• Advances in concrete construction
• /
• v.5 no.3
• /
• pp.271-288
• /
• 2017

This paper aims to investigate the effects of replacing cement with ground granulated blast furnace slag (GGBFS) in self compacting concrete in the fresh and hardened state. The performance of SCC in moderate climate is well investigated but few studies are available on the effect of hot environment. In this paper, the effect of initial water-curing period and curing conditions on the performance of SCC is reported. Cement was substituted by GGBFS by weight at two different levels of substitution (15% and 25%). Concrete specimens were stored either in a standard environment (T=$20^{\circ}C$, RH=100%) or in the open air in North Africa during the summer period (T=35 to $40^{\circ}C$; R.H=50 to 60%) after an initial humid curing period of 0, 3, 7 or 28 days. Compressive strength at 28 and 90 days, capillary absorption, sorptivity, water permeability, porosity and chloride ion penetration were investigated. The results show that the viscosity and yield stress are decreased with increasing dosage of GGBFS. The importance of humid curing in hot climates in particular when GGBFS is used is also proved. The substitution of cement by GGBFS improves SCC durability at long term. The best performances were observed in concrete specimens with 25% GGBFS and for 28 days water curing.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2003.10a
• /
• pp.1-2
• /
• 2003

While aromatic polyimides and polyamides have found widespread use as high performance polymers, the present work addressed the need for organosoluble materials through the use of a hyperbranching scheme. The $AB_2$ monomers were prepared. The $AB_2$ monomers were then polymerized via aromatic fluoride-displacement and Yamazaki reactions to afford the corresponding hydroxyl-terminated hyperbranched polyimides (HT-PAEKI) and amine-terminated hyperbranched polyamides, respectively. HT-FAEKI was then functionalized with allyl and propargyl bromides as well as epichlorohydrin to afford allyl-terminated AT-PAEKI, propargyl-terminated PT-PAEKI, and epoxy (glycidyl)-terminated ET-PAEKI, in that order. All hyperbranched poly(ether-ketone-imide)s were soluble in common organic solvents. AT-PAEKI was blended with a bisphenol-A-based bismaleimide (BFA-BMI) in various weight ratios. Thermal, rheological, and mechanical properties of these blend systems were evaluated. Two characteristic hyperbranched polyamides, which the one has para-electron donating groups to the surface amine groups and the other has para-electron withdrawing groups to the surface amine groups, were selected to compare BMI curing behaviors. The electron rich polymer displayed ordinary Michael addition type exothermic reaction, while electron deficient polymer did display unusual curing behaviors. Based on analytical data, the later system provided the strong evidences to support room temperature curing of BMI by reactive intermediates instead of reactive primary amine groups on the macromolecule surface.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2003.05a
• /
• pp.19-22
• /
• 2003

The purpose of this study is to analyze the curing effect of planar surface heater for concreting in cold weather. Some experiments were conducted to evaluate the temperature history of concrete structures cured with heating sheets. Results are as follows ; (1) The temperature of concrete showed continuously rising trend with the heating by planar surface heater under the cold environmental condition of 3~-12$^{\circ}C$. And after about 24 hours the maximum temperature of concrete was reached at 25~3$0^{\circ}C$. (2) The temperature of slab concrete heated by planar surface heater of 130W/$m^2$ was at least $25^{\circ}C$ higher than that of an exterior air, and the curing performance was much more effective than heating by hot wind machine. (3) Through the curing by planar surface heater for 48 hours, the concrete maturity of about 1.5 times to heating by hot wind machine was acquired.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 1999.10c
• /
• pp.283-288
• /
• 1999

This study is performed to evaluate slump , air content, compressive strength and length change ratio of non-shrinkage high strength ocncrete is achieved by 10% expansive additive contained. The length change ration of non-shrinkage high strength concrete which is in water curing, shows 0.055% expansion in 10% expansive additive contained concrete and 0.308 expansion in 20% expansion additive contained concrete when it is curing 28 days.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05b
• /
• pp.469-472
• /
• 2006

Amount used of admixture fare is increasing for concrete economic efficiency and ability security. Security of economic efficiency and ability can expect by use of this admixture fare but is displaying a lot of problems on early age strength hold by hydrate delay relatively. Specially, in the case of construction site, concrete strength can speak that interrelation is high with mold removal of forms time. Therefore, is economical and need examination of plan that can secure robber within 3 days using admixture fare such as fly ash and blast furnace slage differential speech to secure function. In this study, adding liquid admixture within 1% of a binding agent quantity to examine these problem with physical characteristic after hardening ago specially, strength change at standard and air dry curing of observed change in priority. Air dried and water curing total strength enhancement effects appeared by thing which is in case of add test result liquid admixture by below 1% and strength deputy by passage of age could know is not big.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.11a
• /
• pp.549-552
• /
• 2004

This paper investigated the drying and autogenous shrinkage of high performance concrete(HPC) with mixture adjustment under various specimen size. For fresh concrete properties, HPC with mixture adjustment need a higher dosage of SP agent due to fluidity reduction, and a larger dosage of AE agent due to the reduction of air content. HPC with mixture adjustment exhibited a smaller strength development than control HPC. For drying shrinkage, an increase in specimen size occurred with small expansion during water curing and at air curing, less drying shrinkage was observed. Autogenous shrinkage was not affected by specimen size. Autogenous shrinkage of HPC with mixture adjustment exhibited less than half of control HPC.

• Journal of the Korea Concrete Institute
• /
• v.13 no.3
• /
• pp.277-284
• /
• 2001

Hardened concrete contains pores of varying types and sizes, and therefore the transport of air through concrete can be considered. The rate of permeability will not only depends on the continuity of pores, but also on the moisture contents in concrete and finishing material on concrete. Also it knows that the durability of reinforced concrete structure is concerned with air permeability which effects on the carbonation occurred by invasion of CO2 gas and the corrosion of steel bar occurred by O$_2$. In this paper, the effects of curing conditions and finishing materials on carbonation and air permeability are investigated according to the accelerated carbonation test. As results, carbonation velocity and air permeability are effected by curing conditions and finishing materials, and air permeability coefficient is effected by moisture content. Also the relationship between carbonation velocity coefficients and air permeability coefficients has been quite well established.

• Journal of Bio-Environment Control
• /
• v.20 no.4
• /
• pp.304-310
• /
• 2011

To evaluate the effect of curing treatment using a newly developed simplified curing unit (SCU) on the physicochemical quality of stored sweet potatoes was investigated for six months. The SCU consisting of a heater, an air circulation fan, exhaust fans, and a humidifying duct was installed in a cold storage room where the harvested sweet potatoes were stacked. During the six days of curing treatment, air temperature and relative humidity in the storage room were set at $32^{\circ}C$ and 90%, respectively. Physical and chemical properties of sweet potatoes were measured at 1-month intervals from the first day of storage. McKinney index showing the incidence and severity of decay was 0.83% in the curing treatment, while that of untreated control was 5.08% over the same storing period. Firmness, soluble solids content, and dry matter content in the cured sweet potatoes were greater than those of untreated control. Moreover, the changes of skin color in uncured potatoes occurred rapidly than cured one which showed delay of skin discoloration during the long-term storage. Results suggest that the SCU treatment improves the physicochemical quality of stored sweet potatoes and extends their storability. Therefore, the SCU can be effectively used for curing treatment of sweet potatoes with a relatively low cost.

• Journal of the Korea Institute of Building Construction
• /
• v.14 no.1
• /
• pp.61-67
• /
• 2014

As industry advances, the production of industrial sulfur is increasing every year. Therefore, this study intended to investigate the modified sulfur distribution and compressive strength characteristics of modified sulfur mortar based on the mixing method and curing conditions by adding modified sulfur with a melting point of approximately $65^{\circ}C$ in order to provide basic data for the application of the modified sulfur to the mortar or concrete. The results of the experiment showed that the mixture of fine aggregate and cement with water, followed by the addition of modified sulfur, would be most advantageous in terms of fluidity and strength. The results of EDS analysis also showed that the distribution of sulfur was the best. In terms of the curing conditions, the highest compressive strength was achieved through water curing and air dry curing at $20^{\circ}C$. However, it was found that the long-term strength was adversely affected by curing at over $40^{\circ}C$.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.21 no.1
• /
• pp.1-10
• /
• 2011

Generally, the tire curing process is the process in which the sulfur is added and subsequently the tire is heated to give the tire elasticity. In this process, all kinds of the chemicals in the tire are emitted with a lot of heat. The chemical fume and heat aggravate the work environment. To solve this problem, 92 local exhaust ventilators and 8 gravity ventilators were used, but not satisfactory yet. Preliminary survey showed that the temperatures in the process were very high: 30.3, 32.9 and $37.2^{\circ}C$ at 2, 4 and 6m above the ground level, respectively in the winter (outside temperature was $2^{\circ}C$). It can be imagined that the process is severely hot in the summer time. The higher temperature distribution in the higher space tells us that the hot plume could not be removed with the existing ventilation systems. Therefore, in this study, some alternative ventilation systems were designed. The partitions were used to contain the hot plume to increase the capture efficiency. The gravity ventilators were newly designed to improve the extraction efficiency of hot fume. To satisfy the balance of pressure in the curing process, some supply air system was introduced by renewing the existing air conditioning system. Many alternative solutions were evaluated by using computational fluid dynamics modelling. The best and applicable solution was selected and the existing ventilation system was modified. After implementing the new ventilation system, the hot environment was much improved. The temperature reduction in the curing process was about $6.4^{\circ}C$.