• Korean Journal of Materials Research
• /
• v.9 no.2
• /
• pp.168-172
• /
• 1999

We have studied the formation of Co/Ti bilayer silicide with low resistivity and good thermal stability on the heavily boron doped $\textrm{p}^{+}$-Si region. In this paper, Co/Ti bilayer silicides were fabricated by depositing Co($150\AA$)/Ti($50\AA$) films on the clean $\textrm{p}^{+}$-Si substrates in an E-beam evaporator and performing the two step RTA process (first annealing: 650$50^{\circ}C$/20sec, second annealing: $800^{\circ}C$/20sec) in a $N_2$ambient with the pressure of $\textrm{10}^{-1}$atm. Co/Ti bilayer silicides obtained from our experiments exhibited the low resistivity of about $18\mu\Omega$-cm and the uniform thickness of about $500\AA$ without change of sheet resistance and agglomeration under the long post0annealing time up to $1000^{\circ}C$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.197-200
• /
• 2001

In this letter, we report on the investigation of Ni/Si/Ni Ohmic contacts to n-type 4H-SiC. Ohmic contacts have been formed by a vacuum annealing and $N_2$ gas ambient annealing method at $950^{\circ}C$ for 10 min. The specific contact resistivity ( $\rho_{c}$ ), sheet resistance($R_s$), contact resistance($R_c$), transfer length($L_T$) were calculated from resistance($R_T$) versus contact spacing(d) measurements obtained from 10 TLM(transmission line method) structures. The resulting average values of vacuum annealing sample were $\rho_{c}=3.8{\times}10^{-5}\Omega cm^{3}$, $R_{c}=4.9{\Omega}$, $R_{T}=9.8{\Omega}$ and $L_{T}=15.5{\mu}m$, resulting average values of another sample were $\rho_{c}=2.29{\times}10^{-4}\Omega cm^{3}$, $R_{c}=12.9{\Omega}$ and $R_{T}=25.8{\Omega}$. The physical properties of contacts were examined using X-Ray Diffraction and Auger analysis, there was a uniform intermixing of the Si and Ni, migration of Ni into the SiC.

• Journal of the Korean Vacuum Society
• /
• v.9 no.4
• /
• pp.341-345
• /
• 2000

We investigated the microstructures and the electrical properties of $ZrO_2$thin films deposited by reactive DC magnetron sputtering on (100) Si with different deposition conditions and annealing treatments. The refractive index of the $ZrO_2$ thin films increased with annealing temperatures and deposition powers, and approached to the ideal value of 2.0~2.2. The $ZrO_2$thin films deposited at the room temperature are amorphous, and the films are polycrystalline at the deposition temperature of $300^{\circ}C$. Both the thickness of the interfacial oxide layer and the root-mean-square (RMS) value of surface roughness increased upon annealing in the oxygen ambient. The Cmax value and leakage current value decreased with the increase of thickness of the interfacial oxide thickness.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.29.1-29.1
• /
• 2009

Fabrication of good quality P-type GaN remained as a challenge for many years which hindered the III-V nitrides from yielding visible light emitting devices. Firstly Amano et al succeeded in obtaining P-type GaN films using Mg doping and post Low Energy Electron Beam Irradiation (LEEBI) treatment. However only few region of the P-GaN was activated by LEEBI treatment. Later Nakamura et al succeeded in producing good quality P-GaN by thermal annealing method in which the as deposited P-GaN samples were annealed in N2 ambient at temperatures above $600^{\circ}C$. The carrier concentration of N type and P-type GaN differs by one order which have a major effect in AlGaN based deep UV-LED fabrication. So increasing the P-type GaN concentration becomes necessary. In this study we have proposed a novel method of activating P-type GaN by electrochemical potentiostatic method. Hydrogen bond in the Mg-H complexes of the P-type GaN is removed by electrochemical reaction using KOH solution as an electrolyte solution. Full structure LED sample grown by MOCVD serves as anode and platinum electrode serves as cathode. Experiments are performed by varying KOH concentration, process time and applied voltage. Secondary Ion Mass Spectroscopy (SIMS) analysis is performed to determine the hydrogen concentration in the P-GaN sample activated by annealing and electrochemical method. Results suggest that the hydrogen concentration is lesser in P-GaN sample activated by electrochemical method than conventional annealing method. The output power of the LED is also enhanced for full structure samples with electrochemical activated P-GaN. Thus we propose an efficient method for P-GaN activation by electrochemical reaction. 30% improvement in light output is obtained by electrochemical activation method.

• Journal of the Korean Vacuum Society
• /
• v.20 no.2
• /
• pp.127-134
• /
• 2011

We investigate the crystallographic orientation and strain states of the Ni/Ag ohmic contacts on p-type GaN. The Ag film in the Ni/Ag contact was severely agglomerated during high temperature annealing in air ambient. As a results, after annealing for 24 h, the Ni/Ag contact shows non-linear I-V curve and low light reflectance of ~21% at 460 nm wavelength. High-resolution X-ray diffraction results show that the interplanar spacing of Ag (111) planes is almost same to that of bilk Ag after annealing for 24 hrs, indicating that the in-plane tensile strain in the Ag film was fully relaxed due to the Ag agglomeration.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.197-200
• /
• 2001

In this letter, we report on the investigation of Ni/Si/Ni Ohmic contacts to n-type 4H-SiC. Ohmic contacts have been formed by a vacuum annealing and N$_2$ gas ambient annealing method at 950$^{\circ}C$ for 10 min. The specific contact resistivity($\rho$$\sub$c/), sheet resistance(R$\sub$S/), contact resistance(R$\sub$S/), transfer length(LT) were calculated from resistance(R$\sub$T/) versus contact spacing(d) measurements obtained from 10 TLM(transmission line method) structures. The resulting average values of vacuum annealing sample were $\rho$$\sub$c/=3.8x10$\^$-5/ Ω$\textrm{cm}^2$ , R$\sub$c/=4.9Ω, R$\sub$T/=9.8Ω and L$\sub$T/=15.5$\mu\textrm{m}$, resulting average values of another sample were $\rho$$\sub$c/=2.29x10$\^$-4/ Ω$\textrm{cm}^2$ , R$\sub$c/=12.9Ω, R$\sub$T/=25.8Ω. The Physical properties of contacts were examined using X-Ray Diffraction and Auger analysis, there was a uniform intermixing of the Si and Ni, migration of Ni into the SiC.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.167-171
• /
• 2003

We report the material and electrical properties of $CoSi_2$ and $NiSi_2$contacts to n-type 4H-SiC depending on the post-annealing and the metal covering conditions. The Ni and Co silicides are deposited by RF sputtering with Ni/Si/Ni and Co/Si/Co films separately deposited on 4H-SiC substrates. The deposited films are annealed at $800\;^{\circ}C$ in $Ar:H_2$ (9:1) gas ambient. Results of the specific surface resistivity measurements show that the resistivity of the Co-based metal contact was the one order lower than that of the Ni-based contact. The specific contact resistance was measured by a transmission line technique, and the specific contact resistivity of $1.5{\times}10^{-6}\;{\Omega}\;cm^2$ is obtained for Co/Si/Co metal structures after a two-step annealing; at $550\;^{\circ}C$ for 10 min and $800\;^{\circ}C$ for 3min. The physical properties of the contacts were examined by using XRD and AES, and the results indicate that the Co-based metal contacts have better structural stability of silicide phases formed after the high temperature annealing.

• Korean Journal of Materials Research
• /
• v.24 no.9
• /
• pp.443-450
• /
• 2014

Amorphous (a-Si) films were epitaxially crystallized on a very thin large-grained poly-Si seed layer by a silicide-enhanced rapid thermal annealing (SERTA) process. The poly-Si seed layer contained a small amount of nickel silicide which can enhance crystallization of the upper layer of the a-Si film at lower temperature. A 5-nm thick poly-Si seed layer was then prepared by the crystallization of an a-Si film using the vapor-induced crystallization process in a $NiCl_2$ environment. After removing surface oxide on the seed layer, a 45-nm thick a-Si film was deposited on the poly-Si seed layer by hot-wire chemical vapor deposition at $200^{\circ}C$. The epitaxial crystallization of the top a-Si layer was performed by the rapid thermal annealing (RTA) process at $730^{\circ}C$ for 5 min in Ar as an ambient atmosphere. Considering the needle-like grains as well as the crystallization temperature of the top layer as produced by the SERTA process, it was thought that the top a-Si layer was epitaxially crystallized with the help of $NiSi_2$ precipitates that originated from the poly-Si seed layer. The crystallinity of the SERTA processed poly-Si thin films was better than the other crystallization process, due to the high-temperature RTA process. The Ni concentration in the poly-Si film fabricated by the SERTA process was reduced to $1{\times}10^{18}cm^{-3}$. The maximum field-effect mobility and substrate swing of the p-channel poly-Si thin-film transistors (TFTs) using the poly-Si film prepared by the SERTA process were $85cm^2/V{\cdot}s$ and 1.23 V/decade at $V_{ds}=-3V$, respectively. The off current was little increased under reverse bias from $1.0{\times}10^{-11}$ A. Our results showed that the SERTA process is a promising technology for high quality poly-Si film, which enables the fabrication of high mobility TFTs. In addition, it is expected that poly-Si TFTs with low leakage current can be fabricated with more precise experiments.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.327-327
• /
• 2009

ZnO with a large band gap (~3.37 eV) and exciton binding energy (~60 meV), is suitable for optoelectronic applications such as ultraviolet (UV) light emitting diodes (LEDs) and detectors. However, the ZnO-based p-n homojunction is not readily available because it is difficult to fabricate reproducible p-type ZnO with high hall concentration and mobility. In order to solve this problem, there have been numerous attempts to develop p-n heterojunction LEDs with ZnO as the n-type layer. The n-ZnO/p-GaN heterostructure is a good candidate for ZnO-based heterojunction LEDs because of their similar physical properties and the reproducible availability of p-type GaN. Especially, the reduced lattice mismatch (~1.8 %) and similar crystal structure result in the advantage of acquiring high performance LED devices. In particular, a number of ZnO films show UV band-edge emission with visible deep-level emission, which is originated from point defects such as oxygen vacancy, oxygen interstitial, zinc interstitial[1]. Thus, defect-related peak positions can be controlled by variation of growth or annealing conditions. In this work, the undoped ZnO film was grown on the p-GaN:Mg film using RF magnetron sputtering method. The undoped ZnO/p-GaN:Mg heterojunctions were annealed in a horizontal tube furnace. The annealing process was performed at $800^{\circ}C$ during 30 to 90 min in air ambient to observe the variation of the defect states in the ZnO film. Photoluminescence measurements were performed in order to confirm the deep-level position of the ZnO film. As a result, the deep-level emission showed orange-red color in the as-deposited film, while the defect-related peak positions of annealed films were shifted to greenish side as increasing annealing time. Furthermore, the electrical resistivity of the ZnO film was decreased after annealing process. The I-V characteristic of the LEDs showed nonlinear and rectifying behavior. The room-temperature electroluminescence (EL) was observed under forward bias. The EL showed a weak white and strong yellowish emission colors (~575 nm) in the undoped ZnO/p-GaN:Mg heterojunctions before and after annealing process, respectively.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.2
• /
• pp.9-14
• /
• 2009

The effects of post-annealing temperature on the optical and electrical properties of P-doped ZnO thin films grown on sapphire substrate have been investigated under oxygen ambient. The XRD shows that regardless of the post-annealing temperature, all P-doped ZnO thin films indicate the c-axis orientation. The results of hall effect measurements indicate the P-doped ZnO thin film annealed at $850^{\circ}C$ exhibits p-type behavior with hole concentration of $1.18{\times}1016cm^{-3}$ and hole mobility of $0.96cm^2/Vs$. The low-temperature (10K) Photoluminescence results reveal that the peak related to the neutral-acceptor exciton (A0X), free electrons to neutral acceptor (FA) and donor acceptor pair (DAP) at 3.351ev, 3.283eV and 3.201eV are observed in the films showing p-type behavior with acceptor. The optimization of deposition and post-annealing conditions will certainly make the P-doped ZnO thin films promising materials for the application to the next generation of optical devices.