• Korean Journal of Materials Research
• /
• v.2 no.6
• /
• pp.417-427
• /
• 1992

Silicon ion implantation was performed to LPCVD amorphous Si films and the low temperature annealing process followed with various conditions to find the optimal physical properties by studying recrystallization behavior. The uniformity of the recrystallized films was inspected by optical microscopy and for this purpose, new KOH: (IPA) : $H_2$O: $K_2$C${r_2}{O_7}$, etchant was developed. XRD and TEM results showed that the crystallites were grown as a form of dendrite with (111) preferred orientation, and the grain size was increased with dose concentration. The maximum grain size was obtained when the 3${\times}{10^{15}}$c$m^2$ implanted amorphous Si film was recrystallized at 55 $0^{\circ}C$for more than 40 hrs and at this condition the grain size was 3.2${\mu}$m.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.13 no.6
• /
• pp.297-303
• /
• 2003

Mn-Ni-Co type thin films were prepared at various conditions by a rf magnetron sputtering system. At the condition. or substrate temperature of $300^{\circ}C$ and $Ar/O_2$= 10/0, a cubic spinel phase was obtained. When oxygen was included in process gas, a cubic spinel phase was not formed even after the thermal annealing at $900^{\circ}C$. The thermistor thin film had no other elements except Mn, Ni and Co. The infrared reflection spectra of the thermistor thin films showed that the films had somewhat high reflectance for incoming infrared ray with some angle. The etch rate of the thermistor thin films was about 63nm/min at a condition of DI water : $HNO_3$: HCl = 60 : 30 : 10 vol%. The B constant and temperature coefficient of resistance of the thermistor thin films were 3500 K and -3.95 %/K, respectively. The voltage responsivity of the thermistor thin film infrared sensor was 108.5 V/W and its noise equivalent power and specific detectivity were $5.1\times 10^{-7}$ W/$Hz^{-1/2}$ and $0.2\times 10^6$cm $Hz^{1/2}$/W, respectively.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.9
• /
• pp.371-377
• /
• 2003

We perform the physical analysis such that Si/W composition ratios and phosphorus distribution change in the W/S $i_{x}$ thin films according to phosphorus concentration of polysilicon and W $F_{6}$ flow rate for the formation of WS $i_{x}$ polycide used as a gate electrode. We report that these physical characteristics have effects on the contact resistance between word line and bit line in DRAM devices. RBS measurements show that for the samples having phosphorus concentrations of 4.75 and 6.0${\times}$10$^{2-}$ atoms/㎤ in polysilicon, by applying W $F_{6}$ flow rates decreases from 4.5 to 3.5 sccm, Si/W composition ratio has increases to 2.05∼2.24 and 2.01∼2.19, respectively. SIMS analysis give that phosphorus concentration of polysilicon for both samples have decreases after annealing, but phosphorus concentration of WS $i_{x}$ thin film has increases by applying W $F_{6}$ flow rates decreases from 4.5 to 3.5 sccm. The contact resistance between word line and bit line in the sample with phosphorus concentration of 6.0 ${\times}$ 10$^{20}$ atoms/㎤ in polysilicon is lower than the sample with 4.75 ${\times}$ 10$^{20}$ atoms/㎤ After applying W $F_{6}$ flow rates decreases from 4.5 to 3.5 sccm, the contact resistance has been improved dramatically from 10.1 to 2.3 $\mu$ $\Omega$-$\textrm{cm}^2$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.160-160
• /
• 2010

In this work, we investigate ohmic contacts to p-type GaN using a Pt/Cu/Au metallization scheme in order to achieve low resistance and thermally stable ohmic contact on p-GaN. An ohmic contact formed by a metal electrode deposited on a highly doped InGaN/GaN superlattice sturucture on p-GaN layer. The specific contact resistance is $1.56{\times}10^{-6}{\Omega}cm^2$ for the as-deposited sample, $1.35{\times}10^{-4}{\Omega}cm^2$ for the sample annealed at $250^{\circ}C$ and $6.88{\times}10^{-3}{\Omega}cm^2$ for the sample annealed at $300^{\circ}C$.

• Biomedical Science Letters
• /
• v.2 no.2
• /
• pp.241-247
• /
• 1996

Poor yields of amplified DNAs could be resulted in polymerase chain reaction(PCR) processes with G+C-rich DNA primers because of their high $T_m$ values. To maximize the yields of amplification in PCR processes with G+C-rich primers, we compared the yields of amplified DNA fragments according to the concentrations of specific denaturants added to the reaction mixture of PCR system. With addition of the mixture of 2.5% glycerol and 1.25% formamide, or 2.5% dimethyl sulfoxide to the reaction cocktail, respectively, remarkable increases in the yields of amplified DNA fragments were not observed in the PCR systems with G+C-low primers of Lyl chromosomal gene from Borrelia burgdorferi but observed in the PCR system with G+C- ich primers of Is900 gene from Mycobacterium parahberculosis. Although we were not practically able to discriminate the yields of PCR DNAs according to the concentrations used in this study, addition of the mixture of 5% glycerol and 2.5% formamide, or 5% DMSO tended to increase the production of extra bands.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.6
• /
• pp.581-588
• /
• 2013

This paper presents a study of the process temperature dependence of $Al_2O_3$ film grown by thermal atomic layer deposition (ALD) as a passivation layer in the crystalline Si (c-Si) solar cells. The deposition rate of $Al_2O_3$ film maintained almost the same until $250^{\circ}C$, but decreased from $300^{\circ}C$. $Al_2O_3$ film deposited at $250^{\circ}C$ was found to have the highest negative fixed oxide charge density ($Q_f$) due to its O-rich condition and low hydroxyl group (-OH) density. After post-metallization annealing (PMA), $Al_2O_3$ film deposited at $250^{\circ}C$ had the lowest slow and fast interface trap density. Actually, $Al_2O_3$ film deposited at $250^{\circ}C$ showed the best passivation effects, that is, the highest excess carrier lifetime (${\tau}_{PCD}$) and lowest surface recombination velocity ($S_{eff}$) than other conditions. Therefore, $Al_2O_3$ film deposited at $250^{\circ}C$ exhibited excellent chemical and field-effect passivation properties for p-type c-Si solar cells.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.10
• /
• pp.29-38
• /
• 1998

In this paper, we have induced a model for the growth and dissolution of oxygen precipitates which is generated during arbitrary thermal treatments or VLSI processes in CZ-grown silicon. Based on diffusion-limited growth law and detailed balance equilibrium theory, growth and dissolution rates are induced and inserted into a set of chemical rate equations and a Fokker-Planck equation. Then this is solved by numerical analysis. And because phenomenon at the silicon surface must be considered differently in various annealing conditions, in particular in $O_2$ ambient we have considered the growth model of SiO$_2$ at the surface of silicon wafer and the enhancement of oxygen solubility. By this method, oxygen depth profile and density distribution of oxygen precipitates are calculated more accurately than the other simulation results.

• Journal of Sensor Science and Technology
• /
• v.12 no.6
• /
• pp.265-272
• /
• 2003

This paper describes anodic bonding characteristics of MLCA (Multi Layer Ceramic Actuator) to Si-wafer using evaporated Pyrex #7740 glass thin-films for MEMS applications. Pyrex #7740 glass thin-films with same properties were deposited on MLCA under optimum RF magneto conditions(Ar 100%, input power $1\;W/cm^2$). After annealing in $450^{\circ}C$ for 1 hr, the anodic bonding of MLCA and Si-wafer was successfully performed at 600 V, $400^{\circ}C$ in - 760 mmHg. Then, the MLCA/Si bonded interface and fabricated Si diaphragm deflection characteristics were analyzed through the actuation test. It is possible to control with accurate deflection of Si diaphragm according to its geometries and its maximum non-linearity is 0.05-0.08 %FS. Moreover, any damages or separation of MLCA/Si bonded interfaces do not occur during actuation test. Therefore, it is expected that anodic bonding technology of MLCA/Si wafers could be usefully applied for the fabrication process of high-performance piezoelectric MEMS devices.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.182-182
• /
• 1999

The chemisorption effect of CO on the Ni/Cu(001) surface was investigated using LEED(Low Energy Electron Diffraction) and EELS(Electron Energy Loss Spectrscopy0 under the UHV conditions. after mounting the Cu(001) single crystal in the UHV chamber (base pressure 1$\times$10-10Torr), a clean surface was obtained after a few cycles of repeated Ar+ ion sputtering and annealing at about 40$0^{\circ}C$. The epitaxial thin Ni films were formed on the Cu(001) by evaporation from 99.999% Ni block. The pseudomorphic growth and the orderness of the thin Ni films were monitored by c(2$^{\circ}C$2) LEED pattern. CO adlayers on Ni epitaxial thin films were prepared by dosing pure CO has through a leak valve. After CO adsorpton at room temperature, two pairs of peaks were observed by EELS, whose relative intensities are changed as the film thickness is varied and time is elapsed. These two pair of peaks are likely related to different bonding sites (-top and bridge sites) of C-Ni as well as C-O vibration. Experimental results and qualitative interpretation of the spectra wille be discussed. The possibility of using EELS in combination with probe species (CO) to investigate the nature of thin film growth is mentioned. We will report the experimental result of O2 dosage on Ni film and interaction of CO and O2.

• Journal of the Korean Ceramic Society
• /
• v.42 no.2 s.273
• /
• pp.123-126
• /
• 2005

Barium Titanate (BT) powders were synthesized by solvothermal method with an ethanol as a solvent. The average particle size was increased with the feedstock concentration: the size was 59 nm at $6.25{\times}10^{-2}$ M and 89 nm at 0.5 M. The sample obtained at 0.5 M concentration was analysed by Rietveld refinement and the mole fraction of tetragonal phase was $75.5\%$ and lattice parameter of tetragonal phase was a=0.3999 (nm), c=0.4032 (nm), and cubic phase was a=0.4015 (nm). TEM analysis for the samples with condition of annealing at $500^{\circ}C$ for I h showed that hydroxyl ions on oxygen sites were not found for these experimental conditions.