• Proceedings of the IEEK Conference
• /
• 2002.06e
• /
• pp.55-58
• /
• 2002

This paper describes an RF module for 2.4GHz wireless audio/video transmission. The pre-processed baseband input signals are FM-modulated using a VCO and then transmitted through an antenna after RF filtering. The designed circuits are implemented using a Teflon board of which the size is 52mm${\times}$62mm. The measured maximum output signal levels are around -3dBm and the harmonics are less than -450dBc. The manufactured module consumes 130mA from a 8V supply.

• Journal of Korea Multimedia Society
• /
• v.23 no.9
• /
• pp.1164-1170
• /
• 2020

In this paper, we consider the wireless-powered backscatter communication which consists of a power beacon, a source, a relay, and a destination. For the proposed wireless-powered backscatter communication, the source transmits its signals to both the relay and the destination via a backscattering channel and the relay which has a rechargeable battery performs an energy harvesting as well as an information forwarding based on the time switching relay (TSR) protocol. Based on the decode-and-forward (DF) relay transmission, we investigate performances of the proposed system in terms of outage probability and transmission rate in which the exact performance analysis of outage probability is given. Finally, some numerical examples are given to verify our provided analytical results for different system conditions.

• Journal of Broadcast Engineering
• /
• v.18 no.3
• /
• pp.491-494
• /
• 2013

This paper proposes a stochastic/dynamic routing protocol which aims the minimization of the summation of time average expected power expenditure with buffer stability in mobile ad-hoc 60 GHz wireless networks. By using 60 GHz RF, the wireless devices can transmit/receive 1080p HD video signals without compression. In addition, our algorithm works without centralized controller, so that the distributed operation is available. The novelty of the proposed algorithm was also verified by simulations.

• Journal of Digital Contents Society
• /
• v.11 no.2
• /
• pp.277-282
• /
• 2010

In this paper, the wireless transmission module is developed to transmit oxygen saturation(SpO2) signal, acquired from bio-signal measuring module, to PC. This wireless transmission module is designed with closed type protocol instead of open type protocol such as a zigbee or a bluetooth, considering of the security of personal medical informations. The display software is also developed to display transmitted SpO2 signals by various type data and graph without information loss for a emergency transfer.

• Journal of information and communication convergence engineering
• /
• v.9 no.5
• /
• pp.562-566
• /
• 2011

As telecommunication technologies in telemedicine services are developed, the expeditious development of wireless and mobile networks has stimulated wide applications of mobile electronic healthcare systems. However, security is an essential system requirement since many patients have privacy concerns when it comes to releasing their personal information over the open wireless channels. Due to the invisible feature of mobile signals, hackers have easier access to hospital networks than wired network systems. This may result in several security incidents unless security protocols are well prepared. In this paper, we analyzed authentication and authorization procedures for healthcare system architecture to apply secure M-health systems in the hospital environment. From the analyses, we estimate optimal requirements as a countermeasure to its vulnerabilities.

• Journal of Korean Association for Spatial Structures
• /
• v.18 no.2
• /
• pp.51-58
• /
• 2018

Recently, measuring instruments for SHM of structures had being developed. In general, the wireless transmission of sensor signals, compared to its wired counterpart, is preferable due to its absence of triboelectric noise and elimination of the requirement for cumbersome cable. However, the research on the tall buildings with relatively small vibration levels is insufficient. Therefore, in this paper, we used the wireless MEMS sensor and iPad to compare and analyze the vibration measurements of three tall buildings and two towers.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.8
• /
• pp.1099-1105
• /
• 2018

Wireless sensor networks have been shown to be an effective method for health monitoring of civil structures. In this paper a wireless strain sensor system which will allow easier collection of accurate strain signals in small sized structures is described. The experiment result shows that the developed wireless sensor system and the proposed network system are fit for health & safety monitoring and control of structures.

• Proceedings of the IEEK Conference
• /
• 2002.07c
• /
• pp.2059-2062
• /
• 2002

For detection of digitally modulated signals, the receiver must be provide with accurate carrier phase and symbol timing estimates. So far, tots of algorithms have been suggested for those purposes. In general, a interpolation filter with TED(Timing Error Detection) like Gardner algorithm is popularly used for symbol timing estimate of digital communication receiver. Apart from the performance point of view, a multiplicative operation of any interpolation filter limits the symbol rate of the system. Hence, we suggest a new symbol timing estimate algorithm for high speed burst-mode fixed wireless communication system and analyze its performance in the AWGN channel.

• Journal of Korean Association for Spatial Structures
• /
• v.17 no.3
• /
• pp.57-64
• /
• 2017

Recently, measuring instruments for SHM of structures had being developed. In general, the wireless transmission of sensor signals, compared to its wired counterpart, is preferable due to its absence of triboelectric noise and elimination of the requirement for cumbersome cable. Preliminary studies on the continuous vibration measurement of high-rise buildings using MEMS sensors have been carried out. However, the research on the low-rise buildings with relatively small vibration levels is insufficient. Therefore, in this paper, we used the wireless MEMS sensor to compare and analyze the vibration measurements of three low-rise buildings.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.883-886
• /
• 2005

This paper proposed a wireless measurement system (WMS) for an effective condition monitoring using wireless communication. WMS consists of two parts: transmitter(TM) acquired a dynamic signal from physical system using ICP type accelerometer sensor. An acquired signal modulated through the low/high pass filter and amplifier in DAQ board, which converted to digital signal. Embedded board(E-board) transferred digital signals to base station(BS) through the socket IEEE.802.11.b. BS is adopted IOCP server structure. Because it can acquired signal well during transferred digital signal. Signal processing used LabVIEW Library, BS(server) designed to realize multi-thread using visual C++.NET for 1 many meaning data processing