• Journal of the Korea Organic Resources Recycling Association
• /
• v.32 no.2
• /
• pp.15-25
• /
• 2024

In this study, the regeneration effect of pressurized water and ultrasonic cleaning was investigated for contaminated filter cloth from the sewage sludge filter press process. For this purpose, contaminated filter cloth was collected from a 3-ton sewage sludge hydrothermal carbon treatment filter press. First, the contamination characteristics were analyzed. According to the location of the filter cloth, air permeability and unit mass were measured, and compared with the values of a new filter cloth. Next, the results were mapped over the entire area to evaluate the contamination characteristics. Finally, pressure cleaning at 3 bar and ultrasound at frequencies of 34, 76, 120, and 168 kHz were performed on the contaminated filter cloth. In addition, the cleaning efficiency was evaluated by 3 levels of contamination degree. As a result, pore contamination occurred mainly at the bottom and both sides of the filter cloth, where the filter material was continuously injected and compressed. Surface contamination appeared evenly over the entire area. As a result of washing, air permeability increased by 1.3-3.1%p and contaminant removal was by 2.7-4.4% under pressure. In ultrasonic cleaning, air permeability increased by 12.5-61.5%p and contaminants were removed by 2.7-29.2%. In ultrasonic cleaning the lower the frequency, the higher air permeability and contaminant removal rate. Also, The higher pore contamination level, the better the air permeability improvement and contaminant removal.

• Journal of Environmental Science International
• /
• v.32 no.8
• /
• pp.555-561
• /
• 2023

A study is to predict the effective pulsing distance following to the pulsing pressure, nozzle diameter, filtration velocity using numercial analysis techniques and use it as an efficient operation condition and economic data for on-line type pulse air jet bag filter. Filtration area 6 m² condition, calculate filter resistance coefficient for simulation through the primary experiments using coke dust. For CFD simulation, analysis pulsing characteristics about nozzle diameter, filtration velocity and pulsing pressure. The maximum pulsing length of on-line type pulse air jet bag filter, in 10mm nozzle, filtration velocity 1.5m/min and pulsing pressure 5 bar conditions, is 2,285 mm, maximum length is 76.2% of the total filter bag, which is sufficient to pulsing. In 12mm nozzle, pulsing pressure 5 bar and filtration area 1.22 m² conditions, the maximum pulsing length of on-line type pulse air jet bag filter is 1,744~2,952 mm, and the maximum length is 2,952 mm indicates pulsing air can be reached to the bottom of filter bag. When the nozzle diameter is increased 8mm to 10mm, maximum pulsing length is extended 40~47%, and increased 10mm to 12 mm, maximum pulsing length is extended 10~17%. For effective pulsing, over the 5bar of pulsing pressure and larger than 10 mm of nozzle diameter are required.

• Applied Chemistry for Engineering
• /
• v.31 no.3
• /
• pp.338-340
• /
• 2020

Sericite is used as a raw material for ceramics and paints, and recently it is widely used as adsorbents to remove heavy metals in wastewater. A new air filter containing sericite was developed using the principle of which components contained in the sericite react with moisture in the air to release oxygen. We tested whether the newly developed air filter actually improves fuel efficiency when mounted on a diesel vehicle. When the diesel vehicle used in the test was warmed up, the fuel efficiency increased by 10~17% compared to when an existing air filter was installed. However, the effect of the developed air filter on the amount of emissions (HC, CO, NOx) has not been investigated, and further research is required for the diesel vehicle emissions.

• Particle and aerosol research
• /
• v.12 no.3
• /
• pp.73-80
• /
• 2016

Bioaerosol inactivation becomes important as people recognize the significance on the health effects of bioaerosols. There are several ways to inactivate such bioaerosols such as antimicrobial filters, UV, etc. For the on-filter-inactivation, proper antimicrobial materials coating should be applied. Recently, air ions are adopted to effectively reduce germ and virus activity. Limitations arise when each method is applied separately. Coating materials can experience chemical instability over time and temperature. Ionizers can generate ozone to prepare high ion concentrations. Combinations of developed techniques to enhance the inactivation efficiency were suggested. Researches on the air sterilization are reviewed and outlook is highlighted. Proper techniques such as combinations of filter material coating and air ion generation can be used to make air quality better for human living.

• Proceedings of the KIEE Conference
• /
• 2004.04a
• /
• pp.253-255
• /
• 2004

Conventional magnetic levitation systems could show unsatisfactory performance under air-gap disturbance due to rail irregularities. In this paper, we propose a feedback control system with discrete Kalman filter for air-gap disturbance attenuation. It is shown that excellent system performance can be obtained with the use of discrete Kalman filter, and that results from experiments agree well with those of simulations.

• ETRI Journal
• /
• v.25 no.2
• /
• pp.133-139
• /
• 2003

We studied how the passive intermodulation (PIM) power arising in air cavity filters could be calculated and how the design of the filter could be optimized in order to reduce the amplitude of the PIM signal. To do this, using simulated results, we optimized the various parameters of a filter. PIM in an air cavity filter depends on the power dissipated in its cavities. A reduction of this power loss therefore decreases the PIM power in the air cavity filter. Our experimental results confirm that it is possible to design and produce air cavity filters that generate low PIM signals.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.15 no.8
• /
• pp.619-629
• /
• 2003

A grease filter is used to remove grease generated from a cooking appliance in a kitchen. Since the inertial impaction is a dominant particle removal mechanism of the grease filter, the performance of the filter is greatly affected by the geometry. This numerical study has been conducted to investigate the effect of geometry on the performance of grease filters for four models having nominal flowrate of 100 m$^3$/h. Four models were designed by changing the shape of impaction surface, the length of eyelid, and the number of eyelids of the grease filter. The flow field and particle trajectories in the grease filter with a flow chamber were simulated using the commercial code of STAR-CD. The difference of air velocity and pressure distributions among four models was discussed in detail. The collection efficiency curves and the pressure drops of four models were also compared. It was found that the grease filter model with flat top surfaces shows highest performance among four models, having high particle collection efficiency and relatively low pressure drop. The cutoff diameter of this model representing 50-% collection efficiency is about 7.1 ${\mu}{\textrm}{m}$ for water droplets at 100 m$^3$/h.

• Journal of Korean Society for Atmospheric Environment
• /
• v.12 no.3
• /
• pp.279-287
• /
• 1996

Pressure drop and fractional collection efficiency of automotive cabin air filters were examined to obtain the basic data for the development of high performance domestic cabin air filters. Pressure drop of MA-V100 was higher than that of VF-V100, and it increased with the air flow rate. VF-V100 had longer time to rise the critical pressure drop than that MA-V100 had. Total collection efficiency of MA-V100 for initial and dust loaded conditions was higher than that of VF-V100. Also, fractional collection efficiency of MA-V100 for the fine particles was higher than that of VF-V100. Particla size distribution for the minimum collection efficiency ranged from 0.02 $\mu$m to 0.04 $\mu$m for MA-V100 and it ranged from 0.02 $\mu$m to 0.15 $\mu$m for VF-V100.

• Proceedings of the KSR Conference
• /
• 2008.06a
• /
• pp.2125-2129
• /
• 2008

This study was the development of air-cleaner for railroad passenger car. the characteristic of air-cleaner is to improvement of in door air quality and easy of maintenance. the air-cleaner is applicated to roll filter system. advantage of roll filter is to reduce time and cost of maintenance. The developed air-cleaner was installed to the railroad passenger car, and then has fieldtested for roll filter system's performance. the result of field-test performance was average Eff. 32% that is average of several days' measurement data.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.2
• /
• pp.106-111
• /
• 2018

In this work, we propose techniques for estimating the SOC of Li-air battery. First, we describe and explain the operation principle of the Li-air battery. Energy density of the Li-air battery was compared with that of the Li-ion battery. The capacity and impedance value of the fully discharged voltage is analyzed, and the OCV value for SOC estimation is measured through the electrochemical characterization of the Li-air battery. Estimation value is obtained by SOC modeling through extended Kaman filter and is compared with the measurement value from the Coulomb counting method. Moreover, the performance of SOC estimation circuit is evaluated.