• 한국음향학회지
• /
• 제32권4호
• /
• pp.346-353
• /
• 2013

본 논문에서는 노래반주기를 위한 고음질 오디오 시스템 구현에 관한 내용을 담고 있다. 노래반주기의 중요한 기능인 키/템포 변환 음질의 개선을 위하여 악기별 채널 분리를 수행하였다. 악기별로 채널을 분리하여 처리함으로 고음질의 변환이 수행됨을 상관계수의 변화와 MOS 평가를 통하여 확인할 수 있었다. 구현된 오디오 시스템은 TI사의 32비트 부동 소수점과 고정 소수점 연산이 모두 가능한 DSP인 TMS320C6747를 이용하였으며 다채널의 WMA 복호화, MP3 부호화와 복호화, wav, EQ 및 템포/키 변환을 실시간으로 수행 가능하다. WMA 10채널로 구성되어 악기별 분리 처리가 가능도록 하였다. 또한 MP3 부호화/복호화는 녹음과 재생 기능으로 이용되고 wav 채널은 효과음 등으로 사용 가능하다.

• 한국전기전자재료학회논문지
• /
• 제14권6호
• /
• pp.455-459
• /
• 2001

In this paper, the dielectric and pizoelectric properties of 0.05Pb(M $n_{04}$ $W_{0.2}$N $b_{0.4}$) $O_3$-0.95(PbZ $r_{x}$ $Ti_{1-x}$ ) $O_3$+yN $b_2$ $O_{5}$ , are investigated as a function of the mole ratio of Zr and the amount of N $b_2$ $O_{5}$ . Also, the phase is analyzed by XRD. When the mole ratio of Zr is 0.51, the electromechanical coupling coefficient( $k_{p}$ ), relative dielectric constant ($\varepsilon$$^{T}$ $_{33}$ /$\varepsilon$$_{0}$ ), piezoelectric stain constrain ( $d_{33}$ and dielectric loss tangent show maximum, while the mechanical quality factor shows minimum value ; $k_{p}$ =56.5%, $d_{33}$ =258pC/N, $\varepsilon$$^{T}$ $_{33}$ /$\varepsilon$$_{0}$ =1170, $Q_{m}$ =1150, tan$\delta$=0.51%. At that composition, MPB which rhombohedral and tetragonal phase coexist in this ternary system is shown by the results of XRD analysis. Also, when the amount of N $b_2$ $O_{5}$ is 0.3wt%, the mechanical quality factor is increased to about 2000. The phase transition temperature of the ternary piezoelectric ceramic system showed about 35$0^{\circ}C$.TEX>.>.>.

• 미생물학회지
• /
• 제30권3호
• /
• pp.154-159
• /
• 1992

섬유소 분해능이 우수한 P. verruculosum 의 분생포자로부터 원형질체의 생성 및 재생에 대하여 조사하였다. 균의 원형질체 생성을 위한여 2-deoxy-D-glucose(2-DG) 가 첨가된 최소배지에서 분생포자를 10-12 시간 전배양 시킨후 시판 세포벽분해효소들을 작용시켜 본 결과 그중 Novozyme 234 (1%, w/v) 에서 50% 이상의 가장 좋은 원형질체 생성 수율을 보였다. 전배양 되지 않은 포자로부터는 원형질체 생성이 이루어지지 않았으며 원형질체 생성율을 향상시키기 위한 첨가테로서 2-DG 의 효과가 무첨가에 비해 2배 이상의 수율을 증가시켰다. 포자 원형질체의 재생율은 49.2% 로 동 균주의 균사체 원형질체의 재생율4.6-27.8%(삼투압 조절체로서 0.6 M magnesium sulfate) 보다 높았다. 원형질체 생성 및 재생을 위한 상투압 안정제로서는 0.6M ammonium sulfate 와0.6 M magnesium sulfate가 가장 적절하였다. 광학 형미경을 통하여 부풀린 포자로부터 원형질체의 생성과정과 두 가지 각기 다른 양상의 재생과정이 관찰되었다.

• 한국통신학회논문지
• /
• 제30권3A호
• /
• pp.217-225
• /
• 2005

본 논문은 다양한 무선 통신 표준에서 사용되는 비터비 알고리즘을 위한 전용의 DSP 명령어 및 하드웨어 구조를 제안한다. 제안한 구조는 비터비 알고리즘의 Trace Back(TB) 연산 사이클을 효과적으로 줄일 수 있다. 제안된 비터비 전용 명령어와 하드웨어 구조는 비터비 연산의 Add Compare Select(ACS) 연산 과정과 TB 연산 과정의 병렬 처리가 가능하며, 병렬 연산을 지원하기 위해 트랠리스 버터플라이 연산 과정에서 필요한 데이터를 자동으로 생성하는 Offset Calculation Unit(OCU)을 제안한다. 제안된 OCU는 삼성 SEC 0.18μm라이브러리로 로직 합성하여 1,460 게이트 개수를 가지며, 최대 지연 시간은 5.75ns를 나타내었다. 사용된 ACS-TB 병렬 처리 방식은 Eb/No 값이 6dB인 경우 MLSE 등화기 사용 사용되는 일반적인 TB 연산 방식과 비교하여 거의 동일한 BER 성능을 보여 주었으며, 제안한 DSP는 구속장 K=5 일 때 Carmel DSP와 비교하여 11%, TI TMS320c55x와 비교하여 45%의 연산 사이클이 줄일 수 있다.

• 한국재료학회지
• /
• 제29권12호
• /
• pp.781-789
• /
• 2019

The prediction of Jominy hardness curves and the effect of alloying elements on the hardenability of boron steels (19 different steels) are investigated using multiple regression analysis. To evaluate the hardenability of boron steels, Jominy end quenching tests are performed. Regardless of the alloy type, lath martensite structure is observed at the quenching end, and ferrite and pearlite structures are detected in the core. Some bainite microstructure also appears in areas where hardness is sharply reduced. Through multiple regression analysis method, the average multiplying factor (regression coefficient) for each alloying element is derived. As a result, B is found to be 6308.6, C is 71.5, Si is 59.4, Mn is 25.5, Ti is 13.8, and Cr is 24.5. The valid concentration ranges of the main alloying elements are 19 ppm < B < 28 ppm, 0.17 < C < 0.27 wt%, 0.19 < Si < 0.30 wt%, 0.75 < Mn < 1.15 wt%, 0.15 < Cr < 0.82 wt%, and 3 < N < 7 ppm. It is possible to predict changes of hardenability and hardness curves based on the above method. In the validation results of the multiple regression analysis, it is confirmed that the measured hardness values are within the error range of the predicted curves, regardless of alloy type.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.1244-1245
• /
• 2008

Recently, piezoelectric transformer is applied to wide fields. Multi layer piezoelectric transformer has the advantage of high step up ratio, electromechanical coupling coefficient(Kp) and mechanical quality factor(Qm), but is indicated of peeling-phenomenon of electrode, rising sintering temperature made price of costly electrode. So in this study, it discuss on method for fabrication of rosen type piezoelectric transformers. For the fabrication as rosen type piezoelectric transformers, synthesized the powder using 0.01Pb$(ni_{1/3}Nb_{2/3})O_3$ - 0.08Pb$(Mn_{1/3}Nb_{2/3})O_3$ - 0.91Pb$(Zr_{0506}Ti_{0496})O_3$ (abbreviated as PNN-PMN-PZT) ceramics. The density, microstructure, dielectric and piezoelectric properties as a function of sintering temperature were investigated. The results indicated that the optimized properties of ceramics were obtained at sintering temperature of 1200$^{\circ}C$, showed the value of $d_{33}$=273pC/N, $K_p$=0.60 $Q_m$=1585, ${\varepsilon}_r$=1454, density=7.917$g/cm^3$ and $tan{\delta}$=0.0064.

• 한국재료학회지
• /
• 제14권6호
• /
• pp.402-406
• /
• 2004

$WSi_2$, $TiSi_2$, $CoSi_2$, and $TaSi_2$ are general silicides used today in semiconductor devices. $WSi_2$ thin films have been proposed, studied and used recently in CMOS technology extensively to reduce sheet resistance of polysilicon and $n^{+}$ region. However, there are several serious problems encountered because $WSi_2$ is oxidized and forms a native oxide layer at the interface between $WSi_2$ and $Si_3$$N_4$. In this study, we have introduced 20 $slm-N_2$ gas from top to bottom of the furnace in order to control native oxide films between $WSi_2$ and $Si_3$$N_4$ film. In resulting SEM photographs, we have observed that the native oxide films at the surface of $WSi_2$ film are removed using the long injector system.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.936-936
• /
• 2006

Bulk amorphous materials have been intensively studied to apply for various advanced industry fields due to their high mechanical, chemical and electrical properties. These materials have been produced by several techniques such as mechanical alloying, melt spinning and gas atomization, etc. Among them, the atomization is the most potential technique for commercialization due to high cooling rate during solidification of the melt and mass productivity. However, the amorphous powders still have some limitations because of their low ductility and toughness. Therefore, intensive efforts have to be carried out to increase the ductility and toughness. In this study, the Ni-based amorphous powder was produced by the gas atomization process. And in order to increase the ductile toughness, ductile Cu phase was coated on the Ni amorphous powder by spray drying process. The characteristics of the as-synthesis powders have been examined and briefly mentioned. The master alloy with $Ni_{57}Zr_{20}Ti_{16}Si_2Sn_3$ was prepared by vacuum induction melting furnace with graphite crucible and mold. The atomization was conducted at $1450^{\circ}C$ under the vacuum of $10^{-2}$ torr. The gas pressure during atomization was varied from 35 to 50 bars. After making the Ni amorphous powders, the spray drying was processed to produce the Cu -coated Ni amorphous composite powder. The amorphous powder and Cu nitrate solution were mixed together with a small amount of binder and then it was sprayed at temperature of $130^{\circ}C$ and rotating speed of 15,000 R.P.M.

• 대한전기학회논문지
• /
• 제41권5호
• /
• pp.508-516
• /
• 1992

In this study, dielectric and piezoelectric properties of 0.05Pb(AlS12/3TWS11/3T)OS13T-0.95Pb(ZrS10.52TTiS10.48T)OS13T system ceramics were investigated with respect to the variations of MnOS12T and FeS12TOS13T additions amounts. The results obtained in this study are summarized as follows: 1. As the amounts of MnOS12T and FeS12TOS13T are increased, tetragonality(c/a) and apparent density were decreased but grain size was increased, also the limits of solubility were revealed because pores were formed at the amounts of 0.3wt% MnOS12T and 0.5wt% FeS12TOS13T. 2. AS the increasing of amounts of MnOS12T and FeS12TOS13T, the temperature of phase transition(TS1cT) was decreased, and pemeability had maximum value at the amount of 0.3wt% MnOS12T but were sharply decreasd for the increasing FeS12TOS13T amounts. 3. As the amounts of MnOS12T and FeS12TOS13T are increased, the electro-mechanical coupling factor(kS1pT) was decreased from 60% to 41%, 19% respectively, but mechanical quality factor(QS1mT) had maximum values 720 for amount of 0.3wt% MnOS12T and 320 the amount of 0.5wt% FeS12TOS13T.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.1
• /
• pp.393-396
• /
• 2004

본 논문에서는 완충층용 MgO 박막을 P-type(100)Si 기판위에 작업가스 $Ar:O_2=80:20$, RF 파워 50W, 기판온도 $400^{\circ}C$, 10mtorr의 작업진공에서 $500{\AA}$ 증착하였다. 제작된 MgO/Si 기판위에 RF Magnetron sputtering법으로 작업가스 $Ar:O_2$의 비율을 90:10, 80:20, 70:30으로 변화하면서 $BST(Ba_{0.5}Sr_{0.5}TiO_3)$ 박막을 약 $2000{\AA}$ 증착하였다. XRD 측정결과 작업가스비의 변화에 관계없이(110)BST와 (111)BST 피크만이 관찰되었으며 작업가스 $Ar:O_2=80:20$에서 가장 양호한 결정성을 나타내었다. I-V 측정결과 인가전계 ${\pm}100kV/cm$에서 $10^{-7}A/cm^2$이하의 양호한 누설전류 특성을 보여주고 있으며 C-V 측정결과 작업가스 $Ar:O_2$의 비율 90:10, 80:20, 70:30에서의 비유전율은 각각 283, 305, 296으로서 작업가스비 80:20에서 제작된 박막의 특성이 가장 우수하였다. 작업가스비 80:20에서 제작된 박막의 SEM 측정결과 결정이 성장되었음을 확인할 수 있었고 그레인의 크기는 약 10nm였다.