• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제49권2호
• /
• pp.110-115
• /
• 2000

This paper describes the driving principles genometrically and analyzed the generating torque with the structure of magnetostatic wobble motor and electrostatic wobble motor. Then we compare the torque characteristics of magnetostatic wobble motor with those of electrostatic wobble using. F.E.M. Through the results, we investigate how the changes of design affect torque characteristics.

• 연구논문집
• /
• 통권33호
• /
• pp.53-65
• /
• 2003

Electrostatic micro-motors can be divided into three classes: (i) salient type side drive motor, (ii) radial gap type wobble motor, (iii) axial gap type wobble motor. The working mechanism, torque evaluation, fabrication, and operational characteristics of each micro motors are compared. It is proved that axial gap type wobble motor has the bigger generating torque than that of the other type. The gear ratio of wobble motors increases the driving torque at the cost of a decreasing angular speed and decreases the friction because of the rolling motion instead of sliding at the bearing. Techniques for characterizing micro-motors performance are presented.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 A
• /
• pp.336-338
• /
• 1999

This paper analyzes the torque characteristics with the structure of magnetostatic wobble motor and then compares the torque characteristics of magnetostatic wobble motor with those of electrostatic wobble motor using F.E.M. Through the results, we investigates how design parameters' change affect torque characteristics.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 A
• /
• pp.339-341
• /
• 1999

This paper presents the gear ratio of wobble motor, accounting for finite friction in contact point. The gear ratio of a wobble motor is affected by rotor slip, which is a function of motive torque, excitation angle, and friction torque. The gear ratio of a wobble motor can be expressed as a constant term plus a term that accounts for rotor slip. The ideal gear ratio is constant term and is equal to the rotor radius divided by the distance between the center of the rotor and the center of the stator. The rotor-slip term is shown to be directly proportional to the contact point friction torque and inversely proportional to the square of the excitation voltage.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 B
• /
• pp.726-728
• /
• 2000

In this paper, after considering the standard data that are obtained by the study of the dynamic and mechanical characteristics (such as the torque characteristics and the force distribution analysis of the wobble motor), we design the prototype of the magnetostatic wobble motor. It can be applied to the high-precision medical instruments such as the ultrasonic catheter for the diagnosis and treatment of vascular disease.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 추계학술대회 논문집 학회본부 B
• /
• pp.238-240
• /
• 2000

We designed the prototype of electromagnetic wobble motor which could be applied to ultrasonic catheter in the before study. So, In this paper we perform 3D FEM of the designed prototype model with the computer analysis tool(Magnet 6.4). Therefore we prove the characteristics and theorems of the wobble motor with 3D FEM.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 추계학술대회 논문집 학회본부 A
• /
• pp.9-11
• /
• 1999

This paper presents the problems of design and theoretical model of electrostatically driven axial-gap type wobble motor. The motor design benefits from large axial rotor-to-stator overlap and large gear ratios, and motor designs with rotor radii of 50 and $100{\mu}m$ are capable of generating torques in the [nNm] range at high electrostatic fields. Because of the large gear ratio, smaller angular steps and lower rotational speed are obtained, compared to radial-gap motor design. Aspects like gear ratio, torque generation, excitation schemes and torque coverage, normal forces, friction are addressed.

• 한국기계가공학회지
• /
• 제20권2호
• /
• pp.38-44
• /
• 2021

To cater to the transition from single-color to multicolor/multi-material printing, this paper proposes a cartridge-replacing type multi-nozzle Fused Depositon Modeling(FDM) three-dimensional (3D) printer. In the test printing run, tool change failure/wobble/layer shift occurred. It was confirmed that improper support was the cause of this tool change failure. As a solution, spline and electromagnetic cartridges were designed. Wobble was caused by machine vibration and the motor stepping out. To minimize wobble, an additional Z-axis was installed, and the four-point bed leveling method was used instead of the three-point bed leveling method. The occurrence of layer shift was ascribed to the eccentricity of the Z-axis lead screw. Therefore, slit coupler was replaced with an Oldham type. In addition to the mechanical supplementation, the control environment was integrated to prevent accidents and signal errors due to wire connections. Before the final test printing run, a rectifier circuit was added to the motor to secure precise control stability. The final test printing run confirmed that the wobble/layer shift phenomenon was minimized, and the maximum error between layers was reduced to 0.05.

• Journal of Welding and Joining
• /
• 제17권3호
• /
• pp.71-78
• /
• 1999

The welded metal bellows is commonly manufactured by welding pairs of washer-shaped discs of thin sheet metal stamped from strip stock in thickness from 0.025 to 0.254 mm. The discs, or diaphragms, are formed with mating circumferential corrugations. In this study, the diaphragms were welded by using a CW Nd: YAG laser to form metal bellows. The bellows was fixed on a jig and compressed axially, while Cu-rings were installed between belows edges for intimate contact of edges. The difference between the inner diameter of bellows and jig shaft causes an eccentricity, while the tolerance between motor shaft and jig shaft causes a wobble type motion. A vision sensor which is based on the optical triangulation was used for seam tracking. An image processing algorithm which can distinguish the image by bellows edge from that by Cu-ring was developed. The geometric relationship which describes the eccentricity and wobble type motion was modeled. The seam tracking using the image processing algorithm and the geometric modeling was performed successfully.

• 한국수소및신에너지학회논문집
• /
• 제34권1호
• /
• pp.59-68
• /
• 2023

In this study, the performance of high-pressure fuel pumps was compared to find a high-pressure pump suitable for dimethyl ether (DME) fuel, and to establish a database of basic data on flow rates. The use of DME in compression ignition engines can reduce pollutant emissions. The cetane value of DME is higher than that of diesel fuel. The physical properties of DME are similar to liquefied gasoline gas (LPG), and when pressurized at a pressure of 6 bar or more, it changes from gas to liquid. Two types of high pressure pumps used in this study were independent injection type pump and a wobble plate type pump. Two high-pressure pumps with different injection types were compared. By measuring and comparing the performance changes of the two high-pressure pumps, a pump suitable for DME was selected and performance improvement measures were proposed. The changed experimental conditions to measure the performance change of the high pressure pump were increased in the units of 100 to 1,000 rpm and 100 rpm, and the experiment was performed at common rail pressures 300 and 400 bar. it was confirmed that the DME inside the fuel supply system remained in a liquid state through temperature sensors, pressure sensors, and pressure gauges. As a result of the experiment, it was confirmed that the flow rate discharged from the high-pressure fuel pump increased as the motor rotational speed increased, and the flow rate of the high-pressure fuel pump