current paper a progressive stamping for seat side cushion panel was examined. Five strip bridges were considered to be strong enough to move to the next die as predicted by the CAE analysis.

• 한국자동차공학회논문집
• /
• 제13권3호
• /
• pp.24-34
• /
• 2005

The automobile seat must satisfy various safety regulations for the passenger's safety. In many design practices, each component is independently designed by concentrating on a single related regulation. However, since multiple regulations can be involved in a seat component, there may be design confliction among the various safety regulations. Therefore, a new design methodology is required to effectively design an automobile seat. The axiomatic approach is employed for considering multiple regulations. The Independence Axiom is used to define the overall flow of the seat design. Functional requirements (FRs) are defined by safety regulations and components of the seat are classified into groups which yield design Parameters (DPs). The classification is carried out to have independence in the FR-DP relationship. Components in a DP group are determined by using orthogonal away of the design of experiments (DOE). Numerical analyses are utilized to evaluate the safety levels by using a commercial software system for nonlinear transient finite element analysis.

• 한국자동차공학회논문집
• /
• 제23권2호
• /
• pp.185-190
• /
• 2015

The purpose of this study is developing the quantify the seat belt pulling Noise index and evaluation method. This paper presents the objective method to evaluate the emotional feeling about the pulling Noise of the seat belt. The physical quantification is required to objectively evaluate the emotional feeling of the pulling Noise. This is called the "Noise metric." The Noise metric is should correlated to the subjective rating of the pulling Noise. The pulling Noise index is developed throughout the linear regression of the Noise metric and the subjective rating. The developed index is used for the objective evaluation of the emotional feeling about the pulling Noise of a seat belt throughout the modification of seat belt components.