• The Journal of Korean Academy of Prosthodontics
• /
• v.45 no.4
• /
• pp.431-443
• /
• 2007

Statement of problem: Injuries along with discomfort may result on the oral mucosa when non-rigid material is used as the major connector in construction of RPD, since nonrigid major connectors transmit unstable forces throughout the appliance. Titanium which recently draws attention as a substitute of Co-Cr had a difficulty in fabricating due to high melting temperature but the development of casting technique makes it possible to apply to the clinical case. Purpose: The purpose of this study was to investigate the rigidity and the castability of titanium upper major connector by design and make a comparison with Co-Cr major connectors which are widely used in clinical cases now. Material and methods: Casting was done using CP-Ti(Grage 2) (Kobe still Co., Japan) for the experimental groups, and 4 various designs namely palatal strap, U-shaped bar, A-P strap, and complete palatal plate were casted and 5 of each designs were included in each group. For the experimental group, Universal testing machine (Model 4502; Instron, Canton, Mass) was used to apply vertical torsional force vertically to the horizontal plane of major connector. In the second experiment, Vertical compressive force was applied to the horizontal plane of major connector. As a comparative group, Co-Cr major connector was equally manufactured and underwent the same experimental procedures Strain rate was measured after constant loading for one minute duration, and statistical analysis was done with SPSS ver.10.0 for WIN(SPSS. Inc. USA). From the one-way ANOVA and variance analysis (P=0.05), Scheffe's multiple comparison test implemented. Results: 1. Least amount of strain was observed with complete palatal plate followed by A-P bar, palatal bar, and the U-shaped bar having most amount of strain. 2. In all designs of titanium major connector, less strain rate was observed under compressive loading than under torsional loading showing more resistance to lateral force. 3. For titanium major connector, less strain rate was observed when the force is applied to the first premolar area rather than to the second molar area indicating more strength with shorter length of lever. 4. In Comparison of Co-Cr major connector with titanium major connector, palatal strap and U-shaped bar designs showed higher strength under torsional force that is statically significant, and under compressive force, no significant difference was observed expert for U-shaped bar. 5. In titanium major connector, complete palatal plate showed lowest success rate in casting when compared with the Co-Cr major connector. Conclusion: Above results prove that when using titanium for major connector, only with designs capable of generating rigidity can the major connector have almost equal amount of rigidity as Co-Cr major connector and show lower success rate in casting when compared with the Co-Cr major connector.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1999.04a
• /
• pp.287-294
• /
• 1999

The tensegrity structure by prestressed cable, which may have large freedom in scale and form and therefore are received much attention from the view points of their light weight and aesthetics, is a very flexible and geometrically unstable structure because the cable material has little initial rigidity. For the stable self-equilibrated state of the usually very deformable structure, the method to find the optimal initial stress by the shape analysis is proposed in this paper. The proposed procedure is to derive the nonlinear finite element formula of cable and truss members considering geometric nonlinearity and used to modified load incremental method adding to Newton-Raphson method with the proposed condition for optimal initial stress. The result of the shape analysis for the tensegrity structure with the radius of 30m is shown the almost approximated shape to architectural shape and the changed procedure of initial stress

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1999.04a
• /
• pp.335-342
• /
• 1999

It is well known that l-girders are weak in torsion and it might be more economical to use a box girder, which has great torsional rigidity. The use of box beams does, however, present a potential problem in that cross-sectional distortions can induce large warping normal stresses and transverse bending stress. Accordingly a sufficient number of diaphragms are provided to make the distortional effects minimal. In engineering practice, diaphragms are spaced in 5m intervals without reasonable basis. It is considered to be noneconomical design to the almost design engineers, and it may produce the unsafe structural systems in special cases such as curved bridges with large initial curvature. These problems have not been solved for the lack of adequate tools of structural analysis. In this study, on the basis of the parametric studies, the design formulas for the distortional warping stress and the reasonable diaphragm spacing of box girder were presented.

• Journal of the Korean Home Economics Association
• /
• v.26 no.1
• /
• pp.11-19
• /
• 1988

Bending properties of 168 commercial silk fabrics and polyester fabrics for korean women's clothes were tested by KES-F system. Samples were classified into for summer, fall & winter fabrics. In this study, bending regidity(B) and bending hysteresis(2HB) were measured, then 2HB/W, {{{{ SQRT { 2HB/W} }}}}, 2HB/B which are concerning to formation of weared clothes and transformation behavior were investigated. fabrics for korean women's silk clothes for fall & winter were compared with fabrics for japanese kimono clothes on the bending properties. The results were as follows : 1. The bending regidity of silk fabrics were higher than polyester fabrics and bending hysteresis of fall & winter fabrics were higher than summer fabrics. 2. The 2HB/W and {{{{ SQRT { 2HB/W} }}}} of polyester fabrics were lower than silk fabrics. 3. the silk fabrics for summer clothes were the least in 2HB/B. 4. Silk fabrics for korean women's clothes were almost the same in bending rigidity, bending hysteresis and thickness of fabrics for japanese kimono clothes, but weight of the silk fabrics were lower to fabrics for jpanese kimono clothes.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.43 no.1
• /
• pp.29-35
• /
• 2011

Since the role of lignin in the wood cell wall is to keep integrity and structure rigidity of lignocellulosic substrate, lignin of the cell wall has to be destroyed before enzymatic hydrolysis of wood polysaccharides. The aspen wood meals were delignified with ozone in acidic condition. The chemical characteristics of wood meal were investigated. The 60% of lignin and almost zero % of polysaccharides in aspen wood meal was degraded with 10min. ozone treatment. The phenolic hydroxyl groups of lignin in ozonated wood meal were increased with ozonation time. The sugar composition of ozonated wood meal showed that the hemicellulose was more susceptible to ozonation than cellulose. The yield of aldehyde was increased in some degree with 10min. ozone treatment and decreased with longer ozone treatment.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.18 no.3
• /
• pp.328-335
• /
• 2009

In order to 1ransport the steel roll coil effectively and safely to the destination, the stability of the steel roll coil which induced the minimum movements during the 1ransportation was s1rongly required. The basic 1ransportation equipment for the steel roll coil such as the wedge is made of 100% imported wood known as the apitong. However, the material characteristic such as the rigidity has caused permanent damages to the steel roll coil and the damaged steel roll coils were not easily restorable. Thus it was unsuitable for other purposes. The introduction of new materials to manufacturing wedges which would have a good recovery performance and thus enable the wedge prevention or reduction to the steel roll coil or any other products during the 1ransportation is needed. Due to the fact that recovering damage of the coil is almost impossible, we have to find the new type of wedge that can substitute the apitong wedge. Therefore, we are going to develop a wedge that does not damage rolled steel coil and has better recovery and softness than existing apitong wedge.

• Journal of the Korean School Mathematics Society
• /
• v.1 no.1
• /
• pp.131-138
• /
• 1998

The aims of mathematical education are to improve uniformity and rigidity, and to apply to an information age which our society demands. One of the educational aims in the 6th educational curriculum emphasizes on the expansion of mathematical thought and utility, But, The change of contents in the text appears little. This means that mathematical teachers must actively develop the new types of problems. That the interests and concerns about mathematics lose the popularity and students recognize mathematics burdensome is the problems of not only teaching method, unrealistically given problems but abstractiveness and conceptions. Mathematical Modeling is classified exact model, almost exact theory based model and impressive model in accordance with the realistic situation and its equivalent degree of mathematical modeling. Mathematical Modeling is divided into normative model and descriptive model according to contributed roles of mathematics. The Modeling Applied Problems in the present text are exact model and stereotyped problems. That the expansion of mathematical thought in mathematics teaching fell into insignificance appears well in the result of evaluating students. For example, regardless of easy or hard problems, students tend to dislike the new types of mathematical problems which students can solve with simple thought and calculation. The ratings of the right answer tend to remarkably go down. If mathematical teachers entirely treat present situation, and social and scientific situation, students can expand the systematic thought and use the knowledge which is taught in the class. Through these abilities of solving problems, students can cultivate their general thought and systematic thought. So it is absolutely necessary for students to learn the Modeling Applied Problems.

• Earthquakes and Structures
• /
• v.10 no.5
• /
• pp.1049-1066
• /
• 2016

An approximate analysis is presented for multi-story setback buildings subjected to ground motions. Setback buildings with mass and stiffness discontinuities are common in modern architecture and quite often they are asymmetric in plan. The proposed analysis provides basic dynamic data (frequencies and peak values of base resultant forces) and furthermore an overview of the building response during a ground excitation. The method is based on the concept of the equivalent single story system, which has been introduced by the author in earlier papers for assessing the response of uniform in height buildings. As basic quantities of the dynamic response of elastic setback buildings can be derived by analyzing simple systems, a structural layout of minimum elastic rotational response can be easily constructed. The behavior of such structural configurations, which is basically translational into the elastic phase, is also examined into the post elastic phase when the strength assignment of the various bents is based on a planar static analysis under a set of lateral forces simulating an equivalent 'seismic loading'. It is demonstrated that the almost concurrent yielding of all resisting elements preserves the translational response, attained at the end of the elastic phase, to the post elastic one.

• Structural Engineering and Mechanics
• /
• v.62 no.5
• /
• pp.587-593
• /
• 2017

The objective of this analytical study is to calculate the elasto-plastic stresses of Functionally Graded (FG) hyperbolic disc subjected to uniform temperature. The material properties (elastic modulus, thermal expansion coefficient and yield strength) and the geometry (thickness) of the disc are assumed to vary radially with a power law function, but Poisson's ratio does not vary. FG disc material is assumed to be non-work hardening. Radial and tangential stresses are obtained for various thickness profile, temperature and material properties. The results indicate that thickness profile and volume fractions of constituent materials play very important role on the thermal stresses of the FG hyperbolic discs. It is seen that thermal stresses in a disc with variable thickness are lower than those with constant thickness at the same temperature. As a result of this, variations in the thickness profile increase the operation temperature. Moreover, thickness variation in the discs provides a significant weight reduction. A disc with lower rigidity at the inner surface according to the outer surface should be selected to obtain almost homogenous stress distribution and to increase resistance to temperature. So, discs, which have more rigid region at the outer surface, are more useful in terms of resistance to temperature.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.05a
• /
• pp.102-103
• /
• 2014

Due to the nature of the existing load, the criteria of assessing the intensity of the lightweight wall's impact resistance has been though of as obscure. The current study, therefore, focuses on the standardized assessment of the impact resistance to the force of the large soft body applying to the lightweight wall. The gypsum board wall showed a low level of the maximum residual displacement. It is, however, required to be careful about the selection of the finishing process since the high level of the maximum displacement is likely to cause harm to finishing materials. Unlike the gypsum board, the ALC block wall displayed a considerable rigidity while showing almost no maximum residual displacement. Even with the low level of the maximum displacement due to the stiffness, the ALC block wall is still likely to be affected by the vibration derived from any impact on the surface, which demands a need for additional study. The future experimental study, accordingly, will focus on the impact of the vibration on finishing materials, consequently leading to the accurate prediction of the possibility of potential damage to the lightweight wall caused by the large soft body.