• The Transactions of the Korean Institute of Power Electronics
• /
• v.24 no.1
• /
• pp.62-65
• /
• 2019

Wireless power transfer systems require an algorithm to determine the presence of the target object for mitigating standby power and safety issues. Although many schemes that sense various external objects have been actively proposed for inductive power transfer systems, not many studies on capacitive power transfer systems have been conducted compared with those on inductive power transfer systems. This study proposes a target object detection algorithm by monitoring the capacitance in transmitter-side electrodes without additional pressure sensors or distance sensors. The proposed algorithm determines the presence of a target object by monitoring the change in capacitance in transmitter-side electrodes using the step pulse of the microcontroller unit. The algorithm is verified by two step processes. First, the performance in capacitance measurement is compared with that of an LCR meter. Then, the verification is conducted in a 5-W capacitive power transfer hardware. Experimental result shows that the interelectrode capacitance increases by 6 times when the target object is fully aligned. Thus, the proposed scheme can successfully detect the presence of the target object.

• Proceedings of the IEEK Conference
• /
• 2003.11c
• /
• pp.259-262
• /
• 2003

In this paper, we designed and implemented digital wireless audio system with embedded RTOS using Bluetooth. Transmitter is consisted of a Settopbox, FIFO for interface block, Microprocessor(ARM7TDMI), UART driver and Bluetooth module. Receiver is consisted of a Microprocessor, AC-3 decoder, Bluetooth module and a Speaker with Amp. We programed Bluetooth protocal stack of HCI, L2CAP, and RFCOMM, so that Bluetooth module interacts with CPU.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.9
• /
• pp.883-891
• /
• 2013

In wireless smart phone charging scenario, the transmitter pad is larger than the size of the receiver pad. Thus, it is important to supply a constant power to the receiver regardless of its location. In this paper, we propose a new method to regulate the receiver's power by adjusting a drain bias of class E power amplifier. The proposed LF-band wireless power transfer system is as follows: a buck converter power supply which is controlled by a pulse width modulation(PWM) IC TL494, a class E amplifier using a low cost IRF510 power MOSFET, a transmitter coil whose dimension is $16cm{\times}18cm$, a receiver coil whose dimension is $6cm{\times}8cm$, and a full bridge rectifier using Schottky diodes. A measured performance show a maximum output power of 4 W and system efficiency of 67 % if we fix the bias voltage. If we adjust the bias voltage, the received power can be maintained at a constant power of 2 W regardless of receiver pad location.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39B no.12
• /
• pp.873-875
• /
• 2014

In this paper we describe an asynchronous MAC protocol with receiver-initiated duty cycling for energy-efficiency in wireless sensor networks(WSN). Legacy asynchronous MAC protocols, X-MAC and PW-MAC, has weaknesses which generates too many control packets and has data collision problem between multiple transmitters, respectively. Therefore, we propose a receiver-initiated asynchronous MAC protocol which generates control packets from transmitter to complement these disadvantages. Compared to the prior asynchronous duty cycling approaches of X-MAC and PW-MAC, the proposed protocol shows a improvement in energy-efficiency, throughput and latency from simulation results.

• Ocean Systems Engineering
• /
• v.8 no.1
• /
• pp.33-39
• /
• 2018

The paper presents a numerical underwater channel model developed in MATLAB for estimating the optical link budget between a light emitting diode (LED) based optical transmitter and a photo diode (PD) receiver when operated in the harbor, coastal and deep waters locations in the Bay of Bengal. The water samples are collected at different locations in the Bay of Bengal using a water sampler during an offshore research cruise. The optical attenuation, the main inherent parameter determining the range of the optical communication link is identified for the different waters using an underwater irradiance measurement system in the laboratory. The identified parameters are applied to the numerical model and found that a 10 W LED and a photo diode based system can provide the optical budget required for a horizontal underwater communication range of about 0.5, 14 and 35 m in the harbor, coastal and deep waters locations respectively. By increasing the transmitter power to 50 W, the operating range of the communication link could be increased up to 53 m in deep water locations in the Bay of Bengal.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.1
• /
• pp.539-542
• /
• 2005

In this paper, we propose a wireless data access system, which used direct sequence spread spectrum method and the ISM band with 900MHz radio frequency. By applying bi-directional transmission between wireless transmitter and receiver, it can be effectively connected with any kinds of RF-ID with 900MHz ISM band. Therefore it could economically be used as peripheral equipments for RF-ID system.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2006.05a
• /
• pp.500-503
• /
• 2006

This paper gives a Wireless lightning detecting and warning system. This system composed of transmitter and receiver. It promptly senses lightning strikes on the power lines and transmission towers by using the lightning current detection circuit in a small transmitter situated on the top of power tower, and it sends the number of lightning strikes and the ID. of the tower to patrols through the receivers. This system will be used to discover the exact location of a lightning strike.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.8 no.6
• /
• pp.600-613
• /
• 1997

The implementation of a BTS(Base station Transceiver) for WLL system using W-CDMA(Wideband-Code Division Multiple Access) method is presented in this paper. It consists of three boards; receiver, transmitter and RF controller. Some RF parameters are considered and simulated by the RF simulation S/W using commercial and customized components specifications. The implemented transceiver of 5 MHz RF channel bandwidth satisfies the system requirements of a transceiver such as dynamic range, sensitivity in the receiver and spurious emission suppression in the transmitter. At the receiver, the experimental measurement showed 2.86 dB of NF and 60 dB above of dynamic range in AGC(Automatic Gain Control) locking. At the transmitter, the -49.46 dBc of spurious emission suppression is attained when the output power of the transmitter is 34.3 dBm. These results are good enough to meet to standard performance specifications.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.6
• /
• pp.1259-1265
• /
• 2013

In wireless environment such as wireless LAN, proper location of wireless LAN AP allows us to take an effective coverage to provide good wireless communication service. To simulate wireless environment, FDTD formulation is introduced and Gaussian pulse injection in grid space is considered to be replaced wireless LAN AP. So structural effect corresponding to location of arbitrary obstacle must be considered, and its received gain is estimated. An obstacle in scattering field should be modeled to be conductor and concrete wall and its diffraction effect for some cross wall is evaluated between transmitter and receiver point.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2018.10a
• /
• pp.251-254
• /
• 2018

Research about IoT system that utilizes variation of wireless received signal according to the changing of the surrounding environment are actively being studied. In this paper, firstly we proved that the received signal strength changes according to the ambient temperature variation. Then, we proposed the fire detection scheme by using received signal strength variation when the signal exchange between fixed transmitter and receiver periodically. The proposed scheme consists of the received signal strength change detection unit and the internal receiver temperature detection unit which prevents misunderstanding the received signal strength variation by the changing of wireless channel environment as outbreak of fire. The proposed scheme has the advantage of being able to support the existing receiver through software upgrade without additional device.