• Journal of the Korean Institute of Intelligent Systems
• /
• v.15 no.2
• /
• pp.179-184
• /
• 2005

An accurate evaluation of a production capacity is an important role for production planning in manufacturing industry. The study has been partly done about the fluctuation in the conventional study of the production capacity, but the study of the subordination has been hardly done. Therefore, in this paper, we will devide by the production capacity which is formed into the production subjects to evaluate objectively the differences of between the actual capacity and the designed capacity in manufacturing industry and will suggest production capacity estimation model which is considered the fluctuation and the subordination, the decreasing causes of the production capacity. The weight of fluctuation which is used for the computation of the ratio of fluctuation and the ratio of subordination and the subordination are denoted to the interval number Thus, the production capacity is denoted to the interval numbers. The efficiency of the proposed model will show through the case study.

• The Journal of Korean Association of Computer Education
• /
• v.7 no.1
• /
• pp.79-88
• /
• 2004

Since computer integrated technology was introduced to the field of education, it has offered an expanding range of interactive possibilities which are remarkably powerful and helpful for the learners, especially constructing the cyber learning environments. Interactivity, the critical element in cyber learning, is categorized into three dimensions: student-to-contents, student-to-student and student-to-instructors. Six surrogate variables are introduced, and two quantitative model are developed for evaluating the degree of interactivity. The first model, which is called Data Envelopment Analysis model, is a linear programming based technique for measuring the relative performance of organizational units where the presence of multiple inputs and outputs makes comparison difficult. DEA model allows each unit to adopt a set of weight that shows it in the most favorable light in comparison to the other unit. The Second model employes the weighted average of standardized input variables for evaluation. Actual data have been collected from the Cyber IT university and these two models are applied for comparison. The analysis shows that the results from these two models are very much similar to each other, and are highly correlated to the level of class satisfaction.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.13 no.4
• /
• pp.123-129
• /
• 1993

Because the existing scour prediction formulas for plunge pools of pipe culverts and spillways give a wide range of predicted scour depths, it is difficult to estimate actual scour depths. A review of literature showed that wide range of predicted values was caused mostly by lack of thorough analysis of the scour mechanism. In this study, the effects of the parameters govering scour were examined, and the scour potentials were measured. The major variables govering scour were the velocity and size of jet impinging into the plunge pool, the submerged weight of bed material, the ratio of jet size to bed material size, the tail watr depth of the plunge pool, and the angle of jet impact on water surface. The ratio of jet size to bed material size to bed material size was found to be another significant parameter affecting scour for larger bed materials. A densimetric Froude nember of the bed material in incipient motion was formulated. This number represented the scour potential of the jet at the point where the bed material was tested.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.39 no.6
• /
• pp.454-459
• /
• 2006

A simultaneous high-performance liquid chromatography assay method for amoxicillin and ampicillin in fish products was developed, evaluated, and validated by monitoring these antibiotics in fish samples obtained from aquaculture and distribution. The recovery rate of this method was higher than those of conventional methods and was 95.3-106.6% for amoxicillin and 81.4-92.4% for ampicillin. Our pretreatment procedure sufficiently removed or reduced materials affecting HPLC analysis, such as low-molecular-weight substances. The performance limit of this method was evaluated as 0.01 ppm of amoxicillin and ampicillin in fish muscle. Finally, 171 fish samples, including olive flounder (Paralichthys olivaceus), common sea bass (Lateolabrax japonicus), and black rock fish (Sebastes schlegeli) collected from fish farms in the coastal area between April and September 2005 were analyzed to evaluate the overall efficiency of the method and to monitor the actual of amoxicillin and ampicillin usage in fish farms. The results indicated that the developed method was suitable for analyzing amoxicillin and ampicillin in fish muscle, and determined that those antibiotics were being used for fish farming but were not detected in fish samples during the shipping and distribution stages.

• Fashion & Textile Research Journal
• /
• v.3 no.1
• /
• pp.70-80
• /
• 2001

This study was designed to investigate actual conditions of textile design education at technical high school in Korea, and to present possible solutions for improving its effectiveness. Inchon Girl's Polytechnic high School was selected as sample of case study because it was the only school which has textile design major. Survey was done through questionnaire and telephone interview. 100 students, 25 graduates, 8 teachers, and 8 managers of textile industry were involved in survey. The data were analyzed by using frequency, t-test, correlation. Statistical analysis resulted in the following suggestions to be considered for maximizing the effectiveness of the textile design education at technical high schools: First, the curriculum should be flexibly reorganized to come up with trends in the market and demands from industry, and also to stimulate and motivate students into the biggest achievements possible. Second, more weight should be given to practical design subjects which have proved to be preferred by students and industry by reducing class hours for non-design subjects or theoretical subjects. Third, equipments and facilities for practical exercise should be open to students anytime needed so that students can improve their practical skills without any restrictions. Fourth, new teachers having majored in textile design at the university should be employed and the existing teachers should be periodically re-educated to keep abreast with new knowledges and technology. Fifth, The solidarity and the connection between schools and companies should be reinforced, not only to provide graduates with more chances to get a job, but also to make education at schools refreshed and updated.

• Journal of Advanced Marine Engineering and Technology
• /
• v.18 no.1
• /
• pp.114-122
• /
• 1994

A cold temperature control system for the BAF(batch annealing furnace) has been established in order to reduce energy consumption to imrpove productivity and stabilize the properties of products. Therefore we confirmed a relation between annealing cycle time and atmospheric gas, changing annealing cycle time according to BAF temperature with time during heating and actual temperature measurements cold spot during soaking. The results of the temperature variation effect on the batch annealing are as follows. 1) Cooling rate is increasing gradually with increasing atmospheric gas flow, but heating rate is hardly increasing without atmospheric gas component. Heating time is reduced to one half with increasing atmospheric gas flow rate and changing of atmospheric gas component from HNx to Ax gas and annealing cycle time is reduce to 2.7 times. 2) With enlarging the difference between furnace temperature and soaking temperature at the HNx BAF, heating time becomes short, but cooling time is indifferent. 3) If temperature difference of 300.deg. C in the temperature change of cold spot according to the annealing cycle control temperature, Hi-CON/H2BAF is interchanging at each other at 26hours, but HNxBAF at 50 hours. 4) Soaking time at batch annealing cycle determination is made a decision by the input coil width, and soaking time for quality homogenization of 1219 mm width coil must be 2.5 hours longer then that of 914mm width coil for the same coil weight at Hi-CON/H2BAF. But, it is necessary to make 2 hours longer at HNxBAF.

• Journal of Preventive Medicine and Public Health
• /
• v.7 no.2
• /
• pp.395-401
• /
• 1974

In order to figure out the normal range, lower limit of hypertension and upper limit of hypotension of the blood pressure of Korean, authors had measured blood pressure according to Korotkow's method for 31,897 healthy persons as samples who were occupied different levels of the social class except cases who would seem to be the essential hypertension and had the diseases affecting to secondary hypertension. A following conclusion was induced by actual measurement and statistical reasoning. 1. The normal range and limits of hypo- and hypertension by sex and age groups of Korean were demonstrated in Table 1 and Figure 1. 2. The more aging the higher value of blood pressure in both sexes, especially women rather than men and systolic as to diastolic. 3. Generally, blood pressure values of female were lower than male, after 55 years of age, however, the crossing phenomenon was recognizable. 4. To settle the normal and abnormal ranges of the blood pressure of Korean, it was attempted that $M{\pm}1.282{\sigma}$ as normal range, $M+2{\sigma}$ as lower limit of hypertension and $M-2{\sigma}$ as upper limit of hypotension were calculated, and regression lines were drawn to adjust the biological variables and derive continuity from each age class. (Fig. 2 and 3) 5. The blood pressure levels were becoming elevated as to getting increased of the body weight, particularly diastolic value at 40-49 age group in male and systolic value at 30-39 age group in female.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.5
• /
• pp.115-122
• /
• 2012

Automobile collision analysis is composed of various shapes, and the speed variation working to the vehicle during collision are utilized as a very important factor in evaluating the degree of vehicle collision or passenger safety. So, the method of analyzing result values on the speed variation utilizing collision analysis program become necessary. This study utilized PC-Crash program in order to compare actual values and analyzed values of braking distance with the friction coefficient of road surface according to vehicle velocity. As a result, the smaller friction coefficient found to be larger error, and the maximum error range of collision velocity in case of each different vehicles (MATIZ, SONATA, or BUS) at the intersection showed 1.2%, 1.8%, 3.1% according to the difference of vehicle weight. Moreover, an accidental fall at IN-CHEON large bridge in order to reappear was verified with practicing simulation which has a slight error.

• Journal of the Korea Society of Computer and Information
• /
• v.24 no.12
• /
• pp.101-108
• /
• 2019

The purpose of this study was to investigate the subjective evaluation and the characteristics of each type of maternal self-awareness. It was to provide the basic data necessary for the development of clothing that can improve the satisfaction of the body shape of pregnant women. This study was conducted with Q methodology, and was performed for pregnant women over 6 months. Analysis was done with QUANL program. The recognition types of body shape of pregnant women was analyzed as three types: thin limbs and central hemispherical abdominal body shape, under abdomen protruding body shape, and thick upper arm and central abdomen protruding body shape. The thin limbs and central hemispherical abdominal body shape were considered to be normal, with the lowest BMI index before pregnancy. And the limbs were thin and the other parts were not overweight, but recognized that only the belly came out. The under abdomen protruding body shape was overweight with the highest BMI index before pregnancy. In addition to the circumference of the chest and hips, the body was gaining weight and was perceived to have a belly drooping down. The thick upper arm and central abdomen protruding body shape recognized that the middle part of the abdomen protruded like the first type, but it was different from the first type because the upper arm was thickened. In the future study, it would be a meaningful study to compare and analyze the difference with the recognition body of this study through analyzing the actual body shape of pregnant women.

• Journal of Korean society of Dental Hygiene
• /
• v.12 no.3
• /
• pp.553-562
• /
• 2012

Objectives : The purpose of this study was to examine actual conditions of smoking and alcohol drinking behaviors among high school students, so that it could recognize possible harmful effects of smoking on oral health and could give positive motivations for students to quit smoking and drinking. Methods : This research was based on self-filling survey which 1,385 high school students in metropolitan area in Korea from September 5 to October 28, 2011. Surveyed data were analyzed by descriptive statistics, ${\chi}^2$-test and logistic analysis using SPSS WIN 12.0 program and its signification level was 0.05. Results : 1. As for smoking rate and drinking rate, boy students accounted for 11.6% and 25.4%, thereby having been higher than girl students(p<.001). It was the highest in over 180 cm(16.0%, 35.0%, p<.001) for height, in 60-under 70 kg for weight(13.4%, 23.5%, p<.001), and in a case of profession for mother's job(13.8%, 28.4%, p<.005). 2. The perceived oral symptoms had relationship with the less than 10 cigarettes of smoke (OR=2.41; 95% CI:1.31-4.41), more than 11 cigarettes of smoke (OR=3.16; 95% CI:1.42-7.00) and more than 1 bottle of alcohol (OR=1.75; 95% CI:1.00-3.06). Conclusions : This result implies that adolescents' smoking and drinking have correlation with oral health status, which makes uncomfortable sense felt given chewing along with the pain in teeth and gum. Based on the above findings, a school or community needs to reinforce education for preventing smoking and drinking and to offer environment available for practicing anti-smoking and anti-drinking plan, in order to reduce adolescents' smoking and drinking.