• Journal of Soil and Groundwater Environment
• /
• v.11 no.6
• /
• pp.61-68
• /
• 2006

Soil washing techniques coupled with high pressure air jet were applied for diesel-contaminated soils sampled by an underground oil reservoir of which the initial total petroleum hydrocarbon (TPH) ($2,828{\pm}206\;mg/kg$) exceeded 5 times of current standard level (500 mg/kg) regulated by the Soil-Environment Conservation Law. Through several tests, we found that the position of impeller has a critical impact for washing efficiencies. The highest washing efficiency was obtained at an oblique angle (30 degree) for the impeller and optimized mixing speed (300 rpm) that could have high shearing forces. Considered economical and feasible aspects, the optimum mixing time was 10 min. Rate constants of TPH removal derived from the first-order equation were not linearly increased as mixing speed increased, indicating that mechanical mixing has some limits to enhance the washing efficiencies. Application of high-pressure air jet in washing process increased the washing efficiency. This increase might be caused by the fact that the surface of micro-air bubbles strongly attached hydrophobic matters of soil particles. As the pressure of air jet increased, the separation efficiencies of TPH-contaminated soil particles increased. In the combined process of high-pressure air jet and mixing by impeller, the optimum mixing speed and air flow-rate were determined to be 60 rpm and $2\;kg/cm^2$, respectively. Consequently, the washing technique coupled with high-pressure air jet could be considered as a feasible application for remediating petroleum-contaminated soils.

• Solar Energy
• /
• v.12 no.3
• /
• pp.70-83
• /
• 1992

The interaction between the surface radiation and the mixed convection transport from an isolated thermal source, with a uniform surface heat flux input and located in a rectangular enclosure, is stuied numerically. The enclosure simulates a practical system such an air cooled electric device, where an air-stream flows through the openings on the two vertical walls. The heat source represents an electric component located in such an enclosure. The size of this cavity is $0.1[m]{\times}0.1[m]$. The inlet velocity is assumed as 0.07[m/s] and the inlet temperature is maintained as $27^{\circ}C$. The inflow is kept at a fixed position. Laminar, two dimensional flow is assumed, and the problem lies in the mixed convection regime, governed by buoyancy force and surface readiation. The significant variables include the location of the out-flow opening, of the heat source and the wall emissivity. The basic nature of the resulting interaction betwwn the externally induced air stream and the buoyancy-driven flow generated by the source is investigated. As a result, the best location of the heat source to make the active heat transfer is 0.075[m] from the left wall on the floor. The trends observed are also discussed in terms of heat removal from practical systems such as electric circuitry.

• The Journal of Korean Academy of Prosthodontics
• /
• v.59 no.2
• /
• pp.201-209
• /
• 2021

In removable partial dentures, many types of retentive systems have been studied and applied in clinical treatment. One of those systems is the double crown denture system which is widely used in European countries such as Germany and Sweden. Telescopic double crown dentures have several advantages such as convenience in maintaining oral hygiene, enabling to transfer occlusal force along the long axis of the abutment, and secondary splinting effect between the abutments which leads to higher clinical performance compared to conventional removal partial dentures. In this clinical case, the patient was initially restored with a maxillary hybrid telescopic double crown denture with friction pin using remaining natural teeth as abutments. After 7 years, due to lack of recall check-up and poor oral hygiene, the abutment teeth were affected by periodontitis and 4 out of 5 of the abutment teeth had to be extracted. 3 additional implants were placed and the original abutment tooth with the inner crown was maintained. The mandible had fixed prostheses including implants but nevertheless, with strategic implant placement, the patient adapted well and was satisfied with the new maxillary tooth-implant combined double crown denture.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.8
• /
• pp.5541-5549
• /
• 2015

This paper introduces a safer and more power efficient heater by using induction heating, to apply to the semiconductor wafer fabrication exhaust gas cleaning system. The exhaust gas cleaning system is currently made with filament heater that generates an endothermic reaction of N2 gas for the removal of moisture. Induction theory, through the bases of theoretical optimization and electronic implementation, is applied in the design of the induction heater specifically for the semiconductor wafer exhaust system. The new induction heating design provides a solution to the issues with the current energy inefficient, unreliable, and unsafe design. A robust and calibrated design of the induction heater is used to optimize the energy consumption. Optimization is based on the calibrated ZVS induction circuit design specified by the resonant frequency of the exhaust pipe. The fail-safe energy limiter embedded in the system uses a voltage regulator through the feedback of the MOSFET control, which allows the system performance to operate within the specification of the N2 Heater unit. A specification and performance comparison from current conventional filament heater is made with the calibrated induction heater design for numerical analysis and the proof of a better design.

• The Korean Journal of Air & Space Law and Policy
• /
• v.35 no.2
• /
• pp.75-111
• /
• 2020

The civilian drone world has evolved in recent years from one dominated by hobbyists to growing involvement by companies seeking to profit from unmanned flight in everything from infrastructure inspections to drone deliveries that are already subject to regulations. Drone flight under the property right relation with the land owner would be deemed legal on the condition that expeditious and innocent passage of drone flight over the land be assured. The United Nations Convention on the Law of the Sea (UNCLOS) enshrines the concept of innocent passage through a coastal state's territorial sea. Passage is innocent so long as it is not prejudicial to the peace, good order or security of the coastal state. A vessel in innocent passage may traverse the coastal state's territorial sea continuously and expeditiously, not stopping or anchoring except in force majeure situations. However, the disturbances caused by drone flight may be removed, which is defined as infringement against the constitutional interest of personal rights. For example, aggressive infringement against privacy and personal freedom may be committed by drone more easily than ever before, and than other means. The cost-benefit analysis, however, has been recognjzed as effective criteria regarding the removal of disturbances or injunction decision. Applying that analysis, the civil action against such infringement may not find suitable basis for making a good case. Because the removal of such infringement through civil actions may result in only the deletion of journal article. The injunction of drone flight before taking the information would not be obtainable through civil action, Therefore, more detailed and meticulous regulation and criteria in public law domain may be preferable than civil action, at present time. It may be suitable for legal stability and drone industry to set up the detailed public regulations restricting the free flight of drone capable of acquiring visual information amounting to the infrigement against the right of personal information security.

• The korean journal of orthodontics
• /
• v.27 no.4 s.63
• /
• pp.585-597
• /
• 1997

The purpose of this study was to evaluate the effect of estrogen on the periodontium and alveolar bone tissue response during experimental tooth movement in ovariectomized rats. Eighty female rats, 250gm in body weight, were classified into four groups ; sham operated group(NN), ovariectomized group(ON), ovariectomized & estrogen injected group(OE), sham operated & estrogen injected group(NE). flats were ovariectomized before 3 weeks to begin the experiment, which resulted in estrogen-deficient osteoporosis. In OE group & NE group, estrogen was injected $50{\mu}g/kg\;B.W.$ every other days. The left maxillary 1st molar was moved mesially with 60g force. Each foot rats were sacrificed after 1, 3, 7, 15 days from application of orthodontic appliance and alter additional 7 days from removal of orthodontic appliance. Histological findings on mesial roots of upper 1st molar in pressure and tension side are observed. The results were summarized as follows ; 1. In pressure side of alveolar bone, the number of osteoclasts and Howship's lacuna of ON group was significantly more than that of NN group from 1 day to 15 days(P<0.05). Especially the number of Howship's lacuna of ON group was significantly more than that of OE group during all experimental period(P<0.05). 2. In tension side of alveolar tune, the number of osteoclasts of ON group was significantly increased from 1 day to 3 days and decreased after 7 days. But the number of osteoclast of ON group was significantly mote than that of NN group during all experimental period(P<0.05). Also the number of Howship's lacuna of all groups was abruptly increased at 1 day, but slowly decreased till experimental 15 days. And the number of Howship's lacuna of of group was significantly more than that of NN group from 0 hr to 7 days(P<0.05). 3. The speed of tooth movement of OE group & NE group was similar to that of NN group(P>0.05). The amount of tooth movement of ON group between 7 days and 15 days was significantly greater than those of other groups(P<0.05). 4. The degree of relapse of ON group after 7 days from removal of orthodontic appliance was similar to those of other groups(P>0.05).

• Journal of the korean academy of Pediatric Dentistry
• /
• v.30 no.4
• /
• pp.545-553
• /
• 2003

To achieve good dentin bonding, we must obtain proper wet dentin surface. The purpose of this study was to compare dentin surface according to different wetness degree by AFM image as studying how to obtaining proper wet dentin surface. Intact recently extracted primary teeth were used in the study. The extracted teeth were stored in distilled water at $4^{\circ}C$ until prepared. The teeth were used to prepare 1mm thick dentin disks with exposed surfaces parallel to the occlusal surfaces. The surface of the dentin were polished with polishing disk. The sample were ultrasonically cleaned with distilled water. The sample of each group were treated by different ways. We compared dentin surface of each group by AFM image. From the experiment, the following results were obtained. 1. Acid etching in the dentin surface of primary teeth, resulted in the removal of the smear layer, which opened dentinal tubules, caused the demineralization of peritubular and intertubular dentin, and exposed a collagen-rich transition zone. 2. If the etched dentin was so dehydrated, the intertubular dentin surfaces deceased in height and the diameters of the dentinal tubules decreased slightly. 3. In the group dried with compressed air for 20 seconds at 2 cm, the dentin surfaces were too excessive dried and dehydrated. 4. In the group dried with compressed air for 3 seconds at 2 cm, dry cotton, wet cotton, microbrush and absorbent tissue paper, the dentin surfaces were properly wet.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.64 no.2
• /
• pp.152-158
• /
• 2019

This study was conducted to develop and prove the effects of an agronomical pest control measure on ginseng cultivated by direct seeding in paddy field, and the results obtained are as follows. Decomposition of ginseng in field during overwintering was due to gray mold rot caused by Botrytis cinerea, which occurred in October or November of 2016 and intensified in February and March the following year. The occurrence rate of gray mold rot based on shading materials was 6.5%, 16.8%, and 29.5% with light-proof paper, PE shade net, and rice straw shade, respectively. The initial infection occurred in the leaves prior to wintering and secondary infection occurred in the stems after wintering. The rate of screrotium formation by gray mold in the above-ground parts of ginseng tended to increase: 26.6% on October 20, 33.7% in November 20, and 41.8% on December 20. The force needed to remove the leaves and stems from withered ginseng was 0.2, 0.94, 2.5, and 5 kg for 1-, 2-, 3-, and 4- and 5-year holds; the force required was 1 kg after wintering, making it relatively easy to remove. The disease incidence rate after the removal of leaves and stems was 2.5%, 1.2%, and 2.2% in 4-, 5-, and 6-year-old plants, respectively, and a disease high incidence rate of 8.8%, 13.0%, and 18.2%, respectively, was seen when the leaves and stems were not removed. In both transplanting and direct seeding, the miss-planted rate decreased and the germination rate increased when shading material was removed and the surface of ridge was covered with soil or vinyl.

• The korean journal of orthodontics
• /
• v.31 no.5 s.88
• /
• pp.517-523
• /
• 2001

Titanium miniscrews we being used increasingly as an anchorage for tooth movement, because they ate easy to place and to remove, increase the number of sites available, give minimum strain to patients regarding surgical procedures, and offer uneventful healing alter removal. The use of titanium miniscrews as an orthodontic anchorage has been reported in clinical case reports, but clinicians have experienced screw loosening when using such screws.' To our knowledge, there are no published reports evaluating the stability of miniscrews. Information about the length of miniscrews used in relation to the location is of some importance, as stability will vary depending on bone duality The purpose of this study was to evaluate a variety of Lengths of miniscrews (dimeter: 2mm) which were inserted in maxilla or mandible and to demonstrate in a dog model which miniscrew provides fundamental stability in the jaws. 10 mm long miniscrews in the maxilla and 8mm long: miniscrews in the mandible showed no clinical mobility and retained their position throughout an 8 weeks force (200g) application. The mucosal condition around the screws was healthy in cases in which miniserews were inserted in the alveolar bone between the roots and the head of the screws emerged into the attached gingiva. When the force application was terminated, radiographic analysis revealed neither rent resorption not periodontal pathology around the miniscrews that remained stable during the entire treatment period. This study suggests that if titanium miniscrews with adequate length are properly used depending on the location, they provide sufficient stability for orthodontic anchorage.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 1993.06a
• /
• pp.1051-1054
• /
• 1993

The International Atomic Energy Agency's Statute in Article III.A.5 allows it“to establish and administer safeguards designed to ensure that special fissionable and other materials, services, equipment, facilities and information made available by the Agency or at its request or under its supervision or control are not used in such a way as to further any military purpose; and to apply safeguards, at the request of the parties, to any bilateral or multilateral arrangement, or at the request of a State, to any of that State's activities in the field of atomic energy”. Safeguards are essentially a technical means of verifying the fulfilment of political obligations undertaken by States and given a legal force in international agreements relating to the peaceful uses of nuclear energy. The main political objectives are: to assure the international community that States are complying with their non-proliferation and other peaceful undertakings; and to deter (a) the diversion of afeguarded nuclear materials to the production of nuclear explosives or for military purposes and (b) the misuse of safeguarded facilities with the aim of producing unsafeguarded nuclear material. It is clear that no international safeguards system can physically prevent diversion. The IAEA safeguards system is basically a verification measure designed to provide assurance in those cases in which diversion has not occurred. Verification is accomplished by two basic means: material accountancy and containment and surveillance measures. Nuclear material accountancy is the fundamental IAEA safeguards mechanism, while containment and surveillance serve as important complementary measures. Material accountancy refers to a collection of measurements and other determinations which enable the State and the Agency to maintain a current picture of the location and movement of nuclear material into and out of material balance areas, i. e. areas where all material entering or leaving is measurab e. A containment measure is one that is designed by taking advantage of structural characteristics, such as containers, tanks or pipes, etc. To establish the physical integrity of an area or item by preventing the undetected movement of nuclear material or equipment. Such measures involve the application of tamper-indicating or surveillance devices. Surveillance refers to both human and instrumental observation aimed at indicating the movement of nuclear material. The verification process consists of three over-lapping elements: (a) Provision by the State of information such as - design information describing nuclear installations; - accounting reports listing nuclear material inventories, receipts and shipments; - documents amplifying and clarifying reports, as applicable; - notification of international transfers of nuclear material. (b) Collection by the IAEA of information through inspection activities such as - verification of design information - examination of records and repo ts - measurement of nuclear material - examination of containment and surveillance measures - follow-up activities in case of unusual findings. (c) Evaluation of the information provided by the State and of that collected by inspectors to determine the completeness, accuracy and validity of the information provided by the State and to resolve any anomalies and discrepancies. To design an effective verification system, one must identify possible ways and means by which nuclear material could be diverted from peaceful uses, including means to conceal such diversions. These theoretical ways and means, which have become known as diversion strategies, are used as one of the basic inputs for the development of safeguards procedures, equipment and instrumentation. For analysis of implementation strategy purposes, it is assumed that non-compliance cannot be excluded a priori and that consequently there is a low but non-zero probability that a diversion could be attempted in all safeguards ituations. An important element of diversion strategies is the identification of various possible diversion paths; the amount, type and location of nuclear material involved, the physical route and conversion of the material that may take place, rate of removal and concealment methods, as appropriate. With regard to the physical route and conversion of nuclear material the following main categories may be considered: - unreported removal of nuclear material from an installation or during transit - unreported introduction of nuclear material into an installation - unreported transfer of nuclear material from one material balance area to another - unreported production of nuclear material, e. g. enrichment of uranium or production of plutonium - undeclared uses of the material within the installation. With respect to the amount of nuclear material that might be diverted in a given time (the diversion rate), the continuum between the following two limiting cases is cons dered: - one significant quantity or more in a short time, often known as abrupt diversion; and - one significant quantity or more per year, for example, by accumulation of smaller amounts each time to add up to a significant quantity over a period of one year, often called protracted diversion. Concealment methods may include: - restriction of access of inspectors - falsification of records, reports and other material balance areas - replacement of nuclear material, e. g. use of dummy objects - falsification of measurements or of their evaluation - interference with IAEA installed equipment.As a result of diversion and its concealment or other actions, anomalies will occur. All reasonable diversion routes, scenarios/strategies and concealment methods have to be taken into account in designing safeguards implementation strategies so as to provide sufficient opportunities for the IAEA to observe such anomalies. The safeguards approach for each facility will make a different use of these procedures, equipment and instrumentation according to the various diversion strategies which could be applicable to that facility and according to the detection and inspection goals which are applied. Postulated pathways sets of scenarios comprise those elements of diversion strategies which might be carried out at a facility or across a State's fuel cycle with declared or undeclared activities. All such factors, however, contain a degree of fuzziness that need a human judgment to make the ultimate conclusion that all material is being used for peaceful purposes. Safeguards has been traditionally based on verification of declared material and facilities using material accountancy as a fundamental measure. The strength of material accountancy is based on the fact that it allows to detect any diversion independent of the diversion route taken. Material accountancy detects a diversion after it actually happened and thus is powerless to physically prevent it and can only deter by the risk of early detection any contemplation by State authorities to carry out a diversion. Recently the IAEA has been faced with new challenges. To deal with these, various measures are being reconsidered to strengthen the safeguards system such as enhanced assessment of the completeness of the State's initial declaration of nuclear material and installations under its jurisdiction enhanced monitoring and analysis of open information and analysis of open information that may indicate inconsistencies with the State's safeguards obligations. Precise information vital for such enhanced assessments and analyses is normally not available or, if available, difficult and expensive collection of information would be necessary. Above all, realistic appraisal of truth needs sound human judgment.