• Electrical & Electronic Materials
• /
• v.8 no.6
• /
• pp.693-698
• /
• 1995

We fabricated Zinc Oxide transparent conductive thin films with 2wt% of A1203 doping using rf magnetron sputtering. And we investigated electrical and optical characteristics of them which were made with conditions ; rf power 60-300W, thickness of film 3000 11000.angs.. Resistivity, carrier concentration and Hall mobility were investigated for electrical characteristics. Transmittance and optical band gap were investigated with Spectrophotometer in the wavelength range between 200-900 nm. As a result, ZnO thin film fabricated with rf power of 180W and thickness of 5000.angs. showed the best properties. At the best condition, the sample has resistivity of 1*10$\^$-4/.ohm.cm and transmittance of 95% in the visible range.

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.4
• /
• pp.225-228
• /
• 2017

In this study, zinc tin oxide (ZTO) films were prepared on indium tin oxide (ITO) glasses and annealed at different temperatures under vacuum to investigate the correlation between the Ohmic/Schottky contacts, electrical properties, and bonding structures with respect to the annealing temperatures. The ZTO film annealed at $150^{\circ}C$ exhibited an amorphous structure because of the electron-hole recombination effect, and the current of the ZTO film annealed at $150^{\circ}C$ was less than that of the other films because of the potential barrier effect at the Schottky contact. The drift current as charge carriers was similar to the leakage current in a transparent thin-film device, but the diffusion current related to the Schottky barrier leads to the decrease in the leakage current. The direction of the diffusion current was opposite to that of the drift current resulting in a two-fold enhancement of the cut-off effect of leakage drift current due to the diffusion current, and improved performance of the device with the Schottky barrier. Hence, the thin film with an amorphous structure easily becomes a Schottky contact.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.166-166
• /
• 2010

Recently, TFTs based on amorphous oxide semiconductors (AOSs) such as ZnO, InZnO, ZnSnO, GaZnO, TiOx, InGaZnO(IGZO), SnGaZnO, etc. have been attracting a grate deal of attention as potential alternatives to existing TFT technology to meet emerging technological demands where Si-based or organic electronics cannot provide a solution. Since, in 2003, Masuda et al. and Nomura et al. have reported on transparent TFTs using ZnO and IGZO as active layers, respectively, much efforts have been devoted to develop oxide TFTs using aforementioned amorphous oxide semiconductors as their active layers. In this thesis, I report on the performance of thin-film transistors using amorphous indium gallium zinc oxides for an active channel layer at room temperature. $SiO_2$ was employed as the gate dielectric oxide. The amorphous indium gallium zinc oxides were deposited by RF magnetron sputtering. The carrier concentration of amorphous indium gallium zinc oxide was controlled by oxygen pressure in the sputtering ambient. Devices are realized that display a threshold voltage of 1.5V and an on/off ration of > $10^9$ operated as an n-type enhancement mode with saturation mobility with $9.06\;cm^2/V{\cdot}s$. The devices show optical transmittance above 80% in the visible range. In conclusion, the fabrication and characterization of thin-film transistors using amorphous indium gallium zinc oxides for an active channel layer were reported. The operation of the devices was an n-type enhancement mode with good saturation characteristics.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.293.2-293.2
• /
• 2016

The In this paper, we have fabricated the solution processed In-Ga-ZnO thin film transistors (IGZO TFTs) by varying indium and gallium ratio. The indium ratio of IGZO TFTs was changed from 1 to 5 at fixed gallium and zinc oxide atomic percent of 1:1 and gallium ratio was varied from 1 to 5 at fixed indium and zinc oxide atomic percent of 1:1. When the indium ratio was increased at fixed gallium and zinc oxide ratio of 1:1, threshold voltage was negatively shifted from 1.03 to -6.18 V and also mobility was increased from 0.018 to $0.076cm2/V{\cdot}sec$. It means that the number of carriers in IGZO TFTs were increased due to great formation of the oxygen vacancies which generate electrons. In contrast, when the gallium ratio was increased in IGZO TFTs with indium and zinc oxide ration of 1:1, the on/off current ratio was increased from $1.88{\times}104$ to $2.22{\times}105$. It is because gallium have stronger chemical bonds with oxygen than that with the zinc and indium ions that lead to the decreased in electron concentration.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.926-929
• /
• 2007

A significant progress has been made in the characterization of zinc oxide (ZnO) semiconductor as a new semiconductor layer instead of amorphous Si semiconductor used in thin film transistor due to its high electron mobility at low deposition temperature which is quite suitable for flexible display and OLED devices. The wet pattering of ZnO is another important issue with regard to mass production of ZnO thin film transistor device. However, the wet behavior of ZnO thin film in aqueous wet etching solutions conventionally used un TFT industry has not been reported yet, in this work, wet corrosion behavior of RF magnetron sputtered ZnO thin film in various wet solutions such as phosphoric and nitric acid solutions was studied using by electrochemical analysis. The effects of deposition parameters such as RF power and oxygen partial pressure on corrosion rate are also examined.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.5
• /
• pp.382-386
• /
• 2019

The alignment characteristics of liquid crystal (LC) molecules on a solution-derived lanthanum zinc oxide (LZO) film under ion-beam irradiation were demonstrated. Using the solution process, an LZO film was fabricated on the glass substrate and cured at $100^{\circ}C$. Afterwards, ion-beam irradiation was performed following the LC alignment method. Using this film, an LC cell was fabricated and the characteristics of the LC alignment were verified. Cross polarizing microscopy and the crystal rotation method were used to investigate the alignment state of the LC molecules on the LZO films. Furthermore, field emission scanning electron microscopy and X-ray photoelectron spectroscopy were used to explore the effect of the ion-beam irradiation on the LZO film. Through these, it was confirmed that the ion-beam irradiation induced surface modification, which demonstrated anisotropic physical and chemical surface characteristics. Due to this, uniform LC alignment was achieved. Finally, the residual DC and anchoring energy of the LC cell based on the LZO films were measured using a capacitance-voltage curve.

• Journal of the Semiconductor & Display Technology
• /
• v.13 no.1
• /
• pp.43-49
• /
• 2014

Zinc-tin oxides (ZTO) thin film transistors have been fabricated at different process pressure via re sputtering technique. TFT properties were improved by depositing channel layers at lower pressure. From the analysis of TFTs comprised of multi layer channel, deposited consecutively at different sputtering pressure, it was suggested that the electrical characteristics of TFTs were mainly affected by interfacial layer due to their high conductance, however, the stability under the NBIS condition was influenced by whole bulk layer due to low concentration of positive charges, which might be generated by the oxygen vacancy transition, from Vo0 to $Vo^{2+}$. Those improvements were attributed to increasing sputtered target atoms and decreasing harmful effects of oxygen molecules by adopting low sputtering pressure condition.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.215-219
• /
• 2007

In this work, the indium zinc oxide (IZO) films had been deposited on the glass substrate coated with the SiO film. Based on a comparative investigation of the IZO monolayer and IZO/SiO multilayer, it is shown that the thickness of SiO film has a great effect on the mechanical properties of the thin films. The AFM images of the IZO thin film included the SiO film were shown smoother surfaces than monolayer. Resistivity was in inverse proportion to Mobility. If it deposited the SiO film on the substrate, the layer of change was generated between two layer(SiO and substrate). The layer of change influenced resistance because of oxygen content was more than the IZO monolayer.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.373-373
• /
• 2012

We fabricated conductive zinc oxide (ZnO) thin film at low temperature by UV-enhanced atomic layer deposition. The atomic layer deposition relies on alternate pulsing of the precursor gases onto the substrate surface and subsequent chemisorption of the precursors. In this experiment, diethylzinc (DEZ) and $H_2O$ were used as precursors with UV light. The UV light was very effective to improve the conductivity of the ZnO thin film. The thickness, transparency and resistivity were investigated by ellisometry, UV-visible spectroscopy and Four-point probe.

• Journal of Adhesion and Interface
• /
• v.16 no.3
• /
• pp.95-100
• /
• 2015

In this work, we observed the effect of silica, zinc oxide, zinc ion coated silica on carboxylic acid modified styrenic thermoplastic elastomer (m-TPS) film for friction-induced surface fracture. m-TPS film added general silica showed poor mechanical properties, anti-abrasion and friction-induced surface fracture, caused by strong filler-filler interaction of silica. In case of m-TPS films added zinc oxide or zinc ion coated silica, mechanical properties, anti-abrasion and friction-induced surface fracture were improved due to forming ionic cluster between carboxylic acid group of m-TPS and zinc ion. Ionic cluster were confirmed by FT-IR analysis that observed zinc carboxylated group stretch peak at $1550{\sim}1650cm^{-1}$.