• 보존과학회지
• /
• 제28권4호
• /
• pp.387-394
• /
• 2012

전문적인 보존시설이 없는 대부분의 도서관에서는 손상된 도서의 간단한 수선 처리 및 응급조치 시 일반시판용 합성수지 접착제를 사용하고 있고, 이는 크게 PVAc 계열(Pa), 아크릴 계열(Ac)과 PVP 계열(Pv)로 나눠진다. 국립중앙도서관 자료보존실에서 사용하고 있는 보존용 합성수지 접착제(Pa-1)와 일반시판용 합성수지 접착제 중 대표적인 접착제를 골라 열화특성을 연구하기 위해 인공열화를 진행한 뒤, 약 한 달 동안 산성도(pH)와 색도를 측정하였다. 산성도 실험 결과에서 Pa-1(pH 7~7.5)과 Ac-2(pH 6.5~8)는 보존처리에 적합한 범위를 나타내었다. 색도실험에서 황변도를 나타내는 ${\Delta}b^*$는 Pa-1

• 대한기계학회논문집A
• /
• 제24권10호
• /
• pp.2405-2412
• /
• 2000

A cast stainless steel may experience an embrittlement when it is exposed to approximately 30$0^{\circ}C$ for long period. In the present investigation, The three classes of the thermally aged CF8M specimie n are prepared using an artificially accelerated aging method. Namely, after the specimen are held for 300, 1800 and 3600hrs. at 43$0^{\circ}C$ respectively, the specimens are quenched in water to room temperature. Load versus load line displacement curves and J-R curves are obtained using the unloading compliance method. $J_{IC}$ values are obtained following ASTM E 813-87 and ASTM E 813-81 methods. In addition to these methods, JIC values are obtained using SZW(stretch zone width) method described in JSME S 001-1981. The results of the unloading compliance method are $J_Q$=485.7 kJ/m$^2$ for virgin material, $J_{IC}$ of the degraded materials associated with 300, 1800 and 3600hrs are obtained 369.25 kJ/m$^2$, 311.02 kJ/m$^2$, 276.7 kJ/m$^2$, respectively. The results of SZW method are similar to those of the unloading compliance method. Through the elastic-plastic fracture toughness test, it is found that the value of $J_{IC}$ is decreased with increasing of the aging time. The results obtained through the investigation can provide reference data for a leak before break(LBB) of reactor coolant system of nuclear power plants.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 C
• /
• pp.1676-1678
• /
• 2004

Class-F resin-rich type insulating tapes are generally used for the groundwall insulations of the large turbine generators with air-cooled and hydrogen-cooled stator windings. In this paper, mechanical strength properties degraded over aging time in higher temperature than designed one in normal condition were experimentally investigated and the results of comparative tests were presented on the existing class-F resin-rich type tape and a developed one after curing. The resin-rich insulating tapes with composite material of Mica/Epoxy/support currently were used in this test. The tests for tensile and flexural strength properties were conducted with the specimens which were composed of unaged and the aged specimens accelerated for one, two, and three thousand hours at 180 $^{\circ}C$. The tensional strength was only measured for the unaged specimens and the results are also presented to make a comparative test for their initial mechanical characteristics.

• 임산에너지
• /
• 제21권2호
• /
• pp.34-42
• /
• 2002

천연물계의 유지를 목재에 처리하여 발수성능을 평가하였다. 시험에 사용한 유지는 아마인유, 피마자유, 올리브유, 콩기름, 들기름, 해바라기 씨 기름이다. 발수성 평가는 흡습성, 흡수성 시험과 접촉각 시험으로 하였다. 발수 처리한 목재를 빛과 수분에 의해 촉진열화 시킨 후에 열화정도를 색차계로 측정하였다. 촉진열화된 처리목재의 발수성능을 흡수성시험과 접촉각 시험을 통하여 비교 측정 하였다. 흡습성 시험결과, 흡습 초기에는 무처리에비하여 흡습량이 적으나 흡습처리 시간이 증가할수록 무처리의 흡습량에 가까워져 48시간 흡습처리 후에는 흡습비의 큰 차이는 없었다. 접촉각 시험의 결과, 처리재와 무처리재간의 결과가 큰 차이를 나타내었다. 유지의 농도와 종류에 따른 접촉각 변화는 흡습성 시험과 같이 큰 차이는 나타나지 않았다. 천연유지의 발수성능으로는 기상열화에 대한 안정성이 낮았다. 천연오일 단독처리만으로는 광열화에 대한 안정성을 기대하기 어려웠다.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제52권8호
• /
• pp.348-353
• /
• 2003

This paper was the research of high voltage suspension insulator (400 [kN]) including pottery stone, feldspar, clay and alumina of 17 [wt%]. The slurry was fabricated after ball milling mixed raw materials. Green compacts were made by the extrusion of jiggering method and were sintered at 1300[$^{\circ}C$] for 50 [min.] in the tunnel kiln. The sintered density was reached to 97% of theoretical density, and the bending strength was 1658 [k $g_{f}$/$\textrm{cm}^2$] and hardness and fracture toughness which was measured by ICL( indentation crack length ) method were 1658 (kgf/$\textrm{cm}^2$) and 27.5 [Gpa], respectively. In measurement of tana and insulation break voltage of 400 (kN) porcelain, tan$\delta$ took some numerical value between 17${\times}$10$_{-3}$ and 61${\times}$10$_{-3}$ and insulation break voltage value was 19.9$\pm$1.4 [㎸/mm]. The test was performed to research whether the shape of pin affect a overvoltage break load or not As a consequence, when a pin was designed a pin diameter 51 [mm] with the bottom form of two-step constructed with straight in the suspension insulator, Insulator showed overvoltage break load 52 [ton] of the highest value and reflected a fine characteristic in aged deterioration test which is one of the accelerated aging test. Also it could be confirmed a fine characteristic through performing the test that electrical property of insulator was established correctly in accordance with IEC 60383-1 standards.s.

• Elastomers and Composites
• /
• 제47권1호
• /
• pp.9-17
• /
• 2012

본 연구에서는 클로로프렌 고무의 열 및 해수에 의한 노화 현상에 따른 물성 변화 및 사용 수명을 예측하였다. 가속 스트레스 수준은 열노화 $80^{\circ}C$, $100^{\circ}C$, $120^{\circ}C$, 해수침지노화 $40^{\circ}C$, $60^{\circ}C$, $80^{\circ}C$에서 2년 3개월(20,000Hr)동안 가속노화를 통해 인장시험을 수행하여 신장률, 인장강도, 경도를 통한 물성변화 측정을 하였다. 분석 결과신장율 저하가 가장 주된 고장지배모드임을 알 수 있었다. 아레누이스 식을 이용한 노화수명 예측 결과 열노화된 CR의 예측 수명은 $23^{\circ}C$에서 125년이며, 해수침지노화된 CR의 예측수명은 $23^{\circ}C$에서 9년이었다. SEM과 SEMEDS 분석 결과, 해수노화시편이 균열과 SEM-EDS에서는 산소의 농도가 증가하였으며, 이를 바탕으로 FT-IR에서는 해수와의 반응에 의하여 C-O와 C=O 결합이 생성되었음을 관찰하였다. 또한 DSC와 TGA 분석에서는 해수침지노화에 의하여 유리전이온도가 상승하며 분해온도가 낮아짐을 관찰하였다.

• Current Photovoltaic Research
• /
• 제8권4호
• /
• pp.114-119
• /
• 2020

In this study, Mitigation of Potential-induced degradation (PID) for PERC solar cells using SiO2 Structure of ARC layer. The conventional PID test was conducted with a cell-level test based on the IEC-62804 test standard, but a copper PID test device was manufactured to increase the PID detection rate. The accelerated aging test was conducted by maintaining 96 hours with a potential difference of 1000 V at a temperature of 60℃. As a result, the PERC solar cell of SiO2-Free ARC structure decreased 22.11% compared to the initial efficiency, and the PERC solar cell of the Upper-SiO2 ARC structure decreased 30.78% of the initial efficiency and the PID reliability was not good. However, the PERC solar cell with the lower-SiO2 ARC structure reduced only 2.44%, effectively mitigating the degradation of PID. Na+ ions in the cover glass generate PID on the surface of the PERC solar cell. In order to prevent PID, the structure of SiNx and SiO2 thin films of the ARC layer is important. SiO2 thin film must be deposited on bottom of ARC layer and the surface of the PERC solar cell N-type emitter to prevent surface recombination and stacking fault defects of the PERC solar cell and mitigated PID degradation.

• The Journal of Advanced Prosthodontics
• /
• 제10권1호
• /
• pp.50-57
• /
• 2018

PURPOSE. To investigate the effect of accelerated aging on surface properties of glazed CAD/CAM resin blocks using a 2D surface profilometer and a 3D non-contact optical profilometer. MATERIALS AND METHODS. Three types of CAD/CAM resin restorative materials, LAVA Ultimate (3M ESPE, St Paul, MN, USA), VITA Enamic (Vita Zahnfabrik H. Rauter, Bad $S\ddot{a}ckingen$, Germany), and Cerasmart (GC Corparation, Tokyo, Japan) were used for this study. CAD/CAM blocks were cut in 3-mm thickness slabs and divided into three groups; Group 1: control group (specimens polished with 600 grit SCI paper); Group 2: specimens sandblasted, silanized, and glazed with Optiglaze Color (GC); Group 3: glazed specimens subjected to 5000 thermocycles (n=15). The surface roughness ($R_a$ and $R_z$) was evaluated using a profilometer and a 3D scanning instrument. Data were analyzed using two-way ANOVA and Tukey's post- hoc test (P<.05). RESULTS. LAVA, VITA, and Cerasmart exhibited statistically similar $R_a$ and $R_z$ values for each group (P>.05). For VITA and Cerasmart, the specimens in Group 1 exhibited significantly higher $R_a$ values than Group 2 (P<.05). Group 1 ($0.502R_a$), Group 2 ($0.384R_a$), and Group 3 ($0.431R_a$) exhibited statistically similar $R_a$ values for LAVA (P=.062). After 5000 thermocycles, surface roughness values did not change significantly for glazed LAVA, VITA, and Cerasmart (P>.05). CONCLUSION. Glaze material Optiglaze Color makes CAD/CAM resin surfaces smooth and glazed CAD/CAM surfaces seem resistant to deterioration under 5000 thermocycles.

• 전기학회논문지
• /
• 제60권6호
• /
• pp.1163-1168
• /
• 2011

Most transformers use insulating and cooling fluids derived from petroleum crude oil, but mineral oil has some possibility of environmental pollution and fire with explosion. vegetable oil fluids extracted from seed has superior biodegradation and fire-resistant properties including an exceptionally high fire point enhancing fire safety. In this study, it is aimed at the practicality of substituting natural ester dielectric fluid for mineral oil in liquid insulation system of transformers. As a rise in coil winding temperature has a direct influence on transformer life time, it is important to evaluate the temperature rise of coil winding in vegetable oil in comparison with mineral oil. Four transformers for the test are designed with 10KVA, 13.2KV, one phase unit. The temperature are directly measured in insulating oil of these transformers with the two sorts of natural ester and mineral oil dielectric fluid respectively. Experiment for aging carry out two means. First means remained $120^{\circ}C$ that transformer of mineral oil were operated at 185% load. Second means is that insulating oils of two natural ester and mineral oil were aged by thermal cycles repeating from $30^{\circ}C$ to $120^{\circ}C$. For the heating, Transformers were operated at 185% load. For the cooling, cooling system was operated in the chamber. Samples were analyzed at 42, 63, 93, 143, 190, 240 300cycles. Analysis contents are dielectric strength, total acid value. Mineral oils compared results of first means with results of second means. And compared two sort natural esters respectively with mineral oil in second means.

• Applied Microscopy
• /
• 제43권4호
• /
• pp.164-172
• /
• 2013

In this work, microstructural and hardness evolution of the X20 steel upon short-term creep test ($550^{\circ}C$ to $650^{\circ}C$, $180^{\circ}C$ to 60 MPa) was studied by using scanning electron microscope, electron backscattered diffraction, and transmission electron microscope, microhardness tester. After creep rupture, gauge and grip part of the specimens were microstructurally analyzed. Creep at the $650^{\circ}C$/60 MPa resulted in a rupture at 1,460 hours with growth of lath width from 1.31 to $2.87{\mu}m$ and a grain growth with a more equiaxed feature. There is a close relationship between Microhardness and lath width. The formation and coarsening of Laves phase, which was observed up to $600^{\circ}C$ of creep temperature, was accelerated by the applied stress. Slight coarsening of the $M_{23}C_6$ was observed in the $550^{\circ}C$ and $600^{\circ}C$ crept or aged specimens. The coarsening of $M_{23}C_6$ depended on the temperature, where specimens crept at $650^{\circ}C$ showed higher growth rate. The microstructural evolution of X20 after short-term creep test was extensively discussed in relation to the long-term creep/aging test reported in literatures.