• Transactions on Electrical and Electronic Materials
• /
• 제11권6호
• /
• pp.279-284
• /
• 2010

This study has been carried out to determine the optimal process conditions of $AZO:H_2$ thin films for the maximization of the transmittance of a blue GaN light-emitting diode (LED) with a wavelength of 470 nm. The Al-doped zinc oxide $(AZO):H_2$ thin films were deposited on a sapphire substrate by radio-frequency magnetron sputtering system with varying substrate temperatures, working pressures and annealing temperatures temperature, working pressure and annealing imposed on a AZO (2wt% $Al_2O_3$) ceramic target. The effect of these variables was investigated in order to improve the light extraction efficiency of the LED. As a result, the (002)-oriented peak was found in all the $AZO:H_2$ thin films. The lowest resistivity and the best transmittance at a wavelength of 470 nm was found to be $4.774\;{\times}\;10^{-4}\;{\Omega}cm$ and 92% at a substrate temperature of $500^{\circ}C$, working pressure of 7 mTorr and annealing temperature of $400^{\circ}C$. The transmittance of the $AZO:H_2$ thin film for the Blue GaN LED was improved by approximately 13% relative to that of a ITO thin film (T = 79%).

• The Journal of Advanced Prosthodontics
• /
• 제7권5호
• /
• pp.343-348
• /
• 2015

PURPOSE. The purpose of this study was to evaluate the bond strength of composite resin on the fracture surface of metal-ceramic depending on the repair systems and surface roughening methods. MATERIALS AND METHODS. A total of 30 disk specimens were fabricated, 15 of each were made from feldspathic porcelain and nickel-chromium base metal alloy. Each substrate was divided into three groups according to the repair method: a) application of repair system I (Intraoral Repair Kit) with diamond bur roughening (Group DP and DM), b) application of repair system I with airborne-particle abrasion (Group SP and SM), and c) application of repair system II (CoJet Intraoral Repair System, Group CP and CM). All specimens were thermocycled, and the shear bond strength was measured. The data were analyzed using the Kruskal-Wallis analysis and the Mann-Whitney test with a significance level of 0.05. RESULTS. For the porcelain specimens, group SP showed the highest shear bond strength ($25.85{\pm}3.51MPa$) and group DP and CP were not significantly different. In metal specimens, group CM showed superior values of bond strength ($13.81{\pm}3.45MPa$) compared to groups DM or SM. CONCLUSION. Airborne-particle abrasion and application of repair system I can be recommended in the case of a fracture localized to the porcelain. If the fracture extends to metal surface, the repair system II is worthy of consideration.

• The Journal of Korean Academy of Prosthodontics
• /
• 제50권3호
• /
• pp.204-209
• /
• 2012

Surgical extrusion, immediate extrusion following tooth luxation, is a method to preserve one's natural tooth and achieve esthetic restoration without additional periodontal surgery when subgingival dental caries or crown fracture occurs. A 16-year-old male was referred to the clinic from the department of operative dentistry for the esthetic restoration of maxillary left lateral incisor. Due to the crown to root fracture, the tooth was endodontically treated with a buccal crown length of 4 mm. When the palatal flap was elevated, the mesiopalatal cervical fracture area was situated 3-4 mm subgingivally. Crown lengthening was achieved through surgical extrusion. After 3 months of clinical observation and provisional restoration, the maxillary left central incisor was restored with all ceramic crown and obtained a satisfactory clinical result.

• The Research Journal of the Costume Culture
• /
• 제22권4호
• /
• pp.605-618
• /
• 2014

This study aims to compare the ease of men's slim pants patterns, and to analyze the fit and appearance through the 3D virtual garment system. The study selected four educational materials and one industrial pattern of slim pants for a total of five items. The CLO 3D Modelist program was utilized to carry out the appearance evaluation through virtual wearing and opacity, and a comparison was performed regarding the clothing pressure when the virtual model was standing and walking. The results of our comparison of the patternmaking for slim pants showed that pattern C pants had the greatest ease on the waist circumference, while B pants showed no ease. The C and E pants also had the most ease on the hip measurement. In the appearance evaluation, A pants received the most favorable results, followed by D, E, B, and C, in descending order. The clothing pressure appeared to be mainly red on the waist, crotch, and hem when standing in all pants, so the clothing pressure was high. While walking, the stress appeared to be different for the left and right parts of the body, and the most significant difference was observed on the thigh area.

• Design & Manufacturing
• /
• 제10권3호
• /
• pp.14-19
• /
• 2016

Thermally or electrically conductive filler reinforced polymer composites are extensively being developed as the demand for light weight material increases rapidly in industiral applications need good conductivity such as heat sink of the electronics or light. Carbon or ceramic materials like graphite, carbon nanotube or boron nitride are typical conductive fillers with good thermal or electical conductivity. Using these conductive fillers, the polymer composites in the market show wide range of thermal conductivity from approximately 1 W/mK to 20 W/mK, which is quite enhanced considering the thermal conductivity lower than 0.5 W/mK for most polymeric materials. The practical use of these composites, however, is yet limited to specific applications because most composites are still not conductive enough or too difficult to process, too brittle, too expensive for higher conductivity. For practical use of conductive composite, the thermal conductivity required depending on the heat releasing mode are studied first for simplified unit cooling geometry to propose thermal conductivities of the composites for reasonable cooling performance comparing with the metal heat sink as a reference. Also, as a practical design for heat sink based on polymer composite, composite and metal sheet hybrid structures are investigated for LED lamp heat sink and audio amplication module housing to find that this hybrid structure can be a good solution considering all of the cooling performance, manufacturing, mechanical performance, cost and weight.

• Journal of the Microelectronics and Packaging Society
• /
• 제12권4호통권37호
• /
• pp.359-363
• /
• 2005

The organic insulation devices with MIM (metal-insulator-metal) structures as PVP gate insulation films were prepared for the application of organic thin film transistors (OTFT). The co-polymer organic insulation films were synthesized by using PVP(poly-4-vinylphenol) as solute and PGMEA (propylene glycol monomethyl ether acetate) as solvent. The cross-linked PVP insulation films were also prepared by addition of poly (melamine-co-formaldehyde) as thermal hardener. The leakage current of the cross-linked PVP films was found to be about 300 pA with low current noise. and showed better property in electrical properties as compared with the co-polymer PVP insulation films. In addition, cross-linked PVP insulation films showed better surface morphology (roughness), showing about 0.11${\~}$0.18 nF in capacitance for all PVP film samples.

• The Korean Journal of Ceramics
• /
• 제4권3호
• /
• pp.193-198
• /
• 1998

This paper presents the effects of an initial braking velocity, a braking pressure, and the number of braking stop on the tribological behaviors for the three different C-C composites using an inertia dynamic-friction tester. The C-C composites were prepared through the processes of several cycles of pitch impregnation/carbonization with different friction surface texture such as continuous 8-harness satin fabric (ADD-1), chopped fiber (ADD-2) and chopped fiber (ADD-3) having higher fiber volume fraction on friction than ADD-2 by about 10%. ADD-1 exhibited a higher fraction coefficient (0.41~0.33) than those of ADD-2 and ADD-3 (0.32~0.26) under the various initial braking velocities and braking pressures. The fraction coefficients decreased with increasing the initial velocity and the braking pressures. Wear rate by the thickness change after every 25 stop indicated that ADD-2 and ADD-3 having 1.7~2.7 $\mu\textrm{m}$/stop/pair were much lower than that of ADD-1 showing 5.0~6.5 $\mu\textrm{m}$/stop/pair. All specimens showed a little bit lower wear rate during the middle stage than the initial and latter stages among 100 braking stops. ADD-1 showed higher friction coefficient and wear rate due to the active pull-out of the fibers, evidenced by thicker were film and wear debrises.

• Journal of Technologic Dentistry
• /
• 제32권3호
• /
• pp.255-264
• /
• 2010

Purpose: This study was conducted to corroborate factors affecting dental technicians recognition states of their job consciousness. Methods: Self-administering questionnaires were distributed directly to some 200 registered female dental technicians in metropolis, small & medium-sized cities, farming and fishing villages of whom 153(76.5%) female dental technicians and female students responded in December, 2009. Information on recognition states of female dental technicians and female students in department of dental technology possible occupational mind and other general characteristics was gathered. Analysis of data was processed by use of X2-test and multiple regression analysis. Results: The recognition states of occupational satisfaction were higher in female students than female dental technicians(p<.05). They were observed that between respondents with more than five years of work and less than five years of career(p<.05). Statistically significant differences were observed in recognition values of female dental technicians occupational satisfaction between high and low groups of internal characteristic of their position and all ceramic part(p<.05). Conclusion: For woman dental technicians, the most predictive variables for recognition values of occupational satisfaction were an age, between groups, which of part and career(p<.05). Finally, this result suggests the facts that in order to achieve self-realization through the work experience, women herself should get rid of the dichotomous diagram and should change the consciousness of traditional role normals.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• 제21권3호
• /
• pp.227-231
• /
• 2008

In this study, in order to improve the electrical properties of low temperature sintering piezoelectric ceramics, $[0.05Pb(Zn_{1/2}W_{1/2})-0.07Pb(Mn_{1/3}Nb_{2/3})-0.088Pb(Zr_{0.48}Ti_{0.52})]O_3$(abbreviated as PZW-PMN-PZT) ceramic systems were fabricated using $Bi_2O_3$, CuO and $Li_2CO_3$ as sintering aids and then their piezoelectric and dielectric properties were investigated according to the amount of $Li_2CO_3$ and post-annealing process. Post-annealing process enhanced all physical properties except for mechanical quality factor (Qm). 0.2 wt% $Li_2CO_3$ added and post-annealed specimen showed the excellent values suitable for low loss piezoelectric actuator application as follow: the density = 7.86 $g/cm^3$ electromechanical coupling factor (kp) = 0.575, piezoelectric constant $d_{33}$ = 370 pC/N, dielectric constant ($\varepsilon_r$) = 1546, and mechanical quality factor (Qm) = 1161, respectively.

• The Journal of Advanced Prosthodontics
• /
• 제6권4호
• /
• pp.278-284
• /
• 2014

PURPOSE. There is insufficient data regarding the durability of porcelain laminate veneers bonded to existing composite fillings. The aim of the present study was to evaluate the fracture resistance and microleakage of porcelain laminate veneers bonded to teeth with existing composite fillings. MATERIALS AND METHODS. Thirty maxillary central incisors were divided into three groups (for each group, n=10): intact teeth (NP), teeth with class III composite fillings (C3) and teeth with class IV cavities (C4). Porcelain laminate veneers were made using IPS-Empress ceramic and bonded with Panavia F2 resin cement. The microleakage of all of the specimens was tested before and after cyclic loading ($1{\times}10^6$ cycles, 1.2 Hz). The fracture resistance values (N) were measured using a universal testing machine, and the mode of failure was also examined. The statistical analyses were performed using one-way ANOVA and Tukey post hoc tests (${\alpha}=.05$). RESULTS. There was a significant difference in the mean microleakage of group C4 compared with group NT (P=.013). There was no significant difference in the fracture loads among the groups. CONCLUSION. The microleakage and failure loads of porcelain laminate veneers bonded to intact teeth and teeth with standard class III composite fillings were not significantly different.