• The Journal of Korean Academy of Prosthodontics
• /
• v.44 no.2
• /
• pp.229-242
• /
• 2006

Statement of problem: In order to increase preload with reducing the friction coefficient, abutment screws coated with pure gold and Teflon as dry lubricant coatings have been introduced. But the reported data indicate that if screw repeated tightening and loosening cycle, an efficiency of increasing preload was decreased by screw surface wearing off. Purpose: This study was to evaluate the influence of tungsten carbide/carbon coating, which has superior hardness and frictional wear resistance, on the preload of abutment screws and the stability of coating surface after repeated closures. Material and method: The rotational values of abutment screws and the compressive forces between abutment and fixture were measured in implant systems with three different joint connections, one external butt joint and two internal cones. Moreover the stability and the alteration of coating surface were examined by comparison of the compressive force and the removable torque values during 10 consecutive trials, observation with scanning electron microscope and analyzed the elemental composition with energy dispersive x-ray spectroscopy Results and conclusion: 1. Application of coating resulted in significant increase of compressive force in all implant systems(P<.05). The increasing rate of compressive force by coating in external butt joint was gloater than those in internal cones (P<.05). 2. Coated screw showed the significant additional rotation compared to non-coated screw in all implant systems (P<.05). There were no significant differences in the increasing rate of rotation among implant systems (P>.05). 3. Removable torque values were greater with non-coated screw than that with coated screw (P<.05). 4. Coated screw showed insignificant variations in the compressive forces during 10 consecutive trials(P>.05) 5. After repeated trials, the surface layer of coated screw was maintained relatively well. However surface wearing and irregular titanium fragments were found in non-coated screw.

• Proceedings of the KAIS Fall Conference
• /
• 2000.10a
• /
• pp.30-33
• /
• 2000

최근 국내에서도 관 동맥 질환 환자의 수가 급증하고 있으며, 관 동맥 질환의 치료 방법인 관 동맥 성형 술은 관 동맥 stent의 도입에 의하여 보편화되어 국내에서 년간 5000개 이상의 stent가 시술되고 있다. 그러나 stent는 고가(1,200천원/개)로 전량 수입에 의존하고 있으며, 시술 후 사망까지 이를 수 있는 혈전에 의한 급성 페쇠와 재 협착이 문제점이다. 이를 위한 한가지 방법이 생체 적합성이 뛰어난 복합 stent의 개발인데 SiC나 Carbon을 coating한 stent는 시술 후 혈전 형성을 억제하는 것으로 알려져 있다. 특히 가장 순수한 Pyrolytic carbon은 hemocompatibility가 탁월하고 기밀 성이기 때문에 본 연구에서 그의 CVB-Kinetics를 연구코저 하는 것이다. methane으로부터 pyrolytic carbon의 CVD는 온도에 따라서 다양한 구조를 가지며 따라서 그의 mechanism도 다양하다는 것은 잘 알려져 있다. 더구나 광간(균질)반응과 표면(불균질)반응의 정량적 관계에 따라서도 다르다는 것도 확인되었다. 그러나 stainless steel 316L로 만든 stent는 12 - 15 %의 Ni과 2%의 Mo을 함유해서 금속성을 잃지 않는 저온(600℃)에서도 pyrolytic carbon의 속매적 CVD가 가능함을 그리고 SiC의 코팅에 적합한 buffer layer 역할을 함을 확인하였다. 그리하여 본 연구는 반응기 설계에 필요한 저온 촉매적 pyrolytic carbon의 CVD-kinetics의 연구결로 그의 mechanism과 함께 rate law 식을 유도, 확인하였으며 600℃, 90kPa에서 P/sub ch4//P/sub H2/=5:1과 체류시간 1.8 sec가 최적임을 발견하였다. 이때 석출속도 11.2 g-mol/g-cat.h 혹은 두께속도로 73 nm/sec를 나타내었다.메타놀-물 (1 : 1) 유출액에서 $(0.80\;{\mu}g)$ 검출되었다. 하면 morey eel내장에서 얻은 독물질도 DEAE-셀루로즈에서 ST-1 과 ST-2로 나누어지며, 이 ST-1의 TLC, HPLC 및 알루미나 컬럼상의 거동이 파랑비늘돔에서 얻은 ST-1의 그것과 같으므로 scaritoxin으로 보고한 ST-1은 ciguatoxin의 형태인 less polar cigutoxin (LPCTX) 으로 생각된다.에서 각각 대조구의 57, 413 및 315% 증진되었다. 거품의 열안정성은 15분 whipping시, pH 4.0(대조구, 30.2%) 및 5.0(대조구, 23.7%)에서 각각 $0{\sim}38.0$ 및 $0{\sim}57.0%$이었고 pH 7.0(대조구, 39.6%) 및 8.0(대조구, 43.6%)에서 각각 $0{\sim}59.4$ 및 $36.6{\sim}58.4%$이었으며 sodium alginate 첨가시가 가장 양호하였다. 전체적으로 보아 거품안정성이 높은 것은 열안정성도 높은 경향이며, 표면장력이 낮으면 거품형성능이 높아지고, 비점도가 높으면 거품안정성 및 열안정성이 높아지는 경향이 있었다.protocol.eractions between application agents that are developed using different languages. Dynamic agent invocation is accomplished by Java Native Interface(JNI) that links two heterogeneous methods, and by KQML language interface that facilitates the communications between heterogeneous agents. This scheme of dyna

• Journal of KIISE:Information Networking
• /
• v.30 no.1
• /
• pp.75-81
• /
• 2003

User authentication, including confidentiality, integrity over untrusted networks, is an important part of security for systems that allow remote access. Using human-memorable Password for remote user authentication is not easy due to the low entropy of the password, which constrained by the memory of the user. This paper presents a new password authentication and key agreement protocol suitable for authenticating users and exchanging keys over an insecure channel. The new protocol resists the dictionary attack and offers perfect forward secrecy, which means that revealing the password to an attacher does not help him obtain the session keys of past sessions against future compromises. Additionally user passwords are stored in a form that is not plaintext-equivalent to the password itself, so an attacker who captures the password database cannot use it directly to compromise security and gain immediate access to the server. It does not have to resort to a PKI or trusted third party such as a key server or arbitrator So no keys and certificates stored on the users computer. Further desirable properties are to minimize setup time by keeping the number of flows and the computation time. This is very useful in application which secure password authentication is required such as home banking through web, SSL, SET, IPSEC, telnet, ftp, and user mobile situation.

• Restorative Dentistry and Endodontics
• /
• v.28 no.5
• /
• pp.378-384
• /
• 2003

This study evaluated the influence of a desensitizer(MS coat) on microtensile bond strength of different adhesives:a three-step adhesive(All-Bond 2), a two-step adhesive(Single Bond), a one-step adhesive(One-up Bond F). Non-caries extracted human molars were used. Dentin surface was obtained by horizontal section on mid-portion of crown using a water-cooled low speed diamond saw. Teeth were randomly divided into 6 group. AMO(MS coat + All Bond), SMO(MS coat + Single Bond)- and OMO(MS coat + One-up Bond F)-dentin surface were treated with 17% EDTA before bonded adhesive. AMX-, SMX- and OMX-dentin surface were bonded with All-Bond 2, Single Bond and One-up Bond F, respectively. with no previous treatment with MS coat and 17% EDTA. About 1cm high resin composite($Z-250^{TM}$) were incrementally build-up on the treated surface. The specimens for the microtensile test were serially sectioned perpendicular to the adhesive layer to obtain $0.7{\times}0.7mm$ sticks. 30 sticks were prepared from each group. After that. tensile bond strength for each stick was measured with Microtensile Tester at a 1mm/min crosshead speed. Fractured dentin surfaces were observed under the SEM. The results were statistically analysed by using a One-way ANOVA and Tukey's test(p<0.05). Value in MPa were: $AMO-44.35{\pm}13.21;{\;}SMO-39.35{\pm}13.32;{\;}OMO-31.07{\pm}10.25;{\;}AMX-49.22{\pm}16.38;{\;}SMX-56.02{\pm}13.35;{\;}OMX-72.93{\pm}16.19$. Application of MS coat reduced microtensile bond strengths of both Single Bond and One-up Bond F, whereas microtensile bond strengths of All-Bond 2 were not affected significantly.

• Journal of Conservation Science
• /
• v.28 no.4
• /
• pp.403-410
• /
• 2012

The brine treatment applied during the fabrication of forged high tin bronze objects is considered effective at the removal of surface oxide layers developed at elevated temperatures. There is not much information, however, available for the understanding of its exact effect and purpose. This work performed laboratory experiments to characterize the effect brine treatments produce on the surface of bronze objects during fabrication. Specimens were first made in the bronze shop of the Yongin folk village under varying conditions of brine treatments, and the results obtained were then used in the following laboratory experiments where the effect of brine treatments were investigated in terms of brine concentrations, alloy compositions and thermo-mechanical treatments. The results show that oxide layers generated at high temperature are easily removed by the brine treatment. It was found that the element, chlorine, played a key role in the removal of such oxide layers as opposed to the other constituent of the brine, sodium, makes no notable contribution. In bronze alloys containing 22% tin, this brine effect is obtained regardless of the application of forging as long as the brine concentration is over 0.5% based on weight. In alloys containing lead, however, no brine effect is observed due to the molten lead that emerges from inside the hot bronze specimen and forms a thin layer on its surface.

• The Journal of Engineering Geology
• /
• v.12 no.4
• /
• pp.471-484
• /
• 2002

Alluviums in the Keum River watershed cover an areal extent of $3,029{\;}\textrm{km}^2$ and contain about 8.1 billion tons of groundwater. However, the waters are severely polluted by nitrate, possibly due to the application of nitrogen fertilizer (>250 N kg/ha) on agricultural land. This paper aims to elucidate the pollution status and behaviors of nitrate in alluvial groundwaters in the Keum River watershed area, based on regional hydrogeochemical study. Most of the collected samples (n = 186) are polluted by nitrate (average = 42.2 mg/L, maximum = 295 mg/L). About 29% of the samples have the nitrate concentrations exceeding Korean Drinking Water Standard (44 mg/L $NO_3$). The distribution of nitrate concentrations in the study area is largely dependant on geochemical environments of alluvial aquifers. In particular, the decrease of redox potential of alluvial groundwaters showed a good correlation with the decreases of nitrate, iron, and manganese concentrations. Thus, the change of redox state in alluvial aquifers, likely reflecting their sedimentary environments, controls both the behavior and fate of nitrogen compounds and their natural attenuation (denitrification) in aquifers. A carbon-rich, silty layer within alluvium strata forms a reducing condition and possesses a buffering capacity on nitrate pollution.

• Restorative Dentistry and Endodontics
• /
• v.35 no.2
• /
• pp.134-142
• /
• 2010

The purpose of this study was to evaluate the effect of Er,Cr:YSGG laser irradiation with hypersensitivity mode on microtensile bond strength of composite resin. Twenty extracted permanent molars were randomly assigned to six groups, according to the irradiation of Er,Cr:YSGG laser, adhesive system (Optibond FL or Clearfil SE bond) and application time of etchant (15 sec or 20 sec). Then composite resin was build up on each conditioned surface. The restored teeth were stored in distilled water at room temperature for 24 h and twelve specimens for each group were prepared. All specimens were subjected to microtensile bond strength and the fracture modes were evaluated. Also, the prepared dentin surface and laser irradiated dentin surface were examined under SEM. The results were as follows: 1. The microtensile bond strength of laser irradiated group was lower than that of no laser irradiated group. 2. Regardless of laser irradiation, the microtensile bond strength of Optibond FL was higher than that of Clearfil SE bond. And the microtensile bond strength of 20 sec etching group was higher than that of 15 sec etching group when using Optibond FL. 3. The SEM image of laser irradiated dentin surface showed prominent peritubular dentin, opened dentinal tubules and no smear layer.

• Korean Journal of Remote Sensing
• /
• v.31 no.6
• /
• pp.561-570
• /
• 2015

Till now, applications of many kinds of satellite images have been accentuated in the datacentric scientific studies, researches regarding system development and concerned technologies for them are on the un-matured stage. Especially, satellite image processing requires large volume data handling and specific analysis functionalities, so that practical necessity of base study for system development is emphasized on. In the view of information system, various edged trends such as web standards, cloud computing, or web framework are utilized owing to their application benefits proven and business needs. Considered these aspects, a testing implementation was carried out using OpenStack cloud computing environment and e-government framework. As for the processing functions, WPS in GeoServer, as one of OGC web standards, was applied to perform interoperable data processing scheme between two or more remote servers. Working with the server implemented, client-side was also developed using several open sources such as HTML 5, jQuery, and OpenLayers. If it is that completed further experiments onsite applications with actual multi-data sets and extension of on-demand functionalities with the result of this study, it will be referred as an example case model for complicated and complex system design and implementation which needs cloud computing, geo-spatial web standards and web framework.

• Polymer(Korea)
• /
• v.37 no.6
• /
• pp.694-701
• /
• 2013

A new copolymer named T-TI24T (poly((5,5-(2-butyl-5,6-bisdecyloxy-4,7-di-thiophen-2-yl-isoindole-1,3-dione))- alt-(2,5-thiophene))) based on phthalimide derivative and thiophene is synthesized by the Stille-coupling reaction. The polymer shows relatively high number average molecular weight of 86500 g/mol with good solubility in common organic solvents such as chloroform, 1,2-dichlorobenzene, and toluene and is thermally stable up to $380^{\circ}C$. Besides, it possesses a relatively low highest occupied molecular orbital (HOMO) energy level of -5.33 eV, promising the high open circuit voltage ($V_{oc}$) for photovoltaic applications. Active layer solution of polymer T-TI24T-as a donor and (6)-1-(3-(methoxycarbonyl)- {5}-1-phenyl[5,6]-fullerene (PCBM)-as an acceptor in different weight ratios is applied to fabricate the polymer solar cell devices. The ratio of polymer/PCBM affects the solar cell efficiency and the best performance exhibits in the device with polymer/PCBM = 1:3 (w/w), which shows a power conversion efficiency (PCE) of 0.199% and a $V_{oc}$ of 0.99 V, respectively. Even though the device shows the very low PCE, the $V_{oc}$ is higher than that of well known bulk heterojunction type solar cell based on P3HT:PC61BM (c.a. 0.5 V).

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.156-156
• /
• 2000

Recently, the surface electronic states have attracted much attention since their standing wave patterns created around steps, defects, and adsorbates on noble metal surfaces such as Au(111), Ag(110), and Cu(111) were observed by scanning tunneling microscopy (STM). As a typical example, a striking circular pattern of "Quantum corral" observed by Crommie, Lutz, and Eigler, covers a number of text books of quantum mechanics, demonstrating a wavy nature of electrons. After the discoveries, similar standing waves patterns have been observed on other metal and demiconductor surfaces and even on a side polane of nano-tubes. With an expectation that the surface states could be utilized as one of ideal cases for studying two dimensionakl (sD) electronic system, various properties, such as mean free path / life time of the electronic states, have been characterized based on an analysis of standing wave patterns, . for the 2D electron system, electron density is one of the most importnat parameters which determines the properties on it. One advantage of conventional 2D electron system, such as the ones realized at AlGaAs/GaAs and SiO2/Si interfaces, is their controllability of the electrondensity. It can be changed and controlled by a factor of orders through an application of voltage on the gate electrode. On the other hand, changing the leectron density of the surface-state 2D electron system is not simple. On ewqy to change the electron density of the surface-state 2D electron system is not simple. One way to change the electron density is to deposit other elements on the system. it has been known that Pd(111) surface has unoccupied surface states whose energy level is just above Fermi level. Recently, we found that by depositing Pd on Cu(111) surface, occupied surface states of Cu(111) is lifted up, crossing at Fermi level around 2ML, and approaches to the intrinsic Pd surface states with a increase in thickness. Electron density occupied in the states is thus gradually reduced by Pd deposition. Park et al. also observed a change in Fermi wave number of the surface states of Cu(111) by deposition of Xe layer on it, which suggests another possible way of changing electron density. In this talk, after a brief review of recent progress in a study of standing weaves by STM, I will discuss about how the electron density can be changed and controlled and feasibility of using the surface states for a study of 2D electron system. One of the most important advantage of the surface-state 2D electron system is that one can directly and easily access to the system with a high spatial resolution by STM/AFM.y STM/AFM.