• Land and Housing Review
• /
• v.5 no.4
• /
• pp.325-332
• /
• 2014

The purpose of this study was to measure the airtightness and Air-Flow Performance for 7th house of small apartment houses adopted window frame-type natural ventilation. All window and living room door is provide with window frame-type natural ventilation, and there is provide with manual controller. As the object of measurement, the 6th type small apartment houses with area of $33m^2$ to $51m^2$ was selected. airtightness performance was measured at the front door using Blower door system. We measured ventilation rate per hour on 50Pa pressure different between inside and outside by the 1st to 6th cases. As a result, when the natural ventilation frame was closed, average amounts are shown as the ventilation rate per hour were 2.27ACH (CASE1). and the result is similar to general apartment house (1.65~4.28ACH). When the natural ventilation frame was open, average amounts are shown as the ventilation rate per hour were 5.87ACH (CASE6). In addition, that's a 3.6ACH increased more than CASE1.

• Journal of Sensor Science and Technology
• /
• v.8 no.4
• /
• pp.341-346
• /
• 1999

In general cases, compared with glass electrode, FET type electrolyte sensors have many advantages. But the drift, memory effect and the poor reproducibility of the FET type electrolyte sensor cause the decrease of the reliability in the measurement system. To improve the reliability, an ion-measuring system using FET type electrolyte sensor array with 8 sensors has been developed. Developed system employed the electronic switchs to connect a signal detecting circuit with 8 sensor array and the system can measure ion concentration of 4 different type electrolyte($H^+$, $Na^+$, $K^+$, $Ca^{2+}$). The signal processing algorithm with insertion sorting method was adopted to enhance the reliability. We measured 3 different ion($H^+$, $Na^+$, $K^+$) to evaluate the performance of developed system. The results show that the designed signal processing algorithm can reduce the error range in comparison with a simple arithmetic mean and the developed system has a good reliability over the previous single channel sensor system.

• 한국지형공간정보학회:학술대회논문집
• /
• 2004.10a
• /
• pp.5-10
• /
• 2004

The purpose of this research is to measure a gravitational attraction about urban pulbic service facilities and to evaluate the location of public service facilities. It is important in that these facilities should provide more inexpensive and convenience public service to users. To do this, the GIS's spatial analysis and gravity model were used to analyze the efficiency of the public facilities. The gravity model was conducted as the main analysis method, and another model for this analysis was the discrete model. The gravity model is originally to anticipate migration flows, traffic flows and other types of movements so that this model compares the gravitational attraction between places. The discrete model is to find the optimal location and to evaluate a location of facility regarding urban areas as the combination of node and link. In this research, these two models were adopted to compare and analyze location of Mapo-Gu Office. The results of this research indicated that the locational evaluation of urban public service facilities discovered the appropriateness of those facilities, and the public facilities was necessary to displace to other site.

• Korean Journal of Construction Engineering and Management
• /
• v.10 no.3
• /
• pp.111-121
• /
• 2009

Value Engineering(VE) at design phase(so-called Design-VE) becomes quite a compulsory solution for better customer satisfaction, cost reduction, higher product performance, and, eventually, insured predominance in the competition. Unlike intended, however, the customer requirement on Design-VE has not been fully reflected in reality. Furthermore, the Design-VE occasionally does not progress in regular sequence; Preparation for measuring customer requirement - Function analysis - Idea creation. Therefore, this study suggests Axiomatic Design Theory to be adopted in Design-VE process expecting that the functions required by the customer could systematically reflected in VE process. Post-occupancy Evaluation(POE) is also represented as a method to measure and arrange the customer requirements. The customer satisfaction Design-VE process creates ideas defining functions in more detailed, to reflect the concrete user requirement. This approach helps function analysis and idea creation linked closely because function and idea are developed zigzag (i.e. function - idea - function...) in being decomposed into level down. The application of the process proposed by this study will be helpful to improve the customer requirement measurement and clarify a link between functions and ideas.

• Journal of The Korean Association For Science Education
• /
• v.33 no.7
• /
• pp.1471-1485
• /
• 2013

The purpose of this study was to develop a HAM (Heuristic Attention Model) by analyzing the difference between eye movements according to the science achievement of elementary school students on discrimination task. Science achievement was graded by the results of the Korea national achievement test conducted in 2012 for a random sampling of classes. As an assessment tool to check discrimination task, two discrimination measure problems from TSPS (Test of Science Process Skill, developed in 1994) which were suitable for an eye tracking system were adopted. The subjects of this study were 20 students from the sixth grade who agreed to participate in the research. SMI was used to collect EMD (eye movement data). Experiment 3.2 and BeGaze 3.2 programs were used to plan experiments and analyze EMD. As a result, eye movements of participants in discrimination tasks varied greatly in counts and duration of fixation, first fixation duration, and dwell time, according to students' science achievement and difficulty of the problems. By the analysis of EMD, strategies of the students' problem-solving could be found. During problem solving, subjects' eye movements were affected by visual attention; bottom-up attention, top-down attention and convert attention, and aflunter attention. In conclusion, HAM was developed, and it is believed to help in the development of a science learning program for underachievers.

• Parasites, Hosts and Diseases
• /
• v.34 no.1
• /
• pp.21-26
• /
• 1996

An experimental study was carried out to observe the effects of radiation on the infectivity of metacercariae of Gymnophalloines seoi to C3H mice. Oysters, the second intermediate host, were collected from an endemic area, and non-irradiated control, metacercaria-irradiation, and oyster-irradiation groups were prepared . One hundred metacercariae were infected orally to each mouse, and worm recovery rate was compared by groups at 7th day post-infection. In the metacercaria-irradiation group, the worm recovery rate was significantly reduced at radiation doses higher than 200 Gy, and the number of intrauterine eggs significantly reduced at doses over 50 Gy. In the oyster- irradiation group, 50 Gy significantly reduced both the worm recovery rate and number of uterine eggs. In the two groups, no worm was recovered at 1,000 Gy irradiation. Conclusively, irradiation of oysters with 200-1,000 Gy was effective to control infectivity of metacercariae to C3H mice, and could be adopted as a control measure for gymno-phalloidiasis.

• Journal of Korea Port Economic Association
• /
• v.30 no.2
• /
• pp.1-23
• /
• 2014

Although 'the International Ship Registration Act' has been enacted in Korea as of 1997, its effect is still in question to make shipowners and operators flag in or reflag because of insufficient incentives for them. Therefore, 'the Special Law for Jeju Free International City' has been established and the system of 'Special Ship Registration Zone' has also been enforced. Despite this, few studies were carried out to measure the relative importance of factors for Jeju International Ship Register yet. Against this backdrop, the purposes of this study are firstly, to investigate a relative importance of Jeju International Ship Registration System using AHP(Analytic Hierarchy Process) and secondly, to compare the characteristics of Flags of Convenience(FOC) with International Ship Register(ISR) which was adopted by several Far East Asia Countries(e.g., China, Hong Kong, Chinese Taipei and Japan). Moreover, this study aims to compare FOC with ISR in terms of shipping policy, ship management, and expenses and tax policy. In this paper, the factors were constructed with four high levels consisting of twenty one low levels to evaluate Jeju International Ship Register by utilizing Expert's brainstorming and AHP. According to the results, it is critical to expand the exemption and tax-related expenses, and also manage foreign-related systems systemically. This study provides important implications to maintain the tonnage tax system for ships effectively as well as to intensify the competitiveness of Jeju International Ship Register System.

• Journal of Korean Society of Forest Science
• /
• v.90 no.5
• /
• pp.650-662
• /
• 2001

The growth and yield models for five different kinds of natural forest types were systemically developed in the natural Broadleaved-Korean pine Forests in Northeast China. The data were collected from 359 temporary plots and 58 permanent plots with area ranged from 0.06 ha to 1.0 ha, ranging in stand age from 43 to 364 years. The Site Class Index (SCI) was introduced to evaluate site quality and the Crown Competition Factor (CCF) was selected as a measure of stand density for the mixed natural forest. The Chapman-Richards function was adopted to develop SCI equation and height-diameter curve. The Schumacher growth function was selected as base model to develop the DBH, basal area, and stand volume growth models by using re-parameterized method. In modeling mean DBH and basal area growth, it was found that the asymptotic parameter A of Schumacher function was exponentially related to site quality (SCI) and stand density (CCF). The rate parameter k was related to stand density and it was independent of SCI. Several validation measures for predicted stand variables were evaluated in the growth and yield models using independent data sets. The results indicated that relative mean errors (RME) in predicted stand attributes were less than ${\pm}5%$ and the estimated precision values of the stand variables were all greater than 95%.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.49 no.7
• /
• pp.1-9
• /
• 2012

In this paper, resistance temperature detector (RTD) integrated into the LED package is proposed in order to solve the temperature dependence of LED's optical properties. To measure the package temperature in real time, the RTD type temperature sensor having excellent accuracy and linearity between temperature change and resistance change was adopted. A stable metallic film is required for long term reliability and stability of the RTD type temperature sensor. Therefore, deposition and annealing condition for the film were determined. Based on the determined condition, the RTD type temperature sensor with the sensitivity of about $1.560{\Omega}/^{\circ}C$ was fabricated inside the LED package. In order to configurate the LED package system keeping the constant brightness regardless of the temperature, additional conversion circuit and control circuit boards were fabricated and added to the fabricated LED package. The proposed system was designed to compensate the light intensity caused by temperature change using the variable duty rate of driving current. As a result, the duty rate of PWM signal which is the output signal of the configurated system was changed with the temperature change, and the duty rate was similarly varied with the target duty rate. Consequently, it was focused the fabricated RTD can be used for compensating the optical properties of LED and the LED package which exhibits constant brightness regardless of the temperature change.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.5D
• /
• pp.483-492
• /
• 2012

The early setting time of concrete is an important factor determining the slip up velocity of the slip-form system. Accordingly, need is for a technique evaluating the early setting time in order to secure the safety of the slip-form system and the construction quality of concrete. This paper intends to estimate the early setting time by evaluating the setting degree of concrete using surface wave velocity so as to determine the slip up time of the slip-form system. Penetration resistance test and compressive strength test are performed first to clarify the relationship between the early setting time of concrete and the compressive strength. Then, compressive strength test and ultrasonic wave test are conducted to examine the relation between the compressive strength and the surface wave velocity. Continuous wavelet transform is adopted to measure the surface wave velocity. Numerical analysis is carried out to demonstrate the appropriateness of the application of continuous wavelet transform. Based on these results, the propagation velocity of the surface wave required for the slip up of slip-form system is suggested. Finally, a reduced model test of the slip-form system is conducted to verify the feasibility of the proposed surface wave velocity for the determination of th slip up velocity.