• Journal of Sensor Science and Technology
• /
• v.6 no.6
• /
• pp.451-457
• /
• 1997

The thick films of oxide semiconductors such as $WO_{3}$, $SnO_{2}$ and ZnO for the $NO_{2}$ detection of sub-ppm range have been prepared and their characteristics were investigated. It is showed that the optimum operating temperatures of the sensors are $300^{\circ}C$ and $220{\sim}260^{\circ}C$ for $WO_{3}$-based and $SnO_{2}$-based thick films, and ZnO-based thick films, respectively. Since the resistance of ZnO-based thick films are extremely high($>10^{6}{\Omega}$), the signal to noise ratio was comparatively low. In order to determine the selectivity, the films are exposed to the interfering gases such as ozone, ammonia, methane and the mixture of carbon monoxide and propane. $WO_{3}$-ZnO(3 wt.%) and $SnO_{2}-WO_{3}$(3 wt.%) thick film sensors show high sensitivity, good selectivity, excellent reproducibility and the linearity of $NO_{2}$ concentration versus sensor resistance. The preliminary results clearly demonstrated that the sensor can be successfully applied for the detection of $NO_{2}$ in sub-ppm range.

• Korean Journal of Ecology and Environment
• /
• v.43 no.2
• /
• pp.212-220
• /
• 2010

Effects of sediment and toxic cyanobacterium Microcystis aeruginosa on feeding behaviors of an omnivorous fish, gold fish (Carassius auratus) were examined in laboratory and in situ mesocosm. Laboratory feeding experiments were performed in small aquaria (7 L) with cyanobacterial blooms (mainly M. aeruginosa) under the condition of sediments and no-sediments, and toxic (NIES-298) and non-toxic M. aeruginosa (NIES-101). In situ feeding experiments were conducted at the shore of eutrophic lake (Lake Ilgam, Seoul) in the mid-July, 2005. Results showed that fish introduction decreased the concentration of Chlorophyll-a (Chl-a) at higher rate in no sediment-containing aquaria. In contrast, there was a drastic increase of Chl-a in the sedimentcontaining aquaria. Fish effectively removed the M. aeruginosa cells without algal toxin (microcystin). Fish also selectively removed the large size Chl-a (>$50{\mu}m$), although all kinds of nutrients were increased after fish introduction, especially ammonia. Our results indicate that the strategic introduction of domestic omnivores Carassius auratus, to control cyanobacterial bloom in eutrophic lake will negatively play in the water quality improvement via a sediment disturbance and a density-dependent digestion.

• Fisheries and Aquatic Sciences
• /
• v.19 no.8
• /
• pp.32.1-32.6
• /
• 2016

A feeding trial was conducted to evaluate the effects of two different sizes of extruded pellets (EP) ($EP_1$ - 3 mm or $EP_2$ - 5 mm) and a moist pellet (MP) in olive flounder, Paralichthys olivaceus, reared in semi-recirculation system. A total of 450 fish with an average initial weight of $5.0{\pm}0.2g$ (mean ${\pm}$ SD) were fed one of the three experimental diets in triplicate groups. At the end of a 6-week feeding trial, weight gain, specific growth rate, and feed efficiency of fish fed EP diets were significantly higher than those of fish fed MP (P < 0.05). Water quality parameters like turbidity, total ammonia nitrogen, and total phosphorous from tanks of fish fed $EP_1$ and $EP_2$ were significantly lower than those from tanks of fish fed MP. Blood plasma glutamic oxaloacetic transaminase and glucose concentration were significantly higher in fish fed MP diet compared to fish fed EP diets (P < 0.05). Whole body crude protein contents in fish fed EP diets were higher than those from the fish fed MP diet. Whole body amino acid content like threonine, aspartic acid, serine, tyrosine, and cystine were found to be significantly higher in fish fed EP diets than those in fish fed MP diet. In considering overall performance of olive flounder, $EP_2$ diet could be recommended for the successful aquaculture of this important fish species.

• Korean Journal of Poultry Science
• /
• v.39 no.3
• /
• pp.207-213
• /
• 2012

This experiment was conducted to investigate the effects of various levels of dietary protein on laying performance and egg quality in laying quail. A total of six hundred forty 7-week-old laying type Japanese quail were divided into four groups with eight replicates per group (20 birds per replicate) and fed four diets differing in dietary protein levels (18, 20, 22 and 24%) with isocaloric corn-soybean meal-based diets for 8 weeks. The results showed no significant differences in feed intake and egg weight among the groups. With an increase in dietary protein levels, the egg production and daily egg mass were linearly increased (P<0.05). However, there were no significant differences in eggshell thickness and Haugh unit. The dietary protein did not affect the blood levels of GOT, GPT, BUN, albumin, and creatinine. The ammonia concentration of intestinal digesta was not affected by the dietary treatments. The contents of hepatic triacylglycerol in the groups fed diets containing 20% protein or more were significantly reduced as compared with that of 18% CP group (P<0.05). Overall, this study showed that relatively high levels of dietary CP are needed to sustain the higher egg production and daily egg mass and to avoid the hepatic triacylglycerol accumulation in Japanese quail.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.84-84
• /
• 2012

소자가 고집적화 됨에 따라, 비저항이 낮고 electro migration (EM), Stress Migration (SM) 특성이 우수한 구리(Cu)를 배선재료로서 사용하고 있다. 그러나, 구리는 Si과 $SiO_2$의 내부로 확산이 빠르게 일어나, Si 소자 내부에 deep donor level을 형성하고, 누설 전류를 증가시키는 등 소자의 성능을 저하시킬 수 있는 문제점을 가지고 있다. 그러나, electroplating 을 이용하여 증착한 Cu 박막은 일반적으로 확산 방지막으로 쓰이는 TiN, TaN, 등의 물질과의 접착 (adhesion) 특성이 나쁘다. 따라서, Cu CMP 에서 증착된 Cu 박막의 벗겨지거나(peeling), EM or SM 저항성 저하 등의 배선에서의 reliability 문제를 야기하게된다. 따라서 Cu 와 접착 특성이 좋은 새로운 확산방지막 또는 adhesion layer의 필요성이 대두되고 있다. 본 연구에서는 이러한 Cu 배선에서의 접착성 문제를 해결하고자 Metal organic chemical vapor deposition (MOCVD)을 이용하여 제조한 코발트(Co) 박막을 $Cu/TaN_x$ 사이의 접착력 개선을 위한 adhesion layer로 적용하려는 시도를 하였다. Co는 비저항이 낮고, Cu 와 adhesion이 좋으며, Cu direct electroplating 이 가능하다는 장점을 가지고 있다. 하지만, 수소 분위기에서 $C_{12}H_{10}O_6(Co)_2$ (dicobalt hexacarbonyl tert-butylacetylene, CCTBA) 전구체에 의한 MOCVD Co 박막의 경우 탄소, 산소와 같은 불순물이 다량 함유되어 있어, 비저항, surface roughness 가 높아지게 된다. 따라서 구리 전착 초기에 구리의 핵 생성(nucleation)을 저해하고 핵 생성 후에도 응집(agglomeration)이 발생하여 연속적이고 얇은 구리막 형성을 방해한다. 이를 해결하기 위해, MOCVD Co 박막 증착 시 수소 반응 가스에 암모니아를 추가로 주입하여, 수소/암모니아의 분압을 1:1, 1:6, 1:10으로 변화시켜 $Co/TaN_x$ 박막의 특성을 비교 분석하였다. 각각의 수소/암모니아 분압에 따른 $Co/TaN_x$ 박막을 TEM (Transmission electron microscopy), XRD (X-ray diffraction), AES (Auger electron spectroscopy)를 통해 물성 및 조성을 분석하였고, AFM (Atomic force microscopy)를 이용하여, surface roughness를 측정하였다. 실험 결과, $Co/TaN_x$ 박막은 수소/암모니아 분압 1:6에서 90 ${\mu}{\Omega}-cm$의 낮은 비저항과 0.97 nm 의 낮은 surface roughness 를 가졌다. 뿐만 아니라, MOCVD 에 의해 증착된 Co 박막이4-6 % concentration 의 탄소 및 산소 함량을 가지는 것으로 나타났고, 24nm 크기의 trench 기판 위에 약 6nm의 $Co/TaN_x$ 박막이 매우 균일하게 형성된 것을 확인 할 수 있었다. 이러한 결과들은, 향후 $Co/TaN_x$ 박막이 Cu direct electroplating 공정이 가능한 diffusion barrier로서 성공적으로 사용될 수 있음을 보여준다.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.9
• /
• pp.879-886
• /
• 2010

This study investigated the removal characteristics of highly concentrated $NH_4$-N and $PO_4$-P by struvite crystallization using converter slag as a seed crystal. The optimal pH range for removal and recovery of $NH_4$-N and $PO_4$-P by struvite crystallization was measured to be 8.0~8.75, in which total removal efficiencies for $NH_4$-N and $PO_4$-P by struvite precipitation and crystallization were 34.3~61.0% and 91.0~96.2%, respectively. The maximum removal efficiencies for $NH_4$-N and $PO_4$-P by struvite crystallization were 29.4% at pH 8.5 and 65.1% at pH 8.0, respectively. The removal efficiency of $NH_4$-N by struvite crystallization decreased with increasing calcium ion concentration. The analysis results of SEM, EDS and XRD exhibited that $NH_4$-N and $PO_4$-P in meta-stable region of struvite crystallization could be eliminated through formation of magnesium ammonia phosphate (MAP) and hydroxyapatite (HAp) on seed crystals by struvite precipitation and crystallization.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.10
• /
• pp.901-908
• /
• 2009

We examine the processing method of the food wastewater to direct spray at living waste incinerator. The demoscale stoker system is used as a incineration facility. The results show that it brings effect on the reduction of nitrogen oxide ($NO_x$) concentration as well as the ammonia ($NH_3$) amount in SNCR (selective non-catalytic reduction) by the incineration of food wastewater which is containing a plentiful ammoniac nitrogen ($NH_3$-N). Furthermore, the stability of incineration facility and the extension of operation period is actualized as a improvement of clogging phenomenon on outer wall of water pipe as the 870~$950^{\circ}C$ maintain of exit temperature in a second combustor by spray of the food wastewater. The 26 items of air pollution matter of nitrogen oxide ($NO_x$), sulfur oxide ($SO_x$) and dioxin etc. are measured. The results show that it is under the value of allowable exhaust standard.

• Korean Journal of Food Science and Technology
• /
• v.34 no.5
• /
• pp.811-817
• /
• 2002

Korean traditional soy sauce was desalted using electrodialyzer, and their physicochemical properties were analyzed. The salt content of soy sauce significantly decreased from initial 18.9 (w/v) to 0.47% (w/v) and the volume also decreased to 330 mL when 1,000 mL of soy sauce was desalted for 450 min at a current of 2 A. During the desalting process, the numbers of viable cells of total bacteria, yeasts, and molds increased due to the concentration effect of the electrodialysis. Turbidity increased from 3.1 to 8.5, and total nitrogen, total sugar, and reducing sugar contents also increased. The pH, and amino nitrogen and volatile base nitrogen contents slightly decreased, with ammonia content significantly decreasing from 19.4 to $1.3\;{\mu}mol/mL$. Free amino acids content increased twofold after electrodialysis. Gas chromatograms of soy sauce showed that profiles of the flavoring compounds did not change when electrodialyzed for 360 min, but most were removed after 540 min.

• Korean Chemical Engineering Research
• /
• v.50 no.3
• /
• pp.435-441
• /
• 2012

The direct conversion of cellulose into polyols in $H_2$ was examined over Pt catalysts supported on various zeolites, viz., mordenite, Y, ferrierite, and ${\beta}$. For comparison, Pt catalysts supported on ${\gamma}-Al_2O_3$, $SiO_2-Al_2O_3$, and $SiO_2$ were also tested. The physical properties of the catalysts were probed with $N_2$ physisorption. The surface acidity was measured with temperature programmed desorption of ammonia ($NH_3$-TPD). The Pt content was quantified with inductively coupled plasma-atomic emission spectroscopy (ICP-AES). The Pt dispersion was determined with CO chemisorptions and transmission electron microscopy (TEM). The conversion of cellulose appeared to be mainly dependent on the reaction temperature and reaction time because it depends on the concentration of $H^+$ ions reversibly formed in hot water. Pt/H-mordenite (20) showed the highest yield to polyols among the tested catalysts. Pt/H-zeolite was superior to Pt/Na-zeolite for this reaction. The polyol yield was dependent on the surface acid density and the external surface area.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.4
• /
• pp.387-392
• /
• 2015

A method for measuring and analyzing the $NO_x$ in ships is described in $NO_x$ Technical Code 2008. The analysis device, as required by the Code, has been to use a Chemi-luminescence detection method or Heated Chemi-luminescence detection. on the other hand, selective catalytic reduction using $NH_3$ as a reducing agent has an interference effect on the analyzer, and causes measurement error. In this study, the Chemi-luminescence detection method was examined according to how it affects the concentration of $O_2$, CO, $SO_2$, $NH_3$. Fourier transform infrared spectrometry analysis equipment and measurement methods were compared. In order to confirm the effect of the physical interference of the measuring device, it was confirmed by decomposing a measuring device. Consequently, white precipitate and moisture were generated inside the chemiluminescence detection system and I found that affecting interference. The influence of interference highlights the need to consider the minimized $NO_x$ measurement method.