• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.3
• /
• pp.473-478
• /
• 1987

In this paper the optimum values of natural frequency ratio and damping ratio for damped systems were studied by numerical analysis. The relation between the amplitude ratio and frequency ratio obtained for the non-linear dynamic vibration absorber was found and it was compared with that of linear system. The results shows that the optimum frequency ratio decreases and the optimum damping ratio increases when the mass ratio of the damped system increases. The resonance frequency ratio and amplitude ratio decrease as mass ratio increases for the non-linear spring system.

• Journal of Korean Association for Spatial Structures
• /
• v.4 no.1 s.11
• /
• pp.61-68
• /
• 2004

The wind tracker and structural monitoring system recorded wind and dynamic response data. The measured building is located in the moutatin in Sokcho. The damping ratio and natural frequency were analysed in this paper to obtain amplitude dependence. Amplitude dependent damping was showed clearly in the increasing rate of 9%. The tendency of dynamic properties of building obtained here are useful for the validation of dynamic properties of buildings in the evaluation of serviceability.

• ETRI Journal
• /
• v.37 no.5
• /
• pp.922-928
• /
• 2015

A novel peak-to-average power ratio (PAPR) reduction method is proposed for single-carrier frequency-division multiple access (SC-FDMA) signals. The proposed method deliberately distorts the amplitude values of a few of the complex modulated symbols that cause peaks beyond a predetermined threshold in the samples of the output signal. The method then marks the location indices of the distorted symbols by using a pilot block at the transmitter without transmitting side information. At the receiver, the method is then able to recover the distorted amplitude values through the marked location indices. Computer simulation results show that when compared to conventional SC-FDMA signals, the proposed scheme can effectively reduce the PAPR of SC-FDMA signals with asymptotically consistent bit error rate (BER) performance.

• ETRI Journal
• /
• v.29 no.2
• /
• pp.231-233
• /
• 2007

One of the drawbacks in an OFDM system is the high peak-to-average power ratio (PAPR). Among a number of techniques to reduce the high PAPR, simple amplitude predistortion (SAP), a form of active constellation extension, has been proposed to effectively achieve the desired PAPR. In this letter, a novel scheme, simple amplitude and phase predistortion (SAPP), is proposed. In SAP the carriers' amplitude is utilized to combat the peak signal. Each amplitude is amplified according to its degree of contribution as a metric. In addition to amplitude, SAPP also utilizes the phase. Simulation results indicate that the proposed scheme provides better PAPR reduction than SAP.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.1
• /
• pp.124-130
• /
• 2018

The EMG amplitude estimator, which has been investigated as an indicator of muscle force, is of high relevance not only in biomechanical studies but also more and more in clinical applications. This paper presents a new approach to estimate surface EMG amplitude by using the mean spike and mean turn amplitude(MSA and MTA) variables. Surface EMG signals, a total of 198 signals, were recorded from biceps brachii muscle over the range of 20-80%MVC isometric contraction and performance of the MSA and MTA variables applied to amplitude estimation of the EMG signals were investigated. To examine the performance, a SNR(signal-to-noise ratio) was computed from each amplitude estimate. The results of the study indicate that MSA and MTA amplitude estimations with first order whitening filter and 300[ms]-350[ms] moving average window length are optimal and show better performance(mean SNR improvement of 6%-15%) than the most frequently used variables(ARV and RMS).

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.26 no.4
• /
• pp.158-162
• /
• 2014

A series of numerical simulation has been carried out to study thermo-hydraulic characteristics of a primary surface type heat exchanger, which is designed for the evaporator and condenser of a geothermal ORC. Working fluid is geothermal water at hot side and R-245fa, which is a refrigerant designed for ORC, at cold side. Amplitude ratio of the channel and Reynolds number are considered as design parameters. Nusselt number is presented for the Reynolds number ranging from 50 to 150 and compared to analytic solutions. The result shows that higher amplitude ratio channel gives better heat transfer performance within the range of investigation.

• Wind and Structures
• /
• v.38 no.1
• /
• pp.59-74
• /
• 2024

Large Eddy Simulation (LES) is used to explore the influence of vibration frequency and amplitude on the aerodynamic performance of a rectangular cylinder with an aspect ratio of B/D=5 (B: breadth; D: depth of cylinder) at a Reynolds number of 22,000 near resonance frequency. In smooth flow conditions, the research employs a sequence of three-dimensional simulations under forced vibration with diverse frequency ratios f_e / f_o = 0.8-1.2 (f_e : oscillation frequency; f_o : Strouhal frequency when the rectangular cylinder is stationary ) and oscillation amplitudes A_h/D = 0.05 - 0.3. The individual influences of f_e / f_o and A_h/D on the characteristics of integrated and distributed aerodynamic forces are the focal points of discussion. For the integrated aerodynamic force, particular emphasis is placed on the analysis of the dependence of velocity-proportional component C₁ and displacement-proportional component C₂ of unsteady aerodynamic force on amplitude and frequency ratio. Near the resonance frequency, the dependencies of C₁ and C₂ on amplitude are stronger than that of frequency ratio. For the distributed aerodynamic force, the increase in frequency and amplitude promotes the position of the main vortex core and reattachment to the leading edge in the streamwise direction. In the spanwise direction, vibration enhances the spanwise correlation of aerodynamic force to weaken the three-dimensional effect of the flow field, and a lower frequency ratio and larger amplitude amplify this effect.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.32 no.4
• /
• pp.421-431
• /
• 1996

From comparing the impact dynamic absorber with the impact damper in the auxiliary vibration system with the conventional dynamic absorber, the following conclusions are obtained as follows ; 1. Recognizing that the amplitude restraining effect of the impact dynamic absorber become resonable in a comparison of conventional one development of an improved dynamic absorber may be probable. 2. With increasing the frequency ratio, the 1st resonance peak is higher but the 2nd one gets lower. In addition, the frequency ratio is peak located at the same resonance. 3. The optimum impact clearance is smaller and the vibration constraining effect becomes better with and increase in the mass of impact ball. And it is recognizable that the optimum tuning frequency ratio and impact clearance in an accordance with the mass ratio are varied. 4. The optimum tuning condition becomes gradually lower than the case of r=1 and maximum amplitude becomes lower with an increment in the mass ratio. However, the impulse clearance is larger and the working range of restraining vibration amplitude become smaller with a decrement in the mass of impact ball.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1993.10a
• /
• pp.1043-1052
• /
• 1993

Field experiments were conducted to determine the optimum combination of performance parameters of a single-shank, tractor-mounted oscillating subsoiler. Tests were conducted at frequencies of oscillation of 3.7 , 5.67, 7.58, 9.48 and 11.456Hz ; amplitudes of 18, 21, 23.5, 34 and 36.5 mm ; and forward speeds of 1.84, 2.19 and 3.42 kmph at moisture content close to the plastic limit of the soil. It was observed that there was a reduction in average draft but an a increase in average total power requirement for oscillating than non-oscillating subsoiling. The draft and power ratios were significantly affected by the forward speed, frequency and amplitude. Their combined interaction expressed in terms of the velocity ratio parameter( the ratio of peak tool velocity and forward speed) however has the strongest influence. At the same velocity ratio, the draft reduction and power increase were less at higher amplitude of oscillation . As the oscillating frequency is increased toward the soil resonance the draft requirement becomes less. For the field conditions tested. the optimum operation was obtained at an amplitude of 36.5mm, frequency of 9.48Hz and speed of 2.19 kmph with a draft ratio of 0.33 and a power ratio of only 1.24.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2001.04a
• /
• pp.365-372
• /
• 2001

This study is concerned with the application of an analytical model of cyclic crack growth that includes the effects of crack closure. The crack closure model is based on the Dugdale model and the strip model, considering the plasticity-induced closure which is caused by residual plastic deformation remaining in the wake of an advancing crack. This study is performed to get the relation between crack growth and crack opening stress with the constant stress ratio, and the relation between stress ratio and crack opening stress with the constant maximum stress under constant-amplitude loading. Under constant-amplitude loading, the crack opening stress is conversed the constant value as a crack grows and is proportion to both the stress ratio and the maximum stress. The crack closure effect, however, is decreased in the positive stress ratio and disappeared at about 0.7. The crack growth analysis using the crack closure model shows that the influence of stress ratio is minimized in the relation between crack growth ratio and effective stress intensity range specially at the negative stress ratio.