• International Journal of Automotive Technology
• /
• 제3권2호
• /
• pp.71-78
• /
• 2002

A new control method far vision-based autonomous vehicle is proposed to determine navigation direction by analyzing lane information from a camera and to navigate a vehicle. In this paper, characteristic featured data points are extracted from lane images using a lane recognition algorithm. Then the vehicle is controlled using new Levenberg-Marquardt neural network algorithm. To verify the usefulness of the algorithm, another algorithm, which utilizes the geometric relation of a camera and vehicle, is introduced. The second one involves transformation from an image coordinate to a vehicle coordinate, then steering is determined from Ackermann angle. The steering scheme using Ackermann angle is heavily depends on the correct geometric data of a vehicle and a camera. Meanwhile, the proposed neural network algorithm does not need geometric relations and it depends on the driving style of human driver. The proposed method is superior than other referenced neural network algorithms such as conjugate gradient method or gradient decent one in autonomous lateral control .

• 한국추진공학회지
• /
• 제23권2호
• /
• pp.38-45
• /
• 2019

본 연구에서는 항공용 가스터빈의 연소실에서의 연소불안정 해석을 위한 고유값 도출을 목적으로 하는 1D 네트워크 모델을 개발하였다. 모델은 면적 변화가 있는 음향 네트워크 요소들 사이의 각종 지배 방정식을 통하여 개발되었고, 이를 이용하여 현재 개발 중인 복잡한 유로 형상을 갖는 실제 항공용 가스터빈 연소기에서의 음향장 해석에 적용되었다. 본 모델을 통하여 도출된 음향장 해석 결과는 3차원 유한요소해석 기반의 헬름홀츠 솔버의 계산 결과와 비교하였다.

• 한국자동차공학회논문집
• /
• 제21권1호
• /
• pp.128-136
• /
• 2013

This study presents the development of Gateway Control Module using SAE J1939 protocol for the commercial vehicles. Presently, the load rate of CAN bus is increased by the single network composition and addition of new ECUs for development of intelligent vehicles. Because the embedded system of the integrated network control function has the errors of the CAN bus caused by the increase of ECU, it is needed for development of commercial vehicles. Also, this study presents the development of smart functions that can diagnosis CAN bus errors, fault diagnosis of ECU and basic function that arbitrates CAN bus between ECUs of commercial vehicle. GCM was designed for 4channel separation about Gateway function as solution of load rate decrease and smart functions. HILS(Hardware in the loop simulation)system that can achieve simulation about CAN Messages of all systems on vehicle was applied to evaluate performance and verification of all functions and performance. The load rate on CAN bus was decreased at using functions what was delivery, block and process of GCM. Through this, it was enabled to organize systematic architecture for gateway.

• 드라이브 ㆍ 컨트롤
• /
• 제19권1호
• /
• pp.51-61
• /
• 2022

This paper presents a model-free system based on a framework of a backstepping sliding mode control (BSMC) with a radial basis function neural network (RBFNN) and adaptive mechanism for electro-hydraulic systems (EHSs). First, an EHS mathematical model was dedicatedly derived to understand the system behavior. Based on the system structure, BSMC was employed to satisfy the output performance. Due to the highly nonlinear characteristics and the presence of parametric uncertainties, a model-free approximator based on an RBFNN was developed to compensate for the EHS dynamics, thus addressing the difficulty in the requirement of system information. Adaptive laws based on the actor-critic neural network (ACNN) were implemented to suppress the existing error in the approximation and satisfy system qualification. The stability of the closed-loop system was theoretically proven by the Lyapunov function. To evaluate the effectiveness of the proposed algorithm, proportional-integrated-derivative (PID) and improved PID with ACNN (ACPID), which are considered two complete model-free methods, and adaptive backstepping sliding mode control, considered an ideal model-based method with the same adaptive laws, were used as two benchmark control strategies in a comparative simulation. The simulated results validated the superiority of the proposed algorithm in achieving nearly the same performance as the ideal adaptive BSMC.

• 한국기계가공학회지
• /
• 제21권4호
• /
• pp.46-52
• /
• 2022

In the existing wired communication network, wired communication is frequently interrupted by lightning, which accompanies rain, and remote management cannot be performed when it is actually necessary. In the case of communication interruption, field data stored in the database are lost, and data at an important point in time may go missing; this causes a decrease in the reliability of the stored data. Therefore, in this study, wireless communication using the Internet of Things (IoT) communication network of the 4^th industrial technology is installed in the prototype to reduce wired communication construction costs, prevent resource waste and environmental damage due to communication facility construction, and prepare for communication loss.

• 전기전자학회논문지
• /
• 제22권2호
• /
• pp.518-521
• /
• 2018

차량 내부의 다양한 전자장치를 연결하는 차량 내 통신(IVN: in-vehicle network)은 실시간성, 저잡음성, 고신뢰성, 고유연성 등이 필요하며 CAN(controller area network), CAN-FD(CAN flexible data rate), FlexRay, LIN(local interconnect network), SENT(single edge nibble transmission), PSI5(peripheral sensor interface 5) 등 다양한 기술이 있다. 본 논문에서는 이들 기술의 동작 원리에 대해 살펴보고 각 기술의 적용 대상과 장단점에 대해 설명한다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1991년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 22-24 Oct. 1991
• /
• pp.1006-1011
• /
• 1991

In this paper, a neural network estimator which estimates the output of the wide range oxygen sensor is proposed, The neural network estimator is constructed to give the output of the wide range oxygen sensor from rpm, fuel injection time, throttle position, and output voltage of the exhaust gas oxygen sensor. And, using this estimator, PI controller for air-fuel ratio control is designed. Experiment results show that the proposed method gives good results for SONATA engine under light load and constant rpms.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.76-81
• /
• 2004

Problems with the control, oscillatory motion and compliance of pneumatic systems have prevented their widespread use in advanced robotics. However, their compactness, power/weight ratio, ease of maintenance and inherent safety are factors that could be potentially exploited in sophisticated dexterous manipulator designs. These advantages have led to the development of novel actuators such as the McKibben Muscle, Rubber Actuator and Pneumatic Artificial Muscle Manipulators. However, some limitations still exist, such as a deterioration of the performance of transient response due to the changes in the external inertia load in the pneumatic artificial muscle manipulator. To overcome this problem, a switching algorithm of the control parameter using a learning vector quantization neural network (LVQNN) is newly proposed. This estimates the external inertia load of the pneumatic artificial muscle manipulator. The effectiveness of the proposed control algorithm is demonstrated through experiments with different external inertia loads.

• Journal of Mechanical Science and Technology
• /
• 제18권8호
• /
• pp.1388-1400
• /
• 2004

Problems with the control, oscillatory motion and compliance of pneumatic systems have prevented their widespread use in advanced robotics. However, their compactness, power/weight ratio, ease of maintenance and inherent safety are factors that could be potentially exploited in sophisticated dexterous manipulator designs. These advantages have led to the development of novel actuators such as the McKibben Muscle, Rubber Actuator and Pneumatic Artificial Muscle Manipulators. However, some limitations still exist, such as a deterioration of the performance of transient response due to the changes in the external inertia load in the pneumatic artificial muscle manipulator. To overcome this problem, a switching algorithm of the control parameter using a learning vector quantization neural network (LVQNN) is newly proposed. This estimates the external inertia load of the pneumatic artificial muscle manipulator. The effectiveness of the proposed control algorithm is demonstrated through experiments with different external inertia loads.

• 한국자동차공학회논문집
• /
• 제10권5호
• /
• pp.114-120
• /
• 2002

In a distributed real-time control system, it is essential to confirm the timing behavior of all tasks because these tasks of each real-time controller have to finish their processes within the specified time intervals called a deadline. In order to satisfy this objective, the timing analysis of a distributed real-time system such as shcedulability test must be performed during the system design phase. In this study, a simple application of CAN fur a vehicle body network system is formulated to apply to a holistic scheduling analysis, and the worst-case execution time (WCET) and the worst-case end-to-end response time (WCRT) are evaluated in the point of holistic system view.