• 상하수도학회지
• /
• 제35권3호
• /
• pp.197-204
• /
• 2021

In MBR, extracellular polymeric substance (EPS) is known as an important factor of fouling; soluble EPS (sEPS) affects internal contamination of membrane, and bound EPS (bEPS) affects the formation of the cake layer. The production of EPS changes according to the composition of influent, which affects fouling characteristics. Therefore, in this study, the effects of the F/M ratio on the sEPS concentration, bEPS content, and fouling were evaluated. The effects of F/M ratio on the amount and composition of EPS were confirmed by setting conditions that were very low or higher than the general F/M ratio of MBR, and the fouling occurrence characteristics were evaluated by filtration resistance distribution. As a result, it was found that the sEPS increased significantly with the increase of the F/M ratio. When the substrate was depleted, bEPS content decreased because bEPS was hydrolyzed into BAP and seemed to be used as a substrate. In contrast, when the substrate is sufficient, UAP (utilization-associated products) was rapidly generated in proportion with the consumption of the substrate. UAP has a relatively higher Protein/Carbohydrate ratio (P/C ratio) than BAP, and this means, it has a higher adhesive force to the membrane surface. As a result, UAP seems like causing fouling rather than BAP (biomass-associated products). Therefore, R_f (Resistance of internal contamination) increased rapidly with the increase of UAP, and R_c (Resistance of cake layer) increased with the accumulation of bEPS in proportion, and as a result, the fouling interval was shortened. According to this study, a high F/M ratio leads to an increment in UAP generation and accumulation of bEPS, and by these UAP and bEPS, membrane fouling is promoted.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2222-2227
• /
• 2007

Newly structured metal-supported solid oxide fuel cell was fabricated and characterized by impedance analysis and galvanodynamic experiment. Using a cermet adhesive, thin ceramic layer composed of anode(Ni/YSZ) and electrolyte(YSZ) was joined with STS430 metal support of which flow channel was fabricated. $La_{0.8}Sr_{0.2}Co_{0.4}Mn_{0.6}O_3$ perovskite oxide was used as cathode material. Single cell performance was increased and saturated at operating time to 300hours at 800$^{\circ}C$ because of cathode sintering effect. The sintering effect was reinvestigated by half cell test and exchange current density was measured as 0.005A/$cm^2$. Maximum power density of the cell was 0.09W/$cm^2$ at 800$^{\circ}C$. Numerical analysis was carried out to classify main factors influencing the single cell performances. Compared to experimental IV curve, simulated curve based on experimental parameters such as exchange current density was in good agreement.

• 폴리머
• /
• 제32권4호
• /
• pp.313-321
• /
• 2008

UV개시에 의해 광경화형 아크릴 공중합체를 합성하고 제조된 아크릴 점착제(PSA)의 박리 에너지와 물리적 특성을 조사하였다. 이때 acrylic acid(AA)의 함량을 변화시켜 점착제의 물성을 변화시켰으며, 피착제의 표면 거칠기, 표면 요철방향, 점착제의 두께를 변화시킴으로써 박리 에너지의 변화 추이를 조사하였다. 공단량체인 acrylic acid의 함량이 증가함에 따라 표면 거칠기가 낮은 피착제가 높은 박리 에너지를 보였으며 점착제의 두께가 두꺼워 질수록 증가하였다. 또한 피착제 표면의 요철방향이 박리방향과 수평일 때 특히 높은 박리 에너지를 갖는 것으로 나타났다. 이것은 점착제의 두께 감소와 피착제 표면 거칠기의 증가가 wetting의 감소를 초래하지만 박리 시 저항력은 오히려 증가하는 경향을 나타내기 때문일 것이라는 예상과도 잘 일치한다.

• 대한기계학회논문집A
• /
• 제21권9호
• /
• pp.1357-1363
• /
• 1997

Currently it is increasing to use th bonded dissimilar materials in the various field of advanced engineering such as the highly rigid and lighter vehicle, plastic molding LSI package and metal/ceramic bonded joint. In spite of such a wide application of the bonded dissimilar materials, the evaluation method of the bonding strength has not been established yet. Therefore in this paper we analyze the interface crack problem by introducing fracture mechanics parameters as the basic research about estimating of the strength of adhesive joints. The variation of stress intensity factor according to the elastic modulus of adherend and thickness of bonded layer are investigated. Numerical results are based on the results of boundary element analysis of four different type butt joints subjected to uniaxial tension loading.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2001년도 The IMAPS-Korea Workshop 2001 Emerging Technology on packaging
• /
• pp.100-103
• /
• 2001

본 연구에서는 무전해도금으로 증착된 구리박막의 열적 및 접착특성에 관하여 고찰하였다. Si 기판에 MOCVD 방법으로 TaN 확산방지막을 증착한 후, 무전해 도금으로 구리박막을 증착하여 Cu/TaN/Si 다층구조를 제조공정하였다. 그리고, Ar 분위기에서 열처리시켰으며, 열처리온도에 따른 비저항 변화를 고찰함으로서 Cu/TaN/Si 계의 열적 특성을 분석하였다. 무전해도금 구리박막의 접착특성은 스크래치 테스트에 의해 평가하였으며, 열적 증착방법과 스퍼터 방법으로 증착된 구리 박막과 비교하였다. 스크래치 테스트 결과, 무전해도금 구리 박막의 접착력이 열적 증착과 스퍼터 방법으로 증착된 구리 박막보다 더 우수하였다.

• 대한기계학회논문집A
• /
• 제25권1호
• /
• pp.115-126
• /
• 2001

In this paper, through a series of comparative experiments, effects of two different cure processing methods, cocure and precure, on the mechanical properties of honeycomb core materials for aircraft applications are considered. Mass of moisture accumulated into the closed cells of the sandwich panel specimen from the measured mass of moisture diffused to the full saturation state into the elements(skin, adhesive layer, Nomex honeycomb), consisting the honeycomb sandwich specimen has been calculated. Water reservoir of 70$\^{C}$ was used to have specimens absorb moisture to see the influence of moisture absorbed into sandwich panel on its mechanical properties. For the repair condition holding for 2 hours at 177$\^{C}$(350℉) temperature, a pressure due to the vapor expansion in each cell of the sandwich panel, which may result in the local separation of the interface between laminated skin and the surface of the honeycomb, has been estimated by vapor pressure-temperature relation from the thermodynamic steam table and compared to the pressure from the ideal gas state equation. The bonding strengths of the laminated skins on the flat surface of the Nomex honeycomb have been compared by the flatwise tension test and climbing drum peel test performed at room temperature for dry, wet and wet-repair specimens, respectively.

• Applied Microscopy
• /
• 제43권1호
• /
• pp.14-20
• /
• 2013

The leopard danio, Danio rerio var. frankei is a spotted color morph of the zebrafish, Danio rerio caused by a pigment mutation. The structural differences of fertilized egg and egg envelope are poorly documented. To clarify this, we compared the fertilized egg morphology and ultrastructures of surface structures, the micropyle and the cross section of fertilized egg envelopes of zebrafish and leopard danio, variation species of zebrafish using a light and electron microscopes. Although the fertilized egg sizes were different, the external shapes of the fertilized eggs of two species couldn't be differentiated under the light microscope. The characteristics of fertilized eggs, such as a spherical shape, a non-adhesive quality and a large perivitelline space, were shown to be related to spawning habit. In ultrastructure of fertilized egg envelope, there is no morphological difference of micropyle between two species. By contrast, the ultrastructure and the numbers of knob-like structures and semihemisphere-like structures per unit area on the outer surface, and the number of lamellae of inner layer on the fertilized egg envelope section displayed definite species specificity. Collectively, our data indicate that the ultrastructure of fertilized egg envelope in the zebrafish could be differentiated by species variation.

• 박물관보존과학
• /
• 제9권
• /
• pp.67-83
• /
• 2008

국립중앙박물관이 소장하고 있는 청연군주 출토복식(신수751 의류 일괄) 중 織金 및 金箔이 있는 복식의 보존 처리 과정을 소개하고자 한다. 금사 및 금박의 비파괴분석(X-선형광분석:XRF)을 실시한 다음 표면의 금(Au)이 열화가 진행되면서 분상화된 금층에 아교 2%용액을 도포하여 접착력을 강화하였다. 표면의 먼지와 오염물제거를 위해 진공흡입을 통한 건식세척과 분사식 습식세척을 병행하였고 손상부분을 보수하여 유물의 원형을 회복하였다.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2000년도 추계학술대회논문집
• /
• pp.116-119
• /
• 2000

The advantage of plasma-sprayed coating is their good resistance against thermal shock due to the porous state of the coated layer with a consequently low Youngs modulus. However, the existence of many pores with a bimodal distribution and a laminar structure in the coating reduces coating strength and oxidation protection of the base metals. In order to counteract these problems, there have been many efforts to obtain dense coatings by spraying under low pressure or vacuum and by controlling particle size and morphology of the spraying materials. The aim of the present study is to survey the effects of the HIP treatment between 1100 and 130$0^{\circ}C$ on plasma-sprayed oxide coating of A1$_2$O$_3$, A1$_2$O$_3$-SiO$_2$on the metal substrate (type C18N10T stainless steel). These effects were characterized by phase identification, Vickers hardness measurement, and tensile test before and after HIPing. These results show that high-pressure treatment has an advantage for improving adhesive strength and Vickers hardness of plasma-sprayed coatings.

• Structural Monitoring and Maintenance
• /
• 제7권3호
• /
• pp.233-259
• /
• 2020

Using bonded fiber-reinforced polymer laminates for strengthening wooden structural members has been shown to be an effective and economical method. In this research, properties of suitable composite materials (sika wrap), adhesives and two ways of strengthening beams exposed to bending moment are presented. Passive or slack reinforcement is one way of strengthening. The most effective way of such a strengthening was to place reinforcement laminates in the stretched part of the wooden beam (lower part in our case), in order to investigate the effectiveness of externally bonding FRP to their soffits. The model is based on equilibrium and deformations compatibility requirements in and all parts of the strengthened beam, i.e., the wooden beam, the sika wrap composite plate and the adhesive layer. The theoretical predictions are compared with other existing solutions. This research is helpful for the understanding on mechanical behaviour of the interface and design of the composite-wooden hybrid structures. The results showed that the use of the new strengthening system enhances the performance of the wooden beam when compared with the traditional strengthening system.