• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제54권1호
• /
• pp.1-7
• /
• 2005

Thin films of vanadium oxide(VO/sub x/) were deposited by r.f. magnetron sputtering from V₂O/sub 5/ target with oxygen/(oxygen+argon) partial pressure ratio of 0% and 8% and in situ annealed in vacuum at 400℃ for 1h and 4h. Crystal structure, chemical composition, molecular structure, optical and electrical properties of films were characterized through XRD, XPS, RBS, FTIR, optical absorption and electrical conductivity measurements. The films as-deposited are amorphous, but 0%O₂ films annealed for time longer than 4h and 8% O₂ films annealed for time longer than 1h are polycrystalline. As the oxygen partial pressure is increased the films become more stoichiometric V₂O/sub 5/. When annealed at 400℃, the as-deposited films are reduced to a lower oxide. The optical transmission of the films annealed in vacuum decreases considerably than the as-deposited films and the optical absorption of all the films increases rapidly at wavelength shorter than about 550nm. Electrical conductivity and thermal activation energy are increased with increasing the annealing time and with decreasing the oxygen partial pressure.

• 한국재료학회지
• /
• 제13권4호
• /
• pp.205-212
• /
• 2003

RF sputtering process was applied to produce thin hydroxyapatite［HA, Ca10($PO_4$)$_{6}$ $ (OH)_2$films on Ti-6Al-4V alloy substrates. To make a 101.6 mm dia.${\times}$5 mm HA target, the commercial HA powder was first calcinated for 3h at $200^{\circ}C$. A certain amount of the calcinated HA powder was pressed under a pressure of 20,000 psi by the cold isostatic press(CIP) and the pressed HA target was sintered for 6 h at $1,200^{\circ}C$. The effects of different heat treating conditions on the bonding strength between HA thin films and Ti-6Al-4V alloy substrates were studied. Before deposition, the alloy substrates were annealed for 1 h at $850^{\circ}C$ under $3.0${\times}$10^{-3}$ Xtorr, and after deposition, the hydroxyapatite/Ti-6Al-4V alloy thin films were annealed for 1 h at 400, 600 and $800^{\circ}C$ under the atmosphere, respectively. Experimental results represented that the HA thin films on the annealed substrates had higher hardness than non-heat treated substrates before the deposition.

• Transactions on Electrical and Electronic Materials
• /
• 제11권2호
• /
• pp.81-84
• /
• 2010

Al-doped ZnO (AZO) films were prepared by an Ar:$H_2$ gas radio frequency (RF) magnetron sputtering system with a AZO ($2\;wt{\cdot}%\;Al_2O_3$) ceramic target at the low temperature of $100^{\circ}C$ and annealed in hydrogen ambient at the temperature of $300^{\circ}C$. To investigate the influence of the $H_2$ flow ratio on the properties of the AZO films, the $H_2$ flow ratio was changed from 0.5% to 2%. As a result, the AZO films, deposited with a 1% $H_2$ addition, showed a resistivity of $11.7\;{\times}\;10^{-4}\;{\Omega}{\cdot}cm$. When the AZO films were annealed at $300^{\circ}C$ for 1 hour in a hydrogen atmosphere, the resistivity decreased from $11.7\;{\times}\;10^{-4}\;{\Omega}{\cdot}cm$ to $5.63\;{\times}\;10^{-4}\;{\Omega}{\cdot}cm$. The lowest resistivity of $5.63\;{\times}\;10^{-4}{\Omega}{\cdot}cm$ was obtained by adding 1% hydrogen gas to the deposition and annealing process. The X-ray diffraction patterns of all the films showed a preferable growth orientation in the (002) plane. The spectrophotometer measurements showed that the transmittance of 85% was obtained by the film deposited with the $H_2$ flow ratio of 1% at 940 nm for GaAs/GaAlAs LEDs.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.120-120
• /
• 2008

We demonstrate epitaxial growth of ZnO thin films on 4H-SiC(0001) substrates using pulsed laser deposition (PLD). ZnO and SiC have attracted attention for their special material properties as wide band gap semiconductors. Especially, ZnO could be applied to optoelectronic applications such as light emitting devices and photo detectors due to its direct wide bandgap (Eg) of ~3.37eV and large exciton binding energy of ~60meV. SiC shows a good lattice matching to ZnO compared with other commonly used substrates and in this regard SiC is a good candidate as a substrate for ZnO. In this work, ZnO thin films were grown on 4H-SiC(0001) substrates by PLD using an Nd:YAG laser with a 355nm wavelength. The crystalline properties of the films were evaluated by x-ray diffraction (XRD) $\theta-2\theta$, rocking curve and pole figure measurements using a high-resolution diffractometer. The surface morphology of the films was studied by atomic force microscopy (AFM).

• 대한전기학회논문지
• /
• 제40권7호
• /
• pp.670-674
• /
• 1991

This paper presents the material properties of LPCVD silicon films formed using Si2H6 gas at various deposition temperatures. To study the structural properties depending on the deposition temperature, XRD, EBD and TEM analyses were used. The maximum grain size in this experiment was obtained at the deposition temperature of 485ø C. It is discussed that LPCVD films formed below the deposition temperature of 485ø C are promising for low temperature TFT applications. The enhancement of the film characteristics results from the reduction of grain boundary density. We also observed that the film properties of Si2H6 at 600ø C was quite different from those of Si H4 at 600ø C. It has shown that the grain structure from a TEM analysis was elliptical and not dependent on the deposition temperature.

• 대한전자공학회논문지SD
• /
• 제37권8호
• /
• pp.17-27
• /
• 2000

열선 CVD(Hot Wire CVD)를 이용해 유리기판에 미세결정 실리콘(${\mu}c$ -Si:H) 박막을 증착시키고, 증착 조건에 따른 막의 특성변화를 관찰하였다. 열선 CVD법에 의한 ${\mu}c$ -Si:H막의 증착률은 조건변화에 따라 0.2nm/sec에서 3.5nm/sec사이의 값을 가졌으며, 기존의 PECVD법에 비해 10배 이상 높은 값이었다. Raman 특성으로부터 ${\mu}c$ -Si:H막은 비정질과 결정질의 두상이 혼합된 상태임을 알 수 있었으며, 평균 결정 립의 크기는 6-10nm, 결정체적분율은 37~63%범위였다. 막의 전도대와 Fermi 준위의 차를 나타내는 전도 활성화에너지(conductivity activation energy)는 30mTorr에서 0.22eV로 나타났으며, 압력에 따라 증가하여 300mTorr에서는 0.68eV의 값을 가졌다. 막의 활성화 에너지 증가는 높은 압력에서 증착된 막의 특성이 진성(intrisic)에 가까움을 의미하며, 이는 압력증가에 따른 암 전도도의 감소특성으로부터 확인할 수 있었다. 또한 이차이온질량분석으로부터 열선온도 1800$^{\circ}C$에서 증착시킨 막의 텅스텐 함유량은 $6{\times}10^{16}atoms/cm^3$임을 알 수 있었다.

• 한국안광학회지
• /
• 제3권1호
• /
• pp.1-8
• /
• 1998

지주파 PECVD 방법으로 아세틸렌 분암비를 달리하면서 제작한 비정질 탄소 박막에서의 분광 특성을 조사하였다. Raman 분광으로부터 D 피크와 G 피크의 상대적인 세기로부터 $sp^3/sp^2$은 수소함량에 대한 경향성을 알 수가 있었으며, FTIR 분광으로부터 계산된 수소함량은 16~37 atm %, $sp^3/sp^2$d,s 0.22~1.44로 변화하였다. 이와 같은 분광특성에 의하여 최적의 아세틸렌 분압비는~15%임을 알 수가 있었다.

• 한국세라믹학회지
• /
• 제34권8호
• /
• pp.825-833
• /
• 1997

Silicon carbide films were deposited by low pressure chemical vapor deposition(LPCVD) using MTS(CH3SICl3) in hydrogen atmosphere on (100) Si substrate. To prevent the unstable interface from being formed on the substrate, the experiments were performed through three deposition processes which were the deposition on 1) as received Si, 2) low temperature grown SiC, and 3) carbonized Si by C2H2. The microstructure of the interface between Si substrates and SiC films was observed by SEM and the adhesion between Si substrates and SiC films was measured through scratch test. The SiC films deposited on the low temperature grown SiC thin films, showed the stable interfacial structures. The interface of the SiC films deposited on carbonized Si, however, was more stable and showed better adhesion than the others. In the case of the low temperature growth process, the optimum condition was 120$0^{\circ}C$ on carbonized Si by 3% C2H2, at 105$0^{\circ}C$, 5 torr, 10 min, showed the most stable interface. As a result of XRD analysis, it was observed that the preferred orientation of (200) plane was increased with Si carbonization. On the basis of the experimental results, the models of defect formation in the process of each deposition were compared.

• 한국세라믹학회지
• /
• 제33권3호
• /
• pp.299-306
• /
• 1996

We invesgated the fesibility of thin films deposition by pyrolysis of metalorganic precursors using chemical beam deposition (CBD) process. We attempted to understand the effects of deposition variables such as substrate temperature operating pressure effusion cell temperature and H2 partial pressure on the properties of MgF2 grown by CBD. Mg(tfac)2 was used as a precursor. MgF2 thin films were always grown in an amorphous state and crystallized bypost-annealing. he higher the substrate temperature and the lower the operating pressure the less the impurities I the deposited MgF2 thin films. H2 gas has to be supplied for the pyrolitic reaction of Mg(tfac)2 decomposition. MgF2 films annealed in H2 have lower C impurity than those annealed in O2. But their crysatllinity was independent of annealing atmosphere. The optimum conditions for the prepara-tion of MgF2 films by CBD process were as following : The substrate temperature 55$0^{\circ}C$ the operating pressure 10-4 torr; effusion cell temperature 21$0^{\circ}C$ the percentage of H2 100% Post-annealing in H2 gas was required to remove residual carbon and to form MgF2 crystalline phase.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 C
• /
• pp.1592-1594
• /
• 2003

This paper presents the deposition and characterization of microcrystalline silicon(${\mu}c$-Si:H) films by HWCVD(Hot-wire Chemical Vapor Deposition) method at low substrate($300^{\circ}C$). The filament temperature, pressure and $SiH_4$ concentration were determined to be a critical parameter for the deposition of poly-Si films. Series A was deposited under the conditions of $1380^{\circ}C$(Tf), 100 mTorr and $2{\sim}10%\{SC:SiH_4/(SiH_4+H_2)\}$ for 60 min. Series B was deposited under the conditions of $1400{\sim}1450^{\circ}(T_f)$, 30 mTorr and $2{\sim}12%$(SC) for 60 min. The physical characteristics were measured by Raman and FTIR spectroscopy, dark and photoconductivity measurements under AM1.5 illumination.