• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.224-224
• /
• 2016

Many researchers have been tried to improve the performance of the phosphorescent organic light-emitting diode(PHOLED) by controlling of the dopant profile in the emission layer. In this work, as shown in Fig. 1 insert, a typical red PHOLED device which has the structure of ITO/NPB(50nm)/CBP(30nm)/TPBi(10nm)/Alq3(20nm)/LiF(0.8nm)/Al(100nm) is fabricated with a 5nm thick doping section in the emission layer. The doping section is formed by co-deposition of CBP and Ir(btp)2acac with a doping concentration of 8%, and it's location(x) is changed from HTL/EML interface to EML/HBL in 5nm steps. The current efficiency versus current density of the devices are shown in Fig. 1. By changing the location of doping section, as shown in Fig. 1 and 2, at x=5nm, the efficiency shows the maximum of 3.1 cd/A at 0.5 mA/cm2 and it is slightly decreased when the section is closed to HTL and slightly increased when the section is closed to HBL. If the doping section is closed to HTL(NPB) the excitons can be quenched easily to NPB's triplet state energy level(2.5eV) which is relatively lower than that of CBP(2.6eV). Because there is a hole accumulation at EML/HBL interface the efficiency can be increased slightly when the section is closed to HBL. Even the thickness of the doping section is only 5nm,. the maximum efficiency of 3.1 cd/A with x=5 is closed to that of the homogeneously doped device, 3.3 cd/A, because the diffusion length of the excitons is relatively long. As a result, we confirm that the current efficiency of the PHOLED can be improved by the doping profile optimization such as partially, not homogeneously, doped EML structure.

• Transactions of Materials Processing
• /
• v.7 no.5
• /
• pp.465-473
• /
• 1998

The effect of alloying elements of Ag-Cu-Zr-X brazing alloy on the microstructure and the bond strength of $Al_2O_3/Ni-Cr$ brazed steel joint was investigated. The reaction layer, $ZrO_2$ (a=5.146 ${\AA}$ , b=5.213 ${\AA}$ , c=5.311 ${\AA}$ )was formed at the interface of $Al_2O_3/Ni-Cr$ steel joint by the redox reaction between alumina and Zr. The addition of An and Al to the Ag-Cu-Zr brazing alloy gave rise to changes in the thickness of the reaction product layer and the morphology of the brazement. Sn caused the segregation of Zr was decreased b Al the $ZrO_2$ layer formed at the Ag-Cu-Zr-Al alloy was thinner than that of $ZrO_2$ formed at the Ag-Cu-Zr-An alloy. The fracture shear strength was strongly dependent on the microstructure of the brazement. Brazing with Ag-Cu-Zr-Sn alloy resulted in a better bond strength than with Ag-Cu-Zr or Ag-Cu-Zr-Al alloy.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.9
• /
• pp.2547-2552
• /
• 2010

CdS nano-particulate films were prepared at the air/water interface under Langmuir monolayers of arachidic acid (AA) via interfacial reaction between $Cd^{2+}$ ions in the subphase and $H_2S$ molecules in the gaseous phase. The films were made up of fine CdS nanoparticles with hexagonal Wurtzite crystal structure after reaction. It was revealed that the formation of CdS nano-particulate films depends largely on the experimental conditions. When the films were ripened at room temperature or an increased temperature ($60^{\circ}C$) for one day, numerous holes were appeared due to the dissolution of smaller nanoparticles and the growth of bigger nanoparticles with an improved crystallinity. When the films were ripened further, CdS rodlike nanoparticles with cubic zinc blende crystal structure appeared due to the re-nucleation and growth of CdS nanoparticles at the stacking faults and defect structures of the hexagonal CdS grains. These structures were characterized by transmission electron microscopy (TEM), high-resolution TEM (HRTEM), and X-ray diffraction (XRD). These results declare that CdS semiconductor nanoparticles formed at the air/water interface change their morphologies and crystal structures during the ripening process due to dissolution and recrystallization of the particles.

• Journal of the Korean Magnetics Society
• /
• v.7 no.1
• /
• pp.38-43
• /
• 1997

For amorphous $Co_{1-x}Ti_x$(X=0.13, 0.16, 0.21 at.%) thin films deposited by DC magnetron sputtering method ferromagnetic resonance experiments have been used to investigate the dependence of surface magnetic properties according to annealing temperature (150~225 $^{\circ}C$). Spin wave resonance spectra for all annealing temperatures consist of several volume modes and one(or two) surface mode. It is suggested that both surfaces of the film have a perpendicular hard axis to the film plane(negative surface anisotropy). Also, the surface anisotropy $K_{s2}$ at substrate film interface is varied slowly from -0.11 to -0.25 erg/ $\textrm{cm}^2$ and the surface anisotropy $K_{s1}$ at film-air interface is varied from 0.16 to -0.53 erg/ $\textrm{cm}^2$ with increasing annealing temperature. We conjecture that the variation of surface anisotropy $K_{s1}$ is due to the increase of Co concentration resulted from Ti oxidation for low temperature annealing(150~200 $^{\circ}C$) and the diffusion of Co atoms near the film surfaces for high temperature annealing(225~250 $^{\circ}C$).

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.30B no.6
• /
• pp.86-92
• /
• 1993

In this paper, we present a VLSI chip design of Multi-layer Bidirectionsl Associative Memory with good error-correction performance. The MBAM neural chip utilizes inner product implementation schems with binary storage and analog calculation.. Multi-layer can be constructed by direct cascading of these chips, and the number of neurons is expandable by parallel connection of these chips. We made proto-type chips and interface board to test the expansion. Currently the Chip has 32 input nodes, 32 output nodes, and can store up to 48 patterns, 32x48x2 SRAMs are included in the chip.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.05a
• /
• pp.254-254
• /
• 2012

The purposed of this work was to determine surface charateristics of anodized Ti-30Nb-xTa alloys with Ta content. Samples were prepared by arc melting, followed by followed by homogenization for 12 hr at $1000^{\circ}C$ in argon atmosphere. The electrolyte for anodization treatment was prepared by mixing 465ml $H_2O$ with 35M $H_3PO_4$ and anodized at 180V to 220V. The microstructures of the alloys were examined by X-ray diffractometer (XRD) and optical microscopy (OM). Surface characteristics of anodized Ti-30Nb-xTa alloys was investigated by potentiodynamic test and potentiostatic in 0.9% Nacl solution at $36.5{\pm}1^{\circ}C$. It was observed that the changed ${\alpha}$ phase to ${\beta}$ phase with Ta content.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.17 no.12
• /
• pp.1412-1422
• /
• 1992

This paper describes an implementation of the document class editor based on ODA(Open Document Architecture). For processing, we divided document structure into generic logical structure and generic layout structure as ODA standard. Also this editor could edit document profile. Using the utility which was implemented to investigate the composed document by object. we confirmed the document. And we could verify the ODIF stream data of the document. We designed this editor based on DAP level 2 of international functional standard. This system was implemented in environment of the X window system and the Motif as graphical user interface. This document class editor will be used to create real document having specific document structure.

• Journal of Surface Science and Engineering
• /
• v.49 no.2
• /
• pp.135-140
• /
• 2016

In this study, we prepared magnesium ion containing oxide films formed on the Ti-6Al-4V using plasma electrolytic oxidation (PEO) treatment. Ti-6Al-4V surface was treated using PEO in Mg containing electrolytes at 270V for 5 min. The phase, composition and morphology of the Mg ion containing oxide films were evaluated with X-ray diffraction (XRD), Attenuated total reflectance Fourier transform infrared (ATR-FTIR) and filed-emission scanning electron microscopy (FE-SEM) with energy dispersive X-ray spectrometer (EDS). The biocompatibility of Mg ion containing oxide films was evaluated by immersing in simulated body fluid (SBF). According to surface properties of PEO films, the optimum condition was formed when the applied was 270 V. The PEO films formed in the condition contained the properties of porosity, anatase phase, and near 1.7 Ca(Mg)/P ratio in the oxide film. Our experimental results demonstrate that Mg ion containing oxide promotes bone like apatite nucleation and growth from SBF. The phase and morphologies of bone like apatite were influenced by the Mg ion concentration.

• Proceedings of the IEEK Conference
• /
• 2003.07b
• /
• pp.1061-1064
• /
• 2003

In this paper, we deposited A1$_2$O$_3$ thin film using atomic layer deposition(ALD) method on Ti and fabricated metal-insulator-metal(MIM) capacitor. In the result of this study, the typical deposition rate was about 1.12$\AA$/cycle. About 30 nm of Ti was consumed during deposition and TiO$_{x}$ was formed at the interface of A1$_2$O$_3$ and Ti. Its surface roughness was 1.54nm. The leakage current density was 1.5 nA/$\textrm{cm}^2$. The temperature coefficient of capacitance(TCC) of MIM capacitor was 41 ppm/$^{\circ}C$ at 1MHz and 100 ppm/$^{\circ}C$ at 100 kHz.z.

• Archives of Metallurgy and Materials
• /
• v.65 no.4
• /
• pp.1297-1301
• /
• 2020

The purpose of this study was to investigate the mechanical properties of beta type aged Ti-4Mo-4Cr-X (X = V, Sn, Zr) quaternary alloy for use as a cardiovascular stent. Titanium (Ti) alloys were fabricated using a vacuum arc remelting furnace process. To homogenize the specimens of each composition and remove the micro segregation, all cast specimens were subjected to homogenization at 850℃ for 4 h, which was 100℃ higher than the β-transus temperature of 750℃. The tensile strength and elongation of the aged Ti-4Mo-4Cr-X (X = V, Sn, Zr) alloys were increased as compared to the homogenized alloys. In addition, many α/β interface boundaries formed after aging treatment at 450℃, which acted as inhibitors of strain and caused an increase in tensile strength. The elongation of Ti-4Mo-4Cr-X alloys consisting of α + β phases after aging treatment was improved by greater than 30%. Results of a potentiodynamic polarization test showed that the lowest current density of Ti-4Mo-4Cr-4Sn with 1.05 × 10^-8 A/cm² was obtained. The present Ti-4Mo-4Cr-X alloys showed better corrosion characteristics as compared to the 316L stainless steel and L605 (Co-Cr alloy) cardiovascular stent alloys.