• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 추계학술대회 논문집
• /
• pp.307-309
• /
• 2008

This study suggests a modeling of grid-connected wind turbine generation system that has induction generator, and aims to perform simulations for outputs by the variation of actual wind speed and for fault current of wind generation system by the transformer winding connection. This study is implemented by matlab&simulink. The simulation shall be performed by assuming single line to ground fault generated in the system. Generator power, generator rotor speed, generator terminal current and fault current shall be observed following the performance of simulation. The fault current change will be dealt through the simulation results for fault current of wind generation system following the grid-connected transformer winding connection and the simulation result by the transformer neutral ground method.

• 제어로봇시스템학회논문지
• /
• 제16권7호
• /
• pp.655-660
• /
• 2010

As increasing the number of Electronic Control Units in a vehicle, the proportion for reliability and stability of the software is going increasingly. Accordingly, the traditional CAN network has occurred the situation that the requirement of developing vehicle software is not sufficient. To solve these problems, the FlexRay network which is ensured the high bandwidth and real-time is generated. However it is difficult to implement FlexRay based application software because of complex protocol than traditional CAN network. Accordingly the system for analysis and verification of network state is needed. Also vehicle vendor develops application software using Matlab/Simulink in order to increase productivity. But this development method is hard to solve the network problem of node to node. Therefore this paper implements Matlab/Simulink based FlexRay network system and verifies it through comparing with existing embedded system.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2007년도 하계학술대회 논문집
• /
• pp.400-402
• /
• 2007

This paper presents a vector control implementation for PMSM using Real Time Workshop and Embedded Target for TI C2000 DSP in MATLAB/SIMULINK. Speed, current and vector controllers are easily designed and implemented by using the MATLAB/SIMULINK program. Feedback of motor speed is processed through C28x QEP(Quadrature Encoder Pulse) block from encoder pulse. 3-Phase currents ares processed through C28x ADC block from current sensors. And gating signal of PWM inverter is generated through SVPWM and PWM block. Real-time program is drawn using SIMULINK and then converted program code for speed control of PMSM is downloaded into the TI eZdsp 2812 board. Experiments were carried out to examine validity of the proposed vector control implementation.

• 한국정보통신학회논문지
• /
• 제13권9호
• /
• pp.1803-1810
• /
• 2009

본 논문은 OFDM을 사용하는 DVB-T 시스템에서 발생하는 IQ 불평형 오류를 추정하고 보상하는 문제를 Matlab으로 성능 평가하고, 이 중 IQ 불평형 오류 추정 보상 회로 부분을 Xilinx의 System Generator를 이용하여 FPGA로 설계 구현하여 성능을 비교 평가한 것이다. 모의실험 결과, Matlab 결과와 System Generator 결과 모두 IQ 불평형 오류가 우수하게 추정 보상됨을 확인하였으며, 또한 구현한 FPGA의 성능을 평가하기 위해 Hardware co-simulation 과정을 통해 Xilinx Sparta3 xc3s1000 fg676-4 target Device에 로딩하고, 타이밍 해석과 resource량도 확인함으로서 성능을 검증하였다.

• 한국산학기술학회논문지
• /
• 제9권2호
• /
• pp.317-326
• /
• 2008

본 논문은 MATLAB/SIMULINK와 dSPACE 1104 시스템을 사용하여 표면부착형 영구자석 동기전동기 벡터제어를 구현하였다. 영구자석 동기전동기는 고정자 전류를 자속발생 전류성분과 토크발생 전류성분으로 분리하고 이를 각각 독립적으로 제어함으로써 타여자 직류전동기처럼 다루는 것이 가능하기 때문에 기존의 직류전동기 제어에 사용되던 각종 제어 알고리즘을 적용하는 것이 가능하게 된다. 본 연구에서는 표면 부착형 영구자석 동기 전동기의 벡터제어를 구현하기 위하여, 먼저 MATLAB/SIMULINK 프로그램으로 영구자석 동기 전동기를 모델링하고 속도제어 부에는 비례-적분 제어기를, 전류제어 부에는 비간섭 비례-적분 제어기를 설계하여 제어기의 응답을 미리 확인하였다. 그리고 설계된 제어기의 성능을 입증하기 위하여 dSPACE DS1104 R&D Board에 시뮬레이션을 통해 구현된 영구자석 동기전동기 벡터 제어 프로그램을 다운로드하여 실험을 통해 제안된 벡터제어 시스템의 타당성을 입증하였다

• 조명전기설비학회논문지
• /
• 제25권3호
• /
• pp.50-64
• /
• 2011

In this paper, a DC-coupled photovoltaic (PV), fuel cell (FC) and ultracapacitor hybrid power system is studied for building microgrid. In this proposed system, the PV system provides electric energy to the electrolyzer to produce hydrogen for future use and transfer to the load side, if possible. Whenever the PV system cannot completely meet load demands, the FC system provides power to meet the remaining load. The main weak point of the FC system is slow dynamics, because the power slope is limited to prevent fuel starvation problems, improve performance and increase lifetime. A power management and control algorithm is proposed for the hybrid power system by taking into account the characteristics of each power source. The main works of this paper are hybridization of alternate energy sources with FC systems using long and short storage strategies to build an autonomous system with pragmatic design, and a dynamic model proposed for a PV/FC/UC bank hybrid power generation system. A simulation model for the hybrid power system has been developed using Matlab/Simulink, SimPowerSystems and Matlab/Stateflow. The system performance under the different scenarios has been verified by carrying out simulation studies using a practical load demand profile, hybrid power management and control, and real weather data.

• 조명전기설비학회논문지
• /
• 제27권9호
• /
• pp.74-82
• /
• 2013

This paper presents a novel maximum power point tracking for a photovoltaic power (PV) system with a direct control plan. Maximum power point tracking (MPPT) must usually be integrated with photovoltaic (PV) power systems so that the photovoltaic arrays are able to deliver maximum available power. The maximum available power is tracked using specialized algorithms such as Perturb and Observe (P&O) and incremental Conductance (indCond) methods. The proposed method has the direct control of the MPPT algorithm to change the duty cycle of a dc-dc converter. The main difference of the proposed system to existing MPPT systems includes elimination of the proportional-integral control loop and investigation of the effect of simplifying the control circuit. The proposed method thus has not only faster dynamic performance but also high tracking accuracy. Without a conventional controller, this method can control the dc-dc converter. A simulation model and the direct control of MPPT algorithm for the PV power system are developed by Matlab/Simulink, SimPowerSystems and Matlab/Stateflow.

• 조명전기설비학회논문지
• /
• 제25권2호
• /
• pp.53-60
• /
• 2011

The available power generated from the FC power plant may not be sufficient to meet sustained load demand, peak demand or transient events. An supercapacitor bank(SCB) can supply a large burst of power, but it cannot store a significant amount of energy. The combined use of FC and SCB has the potential for the better energy efficiency, reducing the cost of FC technology and improved dynamic response. In this paper, A single PEMFC and PEMFC operated in parallel with a SC bank are presented, A new dynamic model of PEMFC system, the converter and controller has been developed for stand-alone applications. The simulation results are presented using Matlab/Simulink, and SimPowerSystems environments. It is confirmed that the results show a good performance and stable DC-link voltage for proposed dynamic and mathematical models developed for the combined FC/SCB.

• 한국항공우주학회지
• /
• 제37권4호
• /
• pp.359-366
• /
• 2009

자동 코드생성이란 MATLAB의 Simulink 환경에서 설계한 블록 다이어그램을 c 코드로 변환시켜 주는 기능으로 MATLAB과의 연동을 통해 소프트웨어 설계부터 검증까지의 통합된 개발환경을 제공함으로서 개발 시간을 크게 줄일 수 있다. 하지만 생성된 c 프로그램을 무인기에 탑재하기 위해서는 소프트웨어의 신뢰성 확보가 필요하며 특히 원본이 되는 Simulink 블록의 검증이 중요하다. 본 연구에서는 자동 코드생성 기능을 고려하여 Simulink 환경에서 구성한 무인기용 자동비행 프로그램을 DO-178B에 명시된 소프트웨어 시험 과정에 따라 검증하였다. 이 과정을 통해 최종 프로그램은 기능 요구사항에 대한 만족함을 확인했을 뿐 아니라 Decision Coverage 93%, Condition Coverage 95% 그리고 MC/DC 90%로 구조적 측면에서 검증을 수행했다.

• 제어로봇시스템학회논문지
• /
• 제19권5호
• /
• pp.442-449
• /
• 2013

In this paper, a simulation system based on X-Plane and MATLAB/Simulink for multiple UAVs is presented. For the conceptual design of this proposed system, a hierarchical system architecture for multiple UAVs is presented. This architecture has object-oriented data structure which consists of three objects (UAV status, mission and task, and environment) and a hierarchy consisting of four layers (decision making layer, task assignment layer, path and motion planning layer, and collision avoidance layer) is also proposed. In addition, this paper shows a implementation of simulation system based on the proposed system architecture using X-Plane and MATLAB/Simulink. The result of simulation from the developed system in this paper validate capability of application for multiple UAVs in real environment.