• Aerospace Engineering and Technology
• /
• v.13 no.2
• /
• pp.73-79
• /
• 2014

During developing cubesat flight software, Communication test between cubesat and ground station is needed. For this, we have constructed indoor ground station without outdoor antenna for decreasing total cost and time. In this time, if output power of ground station is high, it will affect for cubesat transceiver to be fail. For solving this problem, ground station must be designed for output power of it to be lower than input power of cubesat satellite, and it must be verified. In this paper, first, we describe cubesat indoor ground station using UHF and VHF. Second, we describe output power decreasing test for indoor operation of ground station by attaching attenuators in the end of the output connector.

• ETRI Journal
• /
• v.35 no.3
• /
• pp.378-385
• /
• 2013

An S-band multifunction chip with a simple interface for an active phased array base station antenna for next-generation mobile communications is designed and fabricated using commercial 0.5-${\mu}m$ GaAs pHEMT technology. To reduce the cost of the module assembly and to reduce the number of chip interfaces for a compact transmit/receive module, a digital serial-to-parallel converter and an active bias circuit are integrated into the designed chip. The chip can be controlled and driven using only five interfaces. With 6-bit phase shifting and 6-bit attenuation, it provides a wideband performance employing a shunt-feedback technique for amplifiers. With a compact size of 16 $mm^2$ ($4mm{\times}4mm$), the proposed chip exhibits a gain of 26 dB, a P1dB of 12 dBm, and a noise figure of 3.5 dB over a wide frequency range of 1.8 GHz to 3.2 GHz.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 1996.06a
• /
• pp.27-31
• /
• 1996

In this paper, The SSPA(Solid State Power Amplifier) is 100 watts amplifier which is used with C-Band Satellite communication Up-Link frequency, 5.875 ∼6.425 GHz. SSPA requires more output power than is available from a single GaAs FET with result it is necessary to combine the output of many device. To achieve a high power, it is important to make a good N-way power divider which has a small different phase, good combining efficiency and high power handling capability. The reliability of Power GaAs FET decrease with increasing junction temperature, power amplifier in general dissipate amount of power. It is important to provide them with a heatsink and a temperature compensation circuit to dispose of the unwanted heat. To compensate temperature, Using PIN diode attenuator, it is enable to get a precision gain control. The output power of the SSPA is more than 100 watt with which the TWTA (Traveling-Wave Tube Amplifier) can be replaced. Each stage was measured by the Network analyzer PH8510C, Power meter Booton 42BD, The gain is more than 53 dB, flatness is less than 1.5 dB.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.4 no.3
• /
• pp.45-53
• /
• 1993

The shielding effectiveness of materials is determined by measuring the ratio of the incident electromagnetic power to that which passes through the material under test. The measurement system is constructed using several test fixtures, tracking generator, spectrum analyzer, step attenuator, RF switches, and amplifiers, etc.. The automation of measurements is completed using a personal computer. Especially, incident power, reflected power, and transmitted power are measured with only one spectrum analyzer using a dual directional coupler and RF switches. Therefore the system is to be used in design of shielding materials, as well as shielding effectiveness measurements. This system has dynamic range of more than 120 dB in the frequency range of 10 MHz to 1 GHz, and it can be used to measure shielding effectiveness of composite materials.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.26 no.1
• /
• pp.82-88
• /
• 2017

In 2016, a handmade vehicle called to the VF-3 was designed and manufactured as a formula typed car. Prior to manufacturing and assembly, the impact attenuator was analyzed through ANSYS LS-DYNA, and the results were applied to the VF-3. The dynamical performance of the VF-3, such as the acceleration and circling simulations, was also assessed through MSC-ADAMS. The results were applied and compared after the Korean Society of Automotive Engineers (KSAE) competition. There was only a 0.8 s difference in the acceleration test. In order that the frame was not twisted by thermal deformation, Argon-TIG welding was used and a zig was designed. Another zig was designed to have the exact position for the hardpoints in the suspension system. Most of the parts were made with aluminum 7050 for reduced weight. The VF-3 won the third prize in the 2016 KSAE Student Handmade Vehicle competition.

• Journal of The Institute of Information and Telecommunication Facilities Engineering
• /
• v.5 no.1
• /
• pp.43-59
• /
• 2006

A compact and broadband $4\times1$ array antenna was developed for 3G smart antenna system testbed. The $4\times1$ uniform linear away antenna was designed to operate at 1.885 to 2.2GHz with a total bandwidth of 315MHz. The array elements were based on the novel broadband L-probe fed inverted hybrid E-H (LIEH) shaped microstrip patch, which offers 22% size reduction to the conventional rectangular microstrip patch antenna. For steering the antenna beam, a commercial variable attenuator (KAT1D04SA002), a variable phase shifter (KPH350SC00) with four units each, and the corporate 4-ways Wilkinson power divider which was fabricated in-house were integrated to form the beamforming feed network. The developed antenna has an impedance bandwidth of 17.32% $(VSWR\leq1.5)$, 21.78% $(VSWR\leq2)$ with respect to center frequency 2.02GHz and with an achievable gain of 11.9dBi. The design antenna offer a broadband, compact and mobile solution for a 3G smart antenna testbed to fully characterized the IMT-2000 radio specifications and system performances.

• Journal of radiological science and technology
• /
• v.15 no.2
• /
• pp.17-23
• /
• 1992

Simple chest radiography is the most frequently performed examination in radiologic practice. However, with transmitted dose through chest which has the problem of wide variations in absorption, conventional Film/Screen Combinations Method make it difficult to delineate lung field mediastinum & cardia portion and subdiaphragmatic structures. In order to overcome this problem, we have been tried several methods as follows. High Kilovoltage Technique, Rare Earth Screen/Wide Lattitude Film, Use of Compensating Filter and Digital Beam Attenuator and recently Insigh System has been developed. In this paper, we'd like to discuss Insight film through apperciation by measuring the difference of contrast. In order to evaluate insight film. We have done experiments using Insight System with Simple Phase, Picker 550. We could get an result which was able to overcome the limitted dynamic range of conventional Film/Screen System remarkably.

• Korean Journal of Optics and Photonics
• /
• v.13 no.3
• /
• pp.235-239
• /
• 2002

A novel ultra-narrow linewidth DFB laser in the extended FBG ring cavity having kHz linewidth is presented. The method of linewidth compression was realized by introducing an extended fiber ring cavity into the cavity between the external FBG and the Bragg grating inside a DFB laser diode. Optimum optical feedback control was achieved by using an optical circulator and a variable optical attenuator to prevent mode hopping induced by spatial hole burning. To prove the validity of the proposed scheme, a self-heterodyne measurement set-up with fiber delay line of 63 km was utilized for the ultra-narrow linewidth measurement. A 3 dB linewidth of less than 3 kHz was demonstrated, which is resolution limited performance. This linewidth is equivalent to 3 dB linewidth of 2$\times$10$^{-8}$ nm.

• Journal of the Korea Society of Computer and Information
• /
• v.7 no.4
• /
• pp.115-120
• /
• 2002

This paper presents the implementation of IS-95 CDMA signal processor, baseband and Intermediate Frequency(IF) digital converter using Field Programmable Gate Array(FPGA) and ADC/DAC and frequency up/down converter IS-95 CDMA channel processor is generated the pilot channel signal with short PN code and Walsh-code generator. The digital If is composed of FPGA. digital transmit/receive signal processor and high speed analog-to-digital converter(ADC) and digital-to-analog converter(DAC). The frequency up/down converter consisted of filter, mixer, digital attenuator and PLL is analog conversion between intermediate frequency(IF) and baseband. This implemented system can be deployed in the IS-95 CDMA base station device etc.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.9
• /
• pp.974-978
• /
• 2003

The down-converter of the WCDMA Digital Optic Repeater is developed. Based on the system specifications, the structure of the down-converter is accomplished and its block diagram is drawn. The down-converter is implemented according to these block diagrams. Subsequently a low pass filter, an automatic level controlled attenuator, a frequency synthesizer and other components for the down-converter are designed and implemented, and a main board to integrate these modules is also manufactured. To reduce the noise floor of system and suppress the RF spurious noise, a PCB layout is performed carefully. For each module consisting of the down-converter and the entire system, the performance tests are accomplished to check the performance about the specifications.