• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.298-299
• /
• 2010

Cu(In, Ga)Se2 (CIGS) 박막 태양전지는 Soda lime glass/Mo/CIGS/CdS/ZnO/ITO/Al 의 구조를 가지고 있다. CIGS 화합물은 direct bandgap 구조를 하고 있으며, 광흡수율이 다른 어떤 물질들 보다 뛰어나 박막으로도 충분히 태양광을 흡수할 수 있다. 또한 Ga의 도핑 농도에 따른 밴드갭 조절도 가능하다. 이러한 성질들로 인해 현재 박막태양전지로서 20.1%의 최고효율을 가지고 있다.[1] CIGS 박막 태양전지에서 p-CIGS layer와 스퍼터링으로 증착되는 n-ZnO layer사이의 buffer 층으로 chemical bath deposition (CBD)-CdS 박막을 주로 사용한다. CBD-CdS 박막은 n-ZnO 스퍼터로 증착 시킬 때, CIGS 층의 손상을 최소화하고, 이 두 층 사이에서의 격자상수와 밴드갭의 차이를 줄여주어 CIGS 박막태양전지의 효율을 증가 시키는 역할을 한다. 하지만, Cd (카드뮴)의 심각한 독성과 낮은 밴드갭(2.4eV)으로 인해 CIGS 층에서의 광흡수율을 줄여, CdS를 대체할 새로운 buffer 층의 필요성이 대두되었다.[2] 그 대안으로 ZnS, Zn(O, S, OH), (Zn, Mg)O, In2S3 같은 물질이 연구되고 있다. 현재 CBD-ZnS를 buffer 층으로 사용한 CIGS 박막태양전지의 효율은 최고 18.6%로 CBD-CdS의 최고효율보다는 약 1.5% 낮지만, ZnS가 높은 밴드갭(3.7~3.8eV)과 Cd-free 물질이라는 점에서 CdS를 대체할 물질로 각광받고 있다. 본 연구에서는 기존의 CdS 박막을 제조하는 방법과 같은 방법인 CBD를 이용하여 ZnS 박막을 제조하였다. ZnS 박막을 제조하기 위해서는 Zinc sulfate, Thiourea, 암모니아가 사용된다. 암모니아의 mol 농도에 따른 CBD-ZnS/CIGS 박막태양전지의 효율 변화를 관찰하기 위해 암모니아의 mol 농도는 1 mol, 2 mol, 3 mol, 4 mol, 5 mol, 6 mol, 그 이상의 과량을 사용하여 실험하였다. 실험 결과, 암모니아농도 5 mol에서 효율 13.82%를 확인할 수 있었다. 최고효율을 보인 조건인 암모니아 농도가 5 mol 일 때, Voc는 0.602V, Jsc는 33.109mA/cm2, FF는 69.4%를 나타내었다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.05a
• /
• pp.47-47
• /
• 2015

Atomic layer deposition (ALD) 방법으로 증착시킨 ZnO 기반의 박막물질들을 다양한 종류의 태양전지에서 TCO, Buffer Layer 등으로 활용하기 위한 노력이 최근 이루어지고 있다. 본 발표에서는 ALD를 이용한 ZnO 기반 박막물질들의 광전소자로의 적용을 위한 요구물성을 맞추기 위한 precursor/reactant의 selection을 포함한 공정 parameter가 박막의 물성에 미치는 영향 및 생산성 향상을 위한 ALD 공정장치 개발 예를 소개하고, 광전소자 특성에 미치는 영향을 살펴보았다.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1996.05a
• /
• pp.70-70
• /
• 1996

• Journal of the Korean Society for Heat Treatment
• /
• v.29 no.6
• /
• pp.272-276
• /
• 2016

Al doped ZnO (AZO) single layer and AZO/Ag bi-layered films were deposited on the glass substrates by radio frequency and direct current magnetron sputtering and then the effect of Ag buffer layer on the electrical and optical properties of the films was investigated. The thicknesses of AZO upper layer was kept as 100 nm, while Ag buffer layer was varied from 5 to 15 nm. The observed results mean that opto-electrical properties of the AZO films is influenced with Ag buffer layer and AZO film with 10 nm thick Ag buffer layer show the higher opto-electrical performance than that of the AZO single layer film prepared in this study.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.10
• /
• pp.648-651
• /
• 2015

The characterizations of zinc oxide (ZnO) buffer layers grown by unbalanced magnetron (UBM) sputtering under various substrate temperatures for inverted organic solar cells (IOSCs) were investigated. UBM sputter grown ZnO films exhibited higher crystallinity with increasing the substrate temperature, resulting in uniform and large grain size. Also, the electrical properties of ZnO films are improved with increasing substrate temperature. In the results, the performance of IOSCs critically depended on the substrate temperature during the film growth because the crystalllinity of the ZnO film affect the carrier mobility of the ZnO film.

• Bulletin of the Korean Chemical Society
• /
• v.26 no.10
• /
• pp.1582-1584
• /
• 2005

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.9
• /
• pp.417-422
• /
• 2002

ZnO thin films were deposited on various substrates, such as Si-(111), SiO$_2$(5000 $\AA$ by thermal CVD)/Si-(100), and SiO$_2$(2000 $\AA$ by RF sputtering)/Si-(100). The (002)-orientation, surface morphology and roughness, and electrical resistivity of deposited films were measured and compared in terms of substrate. Surface acoustic wave(SAW) filters with a multilayered configuration of IDT/ZnO/SiO$_2$/Si were also fabricated and the IDT was obtained using a lift-off method. From the frequency-response characteristics of fabricated devices, the insertion loss and side-lobe rejection were estimated. The experimental results showed that the (002)-oriented growth nature of ZnO films, which played a crucial role of determining the characteristic of SAW device, was strong1y dependent upon the SiO$_2$buffer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.319-320
• /
• 2009

In this study, high-quality Al-N doped p-type ZnO thin films were deposited on n-type Si (100) wafer or Si coated with buffer layer by DC magnetron sputtering in the mixture of $N_2$ and $O_2$ gas. The target was ceramic ZnO mixed with $Al_2O_3$ (2 wt%). The p-type ZnO thin film showed higher carrier concentration $2.93\times10^{17}cm^{-3}$, lower resistivity of $5.349\;{\Omega}cm$ and mobility of $3.99\;cm^2V^{-1}S^{-1}$, respectively. According to PL spectrum, the Al donor energy level depth ($E_d$) of Al-N codoped p-type ZnO film was reduced to about 51 meV, and the N acceptor energy level depth ($E_a$) was reduced to 63 meV, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.419-420
• /
• 2008

In this study, high quality (Al,N)-codoped p-type ZnO thin films were obtained by DC magnetron sputtering. The film on buffer layer grown in 80% $N_2$ ambient shows highest hole concentration of $2.93\times10^{17}cm^{-3}$. The films show hole concentration in the range of $1.5\times10^{15}$ to $2.93\times10^{17}cm^{-3}$, resistivity of 131.2 to 2.864 $\Omega$cm, mobility of 3.99 to 31.6 $cm^2V^{-1}s^{-1}$. The films on Si show easier p-doping in ZnO than those on buffer layer. The film on Si shows the highest quality of optical photoluminescence (PL) characteristics. The donor energy level $(E_d)$ of (Al,N)-codoped ZnO films is about 50 meV and acceptor energy level $(E_a)$ is in the range of 63 to 71 meV. It will help to improve p-type ZnO films.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.4
• /
• pp.665-670
• /
• 2020

Buffer layer in CIGS thin-film solar cells improves energy conversion efficiency through band alignment between the absorption layer and the window layer. ZnS is a non-toxic II-VI compound semiconductor with direct-transition band gaps and n-conductivity as well as with excellent lattice matching for CIGS absorbent layers. In this study, the structural and optical properties of ZnS thin films, deposited by RF magnetron sputtering method and subsequently performed by the rapid thermal annealing treatment, were investigated for the buffer layer. The zincblende cubic structures along (111), (220), and (311) were shown in all specimens. The rapid thermal annealed specimens at the relatively low temperatures were polycrystalline structure with the wurtzite hexagonal structures along (002). Rapid thermal annealing at high temperatures changed the polycrystalline structure to the single crystal of the zincblende cubic structures. Through the chemical analysis, the zincblende cubic structure was obtained in the specimen with the ratio of Zn/S near stoichiometry. ZnS thin film showed the shifted absorption edge towards the lower wavelength as annealing temperature increased, and the mean optical transmittance in the visible light range increased to 80.40% under 500℃ conditions.