• 한국정보통신학회논문지
• /
• 제7권3호
• /
• pp.468-473
• /
• 2003

본 연구에서는 박막트랜지스터의 특성 향상을 위하여 강유전성 박막을 게이트 절연층으로 사용하기 위하여 강유전성 박막과 a-Si:H의 계면특성을 조사하였다. 먼저 강유전성 박막 중에 대표적인 SrTiO$_3$를 I-BEAM 증착기로 박막을 형성시켰다. 형성된 박막은 N2 분위기에서 $150^{\circ}C∼600^{\circ}C$로 1시간 ANNEALING하여 전자현미경으로 표면을 측정하였다. SrTiO$_3$의 유전상수는 50∼100 정도였으며 항복전계는 1∼l.5 MV/cm로 매우 우수한 유전특성을 갖고 있었다. 강유전체 박막 위에 a-SiN:H,a-Si:H(n-type a-Si:H) 등을 PECVD로 증착하여 MFNS구조를 형성하였다. 계면특성을 C-V PLOTTER로 측정한 결과 SrTiO$_3$ 박막은 SiN과의 접합이 매우 안정되어 있었고 C-V특성은 SiN/a-Si:H과 유사하였다. 그러나 FERROELECTRIC/a-S:H의 경우가 훨씬 CAPACITANCE 값이 컸으며, 이는 강유전체 박막의 높은 유전상수에 기인 된 것이라 생각된다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.624-627
• /
• 2003

The BLT thin-films were one of the promising ferroelectric materials with a good leakage current and degradation behavior on Pt electrode. The BLT target was sintered at $1100^{\circ}C$ for 4 hours at the air ambient. $Bi_{3.25}La_{0.75}Ti_3O_{12}$ (BLT) thin-film deposited on $Pt/Ti/SIO_2/Si$ wafer by rf magnetron sputtering method. At annealed $700^{\circ}C$, (117) and (006) peaks appeared the high intensity. The hysteresis loop of the BLT thin films showed that the remanent polarization ($2Pr=Pr^+-Pr^-$) was $16uC/cm^2$ and leakage current density was $1.8{\times}10^{-9}A/cm^2$ at 50 kV/cm with coersive electric field when BLT thin-films were annealed at $700^{\circ}C$. Also, the thin film showed fatigue property at least up to $10^{10}$ switching bipolar pulse cycles under 7 V. Therefore, we induce access to optimum fabrication condition of memory device application by rf-magnetron sputtering method in this report.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.231-231
• /
• 2010

Thermoelectric properties of a multi-layered thin film, which was composed with indium selenide and bismuth telluride, were investigated. The structure of the layered thin film is Bi-Te /In-Se/Bi-Te and it was prepared on sapphire substrate by RF magnetron sputter using stoichiometric $Bi_2Te_3$ (99.9%) and $In_2Se_3$(99.99%) target at room temperature. Then, it was annealed at temperature range of 150 - $500^{\circ}C$ in Ar ambient. Structural characterizations were done using X-ray diffraction(XRD, BRUKER, D8, 60kW) and transmission electron microscopy (TEM, FEI, Tecnai, F30 S-Twin), respectively. Cross-section of multi-layer structure was observed by Scanning electron microscopy (SEM). The resistivity and Seebeck coefficient of these samples were also measured by conventional equipment at room temperature. The maximum value of power factor was $1.16\;{\mu}W/k^2m$ at annealing temperature of $400^{\circ}C$.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.388-388
• /
• 2010

In this study, Ferroelectric vinylidene fluoride-trifluoroethylene (VF2-TrFE) copolymer films were directly deposited on degenerated Si (n+, $0.002\;{\Omega}{\cdot}cm$) using by spin coating method. A 1~5 wt% diluted solution of purified vinylidene fluoride-trifluoroethylene (VF2:TrFE = 70:30) in a dimethylformamide (DMF) solvent were prepared and deposited on silicon wafers at a spin rate of 2000 ~ 4000 rpm for 2 ~ 30 seconds. After annealing in a vacuum ambient at 100 ~ $200^{\circ}C$ for 60 min, upper aluminum electrodes were deposited by vacuum evaporation for electrical measurement. X-ray diffraction results showed that the VF2-TrFE films on Si substrates had $\beta$-phase of copolymer structures. The capacitance on highly doped Si wafer showed hysteresis behavior like a butterfly shape and this result indicates clearly that the copolymer films have ferroelectric properties. The typical measured remnant polarization ($P_r$) and coercive filed ($E_c$) values were about $5.7\;{\mu}C/cm^2$ and 710 kV/em, respectively, in an applied electric field of ${\pm}$ 1.5 MV/em. The gate leakage current densities measured at room temperature was less than $7{\times}10^{-7}\; A/cm^2$ under a field of 1 MV/cm.

• 전자공학회논문지D
• /
• 제35D권10호
• /
• pp.29-38
• /
• 1998

본 논문에서는 CZ 방법으로 성장된 실리콘에서 임의의 열처리 과정 또는 VLSI 공정중에 발생하는 산소석출물(oxygen precipitates)의 성장 및 감소에 대한 모델을 유도하고 수치해석법으로 시뮬레이션을 수행하여 모델에 대한 타당성을 검증하였다. 확산제한 성장법칙(diffusion-limited growth law)과 DBET(detailed balance equilibrium theory)를 이용하여 산소 석출물의 성장률과 감소율을 유도하고 이를 CREs(chemical rate equations)와 PFE (Fokker-Planck equation)이 결합된 식에 적용하여 수치해석법으로 풀었다. 또한 어닐링 분위기에 따라 표면에서 일어나는 현상을 달리 고려해야 하는데, 특히 O₂가스 분위기에서는 산화막이 성장되는 조건을 고려해야 하므로 산화막 성장 모델과 산소 용해도 증가등의 영향을 고려하였다. 이 방법으로 기존의 결과보다 더 정확하게 깊이에 따른 산소 농도의 분포와 산소 석출물의 밀도분포 함수를 계산할 수 있었다.

• 한국진공학회지
• /
• 제19권1호
• /
• pp.58-65
• /
• 2010

먼저 RF 마그네트론 스퍼터링법을 이용하여 사파이어 기판 위에 AlN 박막을 증착하였다. AlN 공급원으로는 분말소결된 AlN 타겟을 적용하였다. 플라즈마 파워를 50에서 110 W로 증가시켰을 때 AlN 층의 두께는 선형적으로 증가하였다. 그러나 동작압력을 3에서 10 mTorr로 증가시켰을 때는 동작기체인 아르곤 양이 증가함에 따라 AlN 타겟으로부터 스퍼터링되어 나온 AlN 입자들의 평균자유행정의 거리가 감소하기 때문에 AlN 층의 두께는 약간 감소하였다. 질소 기체를 아르곤과 섞어주었을 때는 질소의 낮은 스퍼터링 효율에 의해서 AlN의 두께는 크게 감소하였다. 다음으로는 ZnO 형판 위에 AlN를 증착하였다. 그러나 700도 이상의 열처리에 의해서 AlN와 ZnO의 계면이 약간 분리되어 계면의 열적 안정성이 낮다는 결과를 얻었다. 게다가 스퍼터링으로 증착한 AlN 박막의 나쁜 결정성으로 인하여 700도에서 MOCVD의 반응기 기체인 수소와 암모니아에 의해서 AlN 밑의 ZnO 층이 분해되는 현상도 관찰하였다. 그리고 900도 이상에서는 ZnO가 완전히 분해되어 AlN 박막이 완전히 분리되었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.458.2-458.2
• /
• 2014

We have demonstrated that simple brush-painted Ti-doped $In_2O_3$(TIO) films can be used as a cost effective transparent anodes for organic solar cells (OSCs). We examined the RTA effects on the electrical, optical, and structural properties of the brush painted TIO electrodes. By the direct brushing of TIO nanoparticle ink and rapid thermal annealing (RTA), we can simply obtain TIO electrodes with a low sheet resistance of 28.25 Ohm/square and a high optical transmittance of 85.48% under atmospheric ambient conditions. Furthermore, improvements in the connectivity of the TIO nano-particles in the top region during the RTA process play an important role in reducing the resistivity of the brush-painted TIO anode. In particular, the brush painted TIO films showed a much higher mobility ($33.4cm^2/V-s$) than that of previously reported solution-process transparent oxide films ($1{\sim}5cm^2/V-s$) due to the effects of the Ti dopant with higher Lewis acid strength (3.06) and the reduced contact resistance of TIO nanoparticles. The OSCs fabricated on the brush-painted TIO films exhibited cell-performance with an open circuit voltage (Voc) of 0.61 V, shot circuit current (Jsc) of $7.90mA/cm^2$, fill factor (FF) of 61%, and power conversion efficiency (PCE) of 2.94%. This indicates that brush-painted TIO film is a promising cost-effective transparent electrode for printing-based OSCs with its simple process and high performance.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제48권4호
• /
• pp.221-225
• /
• 1999

This paper shows the parameters to affect the critical characteristic of YBaCuO superconducting bulk fabricated by MPMG (Melt Powdered Melt Growth)process. In order to investigate proper processing variables, the effect of the holding time at the melting temperature and that of the slow cooling time in $O_2\; ambient\; on\; the\; J_c$ were experimented. And then with the above obtained heat treatment conditions, the effects of addition of $Y_2BaCuO_5\; and\; Ag\; on\; the\; J_c$ were also investigated. A proper slow cooling time yields phase transformation from Tetragonal $(YBa_2Cu_3O_6)$ to Orthorhombic $(YBa_2Cu_3O_7)$ during an annealing time in $O_2$. Ag addition plays a role in increasing the $T_c\; and\; the J_c$, but the magnetization decreases. The $J_c$ and the magnetization increase with addition of Y211. $J_c$ of the sample added Ag 10wt% is superiorover 3000 G. Proper holding time, slow cooling time and amount of impurity addition are important parameters in fabricating the YBaCuO bulk by MPMG process with high $J_c$.

• 한국전기전자재료학회논문지
• /
• 제18권2호
• /
• pp.125-129
• /
• 2005

Two kinds of physical treatments were examined for the analysis both of intrinsic surface and interior nature of CuInS $e_2$[CIS] and CuGaS $e_2$[CGS] films grown in separated systems. For the first method, a selenium protection layer which was immediately deposited after the growth of the CIS was investigated. The Se cap layer protects CISe surface from oxidation and contamination during the transport under ambient atmosphere. The Se cap was removed by thermal annealing at temperature above 15$0^{\circ}C$. After the decapping treatment at 2$25^{\circ}C$ for 60 min, ultraviolet photoemission and inverse photoemission measurements of the CIS film showed that its valence band maximum(VBM) and conduction band minimum (CBM) are located at 0.58 eV below and 0.52 eV above the Fermi level $E_{F}$, respectively. For the second treatment, an Ar ion beam etching was exploited. The etching with ion kinetic energy $E_{k}$ above 500 eV resulted in broadening of photoemission spectra of core signals and occasional development of metallic feature around $E_{F}$. These degradations were successfully suppressed by decreasing $E_{k}$ below 400 eV. CGS films etched with the beam of $E_{k}$ = 400 eV showed a band gap of 1.7 eV where $E_{F}$ was almost centered.st centered.

• Applied Science and Convergence Technology
• /
• 제25권1호
• /
• pp.19-24
• /
• 2016

In this study, we evaluated the change of electronic structure during redox process in cerium-doped $ZrO_2$ grown by sol gel method. By sol-gel method, we could obtain cerium-doped $ZrO_2$ in high oxygen partial pressure and low temperature. After post annealing process in nitrogen ambient, the film is deoxidized. We used spectroscopic and theoretical methods to analysis change of electronic structure. X-ray absorption spectroscopy (XAS) for O K1-edge and Density Functional Theory (DFT) calculation using VASP code were performed to verify the electronic structure of the film. Also, high resolution x-ray photoelectron spectroscopy (HRXPS) for Ce 3d was carried out to confirm chemical bond of cerium doped $ZrO_2$. Through the investigation of the electronic structure, we verified as followings. (1) During reduction process, binding energy of oxygen is increase. Simultaneously, oxidation state of cerium was change to 4+ to 3+. (2) Cerium 4+ and cerium 3+ states were generated at different energy level. (3) Absorption states in O K edge were mainly originated by Ce 4+ $f_0$ and Ce 3+, while occupied states in valance band were mainly originated from Ce 4+ $f_2$.