• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.3
• /
• pp.281-287
• /
• 2001

For the conventional two-dimensional source location of acoustic emission (AE) based on the threshold crossing, wave velocity has to be measured in the actual structure to calculate the arrival-time difference and thus to form the two hyperbolae. Velocity is dependent on the fiber orientation, however, due to the dependence of elastic modulus on fiber orientation in anisotropic materials such as compost#e plates. This tan affect the accuracy of AE source location and make the source location procedure complicated. In this study, we propose a method to reduce the location error in anisotropic plates by using the numerical solution of nonlinear equations, where the velocity term has been removed by employing the fourth sensor. The efficiency and validity of the proposed method has also been experimentally verified.

• Tunnel and Underground Space
• /
• v.11 no.1
• /
• pp.72-78
• /
• 2001

A method to determine elastic constants for transversely isotropic rock using a single uniaxial compression test was proposed by Kim(1995). However, some problems were found when this method was applied. We derived two different equations in determination of elastic constants using V$\sub$12/ and V$\sub$21/ and performed uniaxial compression tests for two specimens whose angles between transversely isotropic plane and horizontal plane are 30$^{\circ}C$ and 65$^{\circ}C$. The anisotropic elastic constants should be calculated with different equations depend on the angle. If the anisotropic angle is lower than 45$^{\circ}$, V$\sub$21/ may be used. However, if the anisotropic angle is higher than 45$^{\circ}$, V$\sub$12/ may be used.

• Journal of Korean Society of Steel Construction
• /
• v.12 no.3 s.46
• /
• pp.303-315
• /
• 2000

The main object of this study is to analyze mechanical behaviors as anisotropic three-dimensional body under various static loads. This paper presents the applicability of the finite difference method to three dimensional problem of anisotropic body. The finite difference method as applied here is generalized to anisotropic three-dimensional problem of elastic body where the governing differential equations of equilibrium of such bodies are expressed in terms of the displacement u, v, and w in the coordinates axes x, y and z, care being taken to modify the finite difference expressions to satisfy the appropriate boundary conditions. By adopting a new three dimensional finite difference modelling including elimination of pivotal difference points in the case of free boundary condition, the three dimensional problem of anisotropic body was successfully completed. Several numerical results show quick convergence and numerical validity of finite difference technique in three dimensional problem.

• Ecology and Resilient Infrastructure
• /
• v.4 no.1
• /
• pp.54-62
• /
• 2017

This study investigated compound open channel flow using OpenFOAM Large Eddy Simulation (LES). Large eddy simulations were carried out by solving the filtered continuity and momentum equations numerically. One equation LES and non-uniform grid were applied to capture the anisotropic turbulence and secondary flow near the wall. The results of large eddy simulations of turbulent flow in a compound open channel with deep and shallow flood plain depths are presented. These LESs are validated with experimental data, resulting in a good agreement between measured and calculated data. The role of anisotropic turbulence in generating secondary currents is illustrated.

• Korean Journal of Optics and Photonics
• /
• v.15 no.3
• /
• pp.200-213
• /
• 2004

The realization of partially coherent Gaussian Schell-model beams with isotropic cross section and anisotropic degree of coherence function is investigated theoretically. An optical system is devised to transform diffused light generated by passing the Gaussian beam of the He-Ne laser thorough a rotating holographic diffuser to the partially coherent Gaussian Schell-model beam with isotropic cross section and anisotropic degree of coherence function. Analytic design equations are formulated and design examples are presented.

• Coupled systems mechanics
• /
• v.6 no.3
• /
• pp.317-333
• /
• 2017

The present paper is concerned with the investigation of Rayleigh waves in a homogeneous transversely isotropic magnetothermoelastic medium with two temperature, in the presence of Hall current and rotation. The formulation is applied to the thermoelasticity theories developed by Green-Naghdi theories of Type-II and Type-III. Secular equations are derived mathematically at the stress free and thermally insulated boundaries. The values of Determinant of secular equations, phase velocity and Attenuation coefficient with respect to wave number are computed numerically. Cobalt material has been chosen for transversely isotropic medium and magnesium material is chosen for isotropic solid. The effects of rotation, magnetic field and phase velocity on the resulting quantities and on particular case of isotropic solid are depicted graphically. Some special cases are also deduced from the present investigation.

• 연구논문집
• /
• s.24
• /
• pp.81-96
• /
• 1994

To investigate failure mechanisms observed in carbon-phenolic thermal insulators, differential equations which govern the decomposition process in a deformable anisotropic porous solid are derived for three-dimensional axisymmetric constructions. The governing equations not only couple the material deformation with pore pressure, but also couple pressure and temperature, which means that heat convected by the pyrolysis gases is properly accounted for. Then the Bubnov-Galerkin finite element method is applied to these equations to transform them into a semidescrete finite element system. A thermal insulation liner in the cowl region under typical operating conditions is analyzed to find a mechanism for plylift. The results from the structural analysis show across-ply failure in the cowl zone. The mechanism for plylift is hypothesized as a sequential procedure : 1) the across-ply failure which is the precursor to plylift and 2) the local fiber buckling caused by generation of excessive in-plane compressive stress. To prevent plylift, the across-ply stress can be reduced by using appropriate material ply angles in cowl zone design.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• v.5 no.1
• /
• pp.55-78
• /
• 2001

Given the anisotropic Poisson equation $-{\nabla}{\cdot}{\mathcal{K}}{\nabla}p=f$, one can convert it into a system of two first order PDEs: the Darcy law for the flux $u=-{\mathcal{K}{\nabla}p$ and conservation of mass ${\nabla}{\cdot}u=f$. A very natural mixed finite volume method for this system is to seek the pressure in the nonconforming P1 space and the Darcy velocity in the lowest order Raviart-Thomas space. The equations for these variables are obtained by integrating the two first order systems over the triangular volumes. In this paper we show that such a method is really a standard finite element method with local recovery of the flux in disguise. As a consequence, we compare two approaches in analyzing finite volume methods (FVM) and shed light on the proper way of analyzing non co-volume type of FVM. Numerical results for Dirichlet and Neumann problems are included.

• Journal of the Korean Society for Advanced Composite Structures
• /
• v.3 no.4
• /
• pp.17-26
• /
• 2012

This study presents a governing equations of bending behavior of anisotropic sandwich plates with multi-layered laminated composite faces. Based on zig-zag models for through thickness deformations, the shear deformation of composite faces is included. All edges of plate are assumed to be simply supported. Results of the bending analysis under lateral loads are presented for the influence of various lay up sequences of antisymmetric angle-ply laminated faces. The accuracy of the approach is ascertained by comparing solutions from the sandwich plates theory with composite faces to the laminated plates theory. Since the present analysis considers the bending stiffness of the core and also the transverse shear deformations of the laminated faces, the proposed method showed higher than that calculated according to the general laminated plates theory. The information presented might be useful to design sandwich plates structure with polymer matrix composite faces.

• Transactions of Materials Processing
• /
• v.4 no.3
• /
• pp.222-232
• /
• 1995

The planar anisotripic FEM analysis for predicting earing profiles and draw-in amounts in the deep-drawing process is introduced. An implicit, incremental, updated Lagrangian formulation with a rigid-viscoplastic constitutive equation is employed. Contact and friction are considered through the mesh-based unit vector and normal contact pressure. The consistent full set of governing relations, which is comprising euilbrium and geometric constraint equations, is appropriately linearized. Barlat's strain-rate potential is employed, whose in-plane anisotropic properties are taken into account with anisotropic coefficients and potential parameters. The linear triangular membrane elements are used for depicting the formed sheet. In the numerical simulations of deep drawing processes of a flat-top cylindrical cup for 2090-T3 aluminum alloy sheet show good agreement with experiments, although some discrepancies were observed in the directional trend of cup height and thickness strains.