• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.15 no.5
• /
• pp.175-181
• /
• 2005

Ingots of rutile single crystals were grown by the skull melting method, and their characteristics were compared in terms of melt-dwelling time for each melt. The method is based on direct inductive heating of an electrically conducted melt by an alternating RF field, and the heating is performed by absorption of RF energy. $TiO_2$ is an insulator at room temperature but its electric conductivity increases elevated temperature. Therefore, titanium metal ring(outside diameter : 6cm, inside diameter : 4cm, thickness 0.2cm) was embedded into $TiO_2$, powder (anatase phase, CERAC, 3N) for initial RF induction heating. Important factors of the skull melting method are electric resistivity of materials at their melting point, working frequency of RF generator and cold crucible size. In this study, electric resitivity of $TiO_2$, $(10^{-2}\~10^{-1}\;{\Omega}{\cdot}m)$ at its melting point was estimated by compairing the electric resitivities of alumina and zirconia. Inner diameter and height of the cold crucible was 11 and 14cm, respectively, which were determined by considering of the Penetration depth $(0.36\~1.13cm)$ and the frequency of RF generator.

• Journal of Sensor Science and Technology
• /
• v.10 no.4
• /
• pp.239-249
• /
• 2001

LAPS is a device which is dependent on the bias potential between a pH sensitivity and alternating photocurrent. We implemented the multichannel LAPS device and the detection system which was able to effectively measure the sensor's output by a synchronized detection circuit and multiple methods. The implemented LAPS was structured the multiple sensing sites for analyzing a various components simultaneously. And the system included a time-division method using one pre-amplifier being able to detect the multichannel pH concentration preserving a high S/N ratio and a control part. System hardware consists of a pre-amplifier, digital unit and sensor unit, and software consists of a system program and PC program. As results, we verified the successful operations of system including an implemented pre-amplifier and signal processing units.

• Journal of the Korean Electrochemical Society
• /
• v.14 no.4
• /
• pp.225-230
• /
• 2011

CIGS solar cells are kind of thin film solar cells, which are studied several years. CdS buffer layer that makes heterojunction between window layer and absorbing layer was one of issue in the CIGS solar cell study. New types of buffer layer consisted of indium sulfide are being studied these days owing to high price and environmental harmful of CdS. In this study, we demonstrated electrochemical synthesis of indium sulfide film as a buffer layer, which is cheaper and faster than other methods. A uniform indium sulfide film was obtained by applying two different alternating potentials. The band gap of the film was optimized by controlling temperature during the electrochemical synthesis. Using x-ray photoelectron spectroscopy and diffraction method we confirmed that ${\beta}$-indium sulfide was formed on ITO electrode surface.

• Journal of Korean Medical classics
• /
• v.23 no.6
• /
• pp.97-108
• /
• 2010

Salt is a vital inorganic substance to human body and is seasoning in food. It is an absolute alternating factor on fermented food. What's more, in the oriental medicine, it is widely used to raise the pharmacological effect as a component of a prescription when processing a medicine, and when taking the medicine. Though, Importance of salt is often unaware and it is not used in the right way. focusing on "東醫寶鑑 內景篇 Donguibogam-Naegyeong" I categorized the methods of salt's prescription, dose, processing, seasoning, etc. The contents were compared and studied as well. When salt is used as a medicine, It is used as a main medicine, complimentary(aid) medicine, Jjim-Jil(hot towel or bath etc), vomiting medicine and gargling water. when taking the salt water with other medicine, depending on the type of the medicine, boiled salt water, warm alcohol or salt water, mixing powder medicine with salt water etc The methods are diverse. The reason to process medicine with salt or salt water is to bring the pharmacological Qi(energy) down to increase remedial value. When processing a medicine, kneading dough with salt water and the case using food ingredient as medicine salt was used as seasoning. Kneaded mud with salt were used to cover medicine or on the outer surface. This proves that it prevents the dryness and helps the medicine cooked even. Like this, salt is vital and highly-valued medicine in the oriental medicine. learning the right method of using salt and if it were used properly It is considered that it would increase the Pharmacological effect.

• Journal of Power Electronics
• /
• v.14 no.6
• /
• pp.1303-1313
• /
• 2014

Dynamic behavior of the harmonic detection part of an active power filter (APF) has an essential role in filter compensation performances during transient conditions. Instantaneous power (p-q) theory is extensively used to design harmonic detectors for active filters. Large overshoot of p-q theory method deteriorates filter response at a large and rapid load change. In this study the harmonic estimation of an APF during transient conditions for balanced three-phase nonlinear loads is conducted. A novel fuzzy instantaneous power (FIP) theory is proposed to improve conventional p-q theory dynamic performances during transient conditions to adapt automatically to any random and rapid nonlinear load change. Adding fuzzy rules in p-q theory improves the decomposition of the alternating current components of active and reactive power signals and develops correct reference during rapid and random current variation. Modifying p-q theory internal high-pass filter performance using fuzzy rules without any drawback is a prospect. In the simulated system using MATLAB/SIMULINK, the shunt active filter is connected to a rapidly time-varying nonlinear load. The harmonic detection parts of the shunt active filter are developed for FIP theory-based and p-q theory-based algorithms. The harmonic detector hardware is also developed using the TMS320F28335 digital signal processor and connected to a laboratory nonlinear load. The software is developed for FIP theory-based and p-q theory-based algorithms. The simulation and experimental tests results verify the ability of the new technique in harmonic detection of rapid changing nonlinear loads.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.10
• /
• pp.699-705
• /
• 2001

Six types of planar thermal converters from TC 1 to TC 6 were designed and fabricated for the purpose of being used as practical standards to alternating current. The respective voltage responses in air and in a vacuum of TC 6, which has the smallest thermal loss, were about 4.03mV/mW and about 6.38 mV/mW. Thermal time constant of TC 6, which has also the smallest heater thermal inertia, was about 8 ms. The respective variations of AC-DC voltage and current transfer errors from sample to sample, which were measured by FRDC(fast reversed DC) method, were about $\pm$0.41 ~$\pm$0.85 ppm and about $\pm$0.15~$\pm$1.16 ppm in the frequent range of 40 Hz~10 KHz with appling 1 V and 5 mA rms sine waves to the converters. All converters investigated exhibited sufficiently low AC-DC transfer errors to be used as practical standards.

• Journal of Advanced Navigation Technology
• /
• v.11 no.2
• /
• pp.177-186
• /
• 2007

In this paper, the optimal position offset of optical phase conjugator (OPC) and the optimal dispersion offsets of fiber sections, which are alternating with the method for the symmetry of optical power and chromatic dispersion with respect to OPC, are numerically investigated as afunction of the WDM channel numbers. The WDM channel numbers are assumed to be 8, 12, 16, 20 and 24. The bit-rate of each channel is assumed to be 40 Gbps for all cases. It is confirmed that the optimal position offset of OPC and optimal dispersion offset of fiber section are gradually increased as the WDM channel numbers are gradually increased. But, the optimal dispersion values of fiber sections per OPC position offset of 1 km are independent on WDM channel numbers, because the optimal position offset of OPC and optimal dispersion offset of fiber section are simultaneously increased as the WDM channel numbers are increased. It is also confirmed that the applying of these optimal parameter values is efficient to WDM system with many channels rather than WDM with small channels.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.259.1-259.1
• /
• 2014

Recently non-thermal plasma has been frequently applied to various research fields. The liquid plasma have received much attention lately because of interests in surgical and nanomaterial synthesis applications. Especially, intensive researches have been carried out for non-thermal plasma in liquid by using various electrode configurations and power supplies. We have developed a bioplasma source which could be used in a liquid, in which outer insulator has been covered onto the outer electrode. Also we have also put an insulator between the inner and outer electrode. Based on the surface discharge mode, the nonthermal bioplasma has been generated inside a liquid by using an alternating current voltage generator with peak voltage of 12 kV under driving frequency of 22 KHz. Here the discharge voltage and current have been measured for electrical characteristics. Especially, We have measured discharge and optical characteristics under various liquids of deionized (DI) water, tap water, and saline by using monochromator. We have also observed nitric oxide (NO), hydrogen peroxide (H2O2), and hydroxyl (OH) radical species by optical emission spectroscopy during the operation of bioplasma discharge inside various kinds of DI water, tap water, and saline. Here the temperature has been kept to be $40^{\circ}C$ or less when discharge in liquid has been operated in this experiment. Also we have measured plasma temperature by high speed camera image and density by using either H-alpha or H-beta Stark broadening method.

• Polymer(Korea)
• /
• v.29 no.4
• /
• pp.392-398
• /
• 2005

Self-assembled multilayer thin films of poly(ethylene-alt-maleic anhydride) (PEMAh) and poly(4-vinyl pyridine) (P4VP) were fabricated by layer-by-layer (LbL) sequential adsorption. Fourier transform infrared (FT-IR) spectroscopic analysis of the self-assembled PEMAh/P4VP multilayer films confirms that the driving forces for the multilayer buildup are the intermolecular hydrogen bonding and electrostatic interactions. The linear increase of absorption peak of P4VP at 256 nm with increasing number of PEMAh/P4VP bilayers indicates that the multilayer buildup is an uniform assembling process. We also investigate the effects of polyelectrolyte concenhation variation of the dipping solution and pH variation of the PEMAh solution on the multilayer film formation. Thickness. adsorbed polyelectrolyte mass and surface roughness of the multilayer films were measured by UV-visible spectroscopy, quartz crystal microbalance (QCM), and atomic force microscopy (AFM), respectively.

• Journal of Korean Ophthalmic Optics Society
• /
• v.7 no.1
• /
• pp.75-78
• /
• 2002

Thirty three layer $TiO_2/SiO_2$ coating mirrors with high reflectance through a 620~820nm wavelength range have been designed and fabricated by electron beam evaporation method. Multilayer films were deposited on glass(BK7) and sequentially. The high reflector design is based on alternating high and low refractive index layers. $n_H$ and $n_L$ such that a "stopband"(or area of high reflectivity) is created that is centered around the design wavelength. ${\lambda}_0$. The measured transmittance spectrum with an incident wavelength at an incident angle of $40^{\circ}{\pm}7^{\circ}$ exhibited a reflectance of 99.9% at the wavelength of 620~820nm but high peak transmittance in the wavelength region from 700 to 740nm.