• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.255-255
• /
• 2011

Zinc oxide based thin films have been extensively studied in recent several years because they have very interesting properties and zinc oxide is non-poisonous, abundant and cheap material. ZnO films are employed in different applications like transparent conductive layers in solar cells, protective coatings and so on. Wide industrial application of the ZnO films requires of development of cheap, effective and scalable technology. Typically used technologies don't completely satisfy the industrial requirements. In the present work, we studied effect of the deposition parameters on the structure and properties of ZnO films deposited by DC arc plasmatron. The varied parameters were gas flow rates, precursor composition, substrate temperature and post-deposition annealing temperature. Vapor of Zinc acetylacetone was used as source materials, oxygen was used as working gas and argon was used as the cathode protective gas and a transport gas for the vapor. The plasmatron power was varied in the range of 700-1500 watts. Flow rate of the gases and substrate temperature rate were varied in the wide range to optimize the properties of the deposited coatings. After deposition films were annealed in the hydrogen atmosphere in the wide range of temperatures. Structure of coatings was investigated using XRD and SEM. Chemical composition was analyzed using x-ray photoelectron spectroscopy. Sheet conductivity was measured by 4-point probe method. Optical properties of the transparent ZnO-based coatings were studied by the spectroscopy. It was shown that deposition by a DC Arc plasmatron can be used for low-cost production of zinc oxide films with good optical and electrical properties. Increasing of the oxygen content in the gas mixture during deposition allow to obtain high-resistive protective and insulation coatings with high adhesion to the metallic surface.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.7
• /
• pp.502-509
• /
• 2018

Epitaxial ZnO nanowires (NWs) were synthesized on sapphire (001) substrates using a hydrothermal process. The effects of the pH value of the precursor solution on the structural and optical properties of the resulting NWs was studied. The epitaxial relationship and the domain matching configuration between the sapphire (001) substrate and the as-grown ZnO NWs were determined using synchrotron X-ray diffraction measurements. The (002) plane of $w{\ddot{u}}rtzite$ ZnO NW grows in the surface normal direction parallel to the sapphire (001) direction. However, three types of in-plane domain matching configurations were observed, such as the on-position, $30^{\circ}$-rotated position, and ${\pm}8.5^{\circ}$-rotated position relative to the on-position, which might be attributed to inheriting the in-plane domain configuration of the ZnO seed layer.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.252.2-252.2
• /
• 2013

ZnO nanostructures have a lot of interest for decades due to its varied applications such as light-emitting devices, power generators, solar cells, and sensing devices etc. To get the high performance of these devices, the factors of nanostructure geometry, spacing, and alignment are important. So, Patterning of vertically- aligned ZnO nanowires are currently attractive. However, many of ZnO nanowire or nanorod fabrication methods are needs high temperature, such vapor phase transport process, metal-organic chemical vapor deposition (MOCVD), metal-organic vapor phase epitaxy, thermal evaporation, pulse laser deposition and thermal chemical vapor deposition. While hydrothermal process has great advantages-low temperature (less than $100^{\circ}C$), simple steps, short time consuming, without catalyst, and relatively ease to control than as mentioned various methods. In this work, we investigate the dependence of ZnO nanowire alignment and morphology on si substrate using of nanosphere template with various precursor concentration and components via hydrothermal process. The brief experimental scheme is as follow. First synthesized ZnO seed solution was spun coated on to cleaned Si substrate, and then annealed $350^{\circ}C$ for 1h in the furnace. Second, 200nm sized close-packed nanospheres were formed on the seed layer-coated substrate by using of gas-liquid-solid interfacial self-assembly method and drying in vaccum desicator for about a day to enhance the adhesion between seed layer and nanospheres. After that, zinc oxide nanowires were synthesized using a low temperature hydrothermal method based on alkali solution. The specimens were immersed upside down in the autoclave bath to prevent some precipitates which formed and covered on the surface. The hydrothermal conditions such as growth temperature, growth time, solution concentration, and additives are variously performed to optimize the morphologies of nanowire. To characterize the crystal structure of seed layer and nanowires, morphology, and optical properties, X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), Raman spectroscopy, and photoluminescence (PL) studies were investigated.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.1
• /
• pp.112-115
• /
• 2010

Transparent conducting undoped and Al impurity doped ZnO films were deposited on glass substrate by spin coat technique using 24 days aged ZnO precursor solution with solution of ethanol and diethanolamine. The films were characterized by UV-Visible spectroscopy, X-ray diffraction (XRD), scanning electron microscope (SEM), electrical resistivity ($\rho$), carrier concentration (n), and hall mobility ($\mu$) measurements. XRD data show that the deposited film shows polycrystalline nature with hexagonal wurtzite structure with preferential orientation along (002) crystal plane. The SEM images show that surface morphology, porosity and grain sizes are affected by doping concentration. The Al doped samples show high transmittance and better resistivity. With increasing Al concentration only mild change in optical band gap is observed. Optical properties are not affected by aging of parent solution. A lowest resistivity ($8.5 \times 10^{-2}$ ohm cm) is observed at 2 atomic percent (at.%) Al. With further increase in Al concentration, the resistivity started to increase significantly. The decrease resistivity with increasing Al concentration can be attributed to increase in both carrier concentration and hall mobility.

• Journal of the Korean Ceramic Society
• /
• v.42 no.6 s.277
• /
• pp.384-390
• /
• 2005

[ ${\alpha}-Al_2O_3$ ] precursor was synthesised by sol-gel method using aluminum sulfate, sodium sulfate and sodium carbonate as law materials. The flaky ${\alpha}-Al_2O_3$ crystals were prepared by heating using precursor about $1,050^{\circ}C$. In this study, the effect of some transition-metal sulfate ($FeSO_4,\;SnSO_4,\;ZnSO_4$) addition have been investigated. When iron sulfate was added, it could see that act on impurities in crystal growth process. In case of tin sulfate, distribution of Platelets was very broad. When flaky ${\alpha}-Al_2O_3$ crystals were prepared zinc sulfate addition, thickness, size, and distribution of platelets was suited to industrial application. The average diameter of flaky ${\alpha}-Al_2O_3$ crystals was about 20 $\mu$m, and its thickness was about 0.3 $\mu$m. Increasing addition of zinc sulfate, thickness of ${\alpha}-Al_2O_3$ platelet was decreased.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.719-723
• /
• 2004

Silica coating on ZnS particles with buffer solution has been investigated. Diluted sodium silicate in water was used as the precursor material and it was diluted in water. Sodium silicate was added drop-wise in the continuously stirred suspension of ZnS in the buffer solution at room temperature. Smooth and evenly distributed silica coated ZnS phosphors has been obtained when the pH of buffer solution was 10, the concentration of sodium silicate in water was 20 wt%, firing temperature was 500 $^{\circ}C$.

• Korean Chemical Engineering Research
• /
• v.54 no.2
• /
• pp.152-156
• /
• 2016

Experimental research on the preparation of photocatalyst for the decomposition of brilliant blue FCF ($C_{37}H_{31}O_9N_2S_3Na_2$) was performed. $TiO_2$ and ZnO powders were prepared from titanium (IV) sulfate and zinc acetate at low reaction temperature and atmospheric pressure by hydrothermal precipitation method without calcination. In addition, $TiO_2$ was prepared with cationic surfactant CTAB (Hexadecyltrimethyl ammonium bromide) at the same conditions. The physical properties of prepared $TiO_2$ and ZnO, such as crystallinity, average particle size and absorbance, were investigated by XRD, Zeta-potential meter and DRS. And, the photocatalytic degradation of brilliant blue FCF has been studied in the batch reactor under UV radiation. For the photocatalysts prepared without CTAB, $TiO_2$ has smaller particle size and larger absorbance and photocatalytic reaction rate than ZnO. And $TiO_2$, prepared with CTAB whose concentration is 1/10 of that of precursor, shows 15% higher than that prepared without CTAB in final photocatalytic degradation ratio of brilliant blue FCF.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.34 no.4
• /
• pp.117-124
• /
• 2024

Zinc oxide nanoparticles were synthesized using the polyol method with ethylene glycol containing hydroxyl groups (-OH). It was confirmed that the zinc compounds prepared by the polyol method were a mixture of zinc carbonate hydroxide (Zn₅(OH)₆(CO₃)₂) and zinc oxide (ZnO) crystalline structures. Calcination at 400℃, 600℃ and 800℃ was performed to examine the effects of calcination temperature on the particle size, morphology and crystallinity of zinc oxide. ZnO powders of calcination at 800 ℃ was evaluated to particle size analysis from ethylene glycol containing precursor solution compared with distilled water based solution. The zinc oxide particles obtained from the former had a particle size of approximately 404 ± 51 nm, whereas those from the latter exhibited a more uniform nanoparticles morphology with a particle size of approximately 109 ± 29 nm. This demonstrates that the addition of ethylene glycol can control the influence of water molecules, enabling the direct synthesis of zinc oxide in the form of uniform nanoparticles.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.2
• /
• pp.1555-1562
• /
• 2015

Metal oxide semiconductors have been applied in several areas, such as solar cells, sensor, optical elements and displays, due to the high surface area, unique electrical and optical characteristics. Zinc oxide among the metal oxide has excellent physicochemical properties. Zinc oxide is a n-type semiconductor with a wide direct transition band gap of 3.37 eV at room temperature and large exciton binding energy of 60 meV. Cation-doped zinc oxide studies were conducted to complement the electrical and optical characteristics. In this paper, Al-doped ZnO was synthesized by hydrothermal synthesis using microwaves. ZnO was synthesized by adjusting the precursor ratio and using different dopants. The optimal ZnO synthesis conditions for crystal shape and optical properties were determined. The optical properties of aluminum doped zinc oxide were then examined by SEM, XRD, PL, UV-vis absorbance spectrum, and EDS.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.3
• /
• pp.525-533
• /
• 2014

ZnO has attracted much attention such as photocatalysts, sensors, piezoelectricity and etc. At present, an economical and rapid synthesis route based on the efficient microwave polyol process is used to synthesized metal-doped ZnO nanoclusters. Diethylene glycol has a property of high polarizability, and is an excellent microwave absorbing agent, thus leading to a high heating rate and a significantly shorter reaction time. In this study, metal-doped ZnO nanoclusters are obtained with different seed volumes, when zinc acetate dihydrate is used as a precursor, and metal acetate hydrate is used as a doped-metal and diethylene glycol is used as a solvent. The obtained metal-doped ZnO nanoclusters were characterized by FE-SEM, XRD, Raman and PSA.